Alliance Laundry Systems CI 1650/325 User manual

Cylinder ironer
Cl 1650/325
Cl 2050/325
Technical specifications
Installation instructions
Operating instructions
Maintenance
Part No. D1273
Code: B12340801
September 2010
Instruction
manual

Contents
Explanation of Safety Messages
Important Safety Instructions .
Description of structural components .
Workplaces and noise level .
Technical data CI1650/325, CI2050/325 ..
Warranty and service instructions ..
Initial setup of the machine .
Transport and machine fastening .
Operating devices and their position ...
Functions .
Failure and information signals .
Machine function, adjustment and troul
Description of machine functions .
"Manu" adjusting menu
"Coin"adjusting menu ...
Display menu .
Central panel .
Sigma explorer .
Maintenance .

Safety Information
1
Explanation of Safety Messages
Throughout this manual and on machine decals, you will find precautionary statements (“DANGER", "WARNING” and
“CAUTION”) followed by specific instructions. These precautions are intended for the personal safety of the operator,
/L |
DANGER
avoided, will cause Mver^^rsonaMnJuiyor'deaths
A |
WARNING
S" n ot avoided ' c ould
a i
CAUTION
damage.
Additional precautionary statements (“IMPORTANT” and “NOTE") are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used to inform the reader of specific procedures where minor

1
Safety signs and labels are also placed on the unit Those signs and labels are limited messages.
Where needed, further explanations are provided below. These signs are to be inspected for readability and

Safety notice
CAUTION: Note for installation
The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of
codes, with the NATIONAL ELECTRICAL CODE, ANSI/NFPA 70, or Canadian Electrical Code, CSA C22.1.

1
Important Safety Instructions
Save These Instructions

1
To reduce the risk of fire, DO NOT put articles which have traces of any flammable substances such
as machine oil, flammable chemicals, thinner, etc., or anything containing wax or chemicals such as
in mops and cleaning cloths, or anything dry-cleaned at home with dry-cleaning solvent in the ironer.
ALWAYS disconnect the electrical power to the ironer before servicing. Disconnect power by shutting
off appropriate breaker of use.
Install this ironer according to the Installation Instructions in this manual.
All connections for electrical power, grounding, and gas supply must comply with local codes and be
made by licensed personnel when required.
/t\ I WARNING
To prevent serious injury or death, read ironer
manuals before installing, operating, maintaining,
or cleaning the ironer.

Product description
2
Intended use
The machine, described in this manual is solely intended to use it for ironing of
It is not suitable for garments or other thick linen.
/h
WARNING
Any other use of the machine may involve risks to persons
and must therefore only take place after previously
obtained written approval from the manufacturer.
Equipment and components on the machine, which are important to safety and
health, have been constructed in preparation for an expected life of 15,000 operating
hours - however max. 10 years from the time of manufacture.
within this period implies that the prescribed maintenance
Normally the ironed pieces are coming into the outlet tray after ironing, where the
operator can take them without any danger.
WARNING
It may involve risk of burning to the operator when taking
the sheets directly from the roll, deeper into the machine
at the outlet tray. Jams should always be taken away by
authorized personnel. _
The normal, permanent working places of the operating personnel (operator) have
been marked on the layout.
It may involve risk to the operator to work on or under
the machine. Work Stay in these areas is only allowed for
stopped, cooled down and the main switch has been locked
in position "0".
— Important -
This manual is a part of the delivered machine volume, and is to be handed
If any doubt should occur about the contents in the manuals in your local
installed, it will always be the English text, which is valid.

Description of structural components
This machine is delivered in various types adjusted to the needs of the individual
laundry. The principal components of the machine are the following:
1. Operation panel
2. Emergency stop
3. Input conveyor
5. Tray for wet linen
6. Foot stop (option)
7. Exhaust pipe (top or back / option)
Further information about the construction of this machine will appear from the
"Techical data" paragraph in the manual.

2

2
Technical data CI1650/325, CI2050/325
I
I

2
Sound level measurement
Conversion table
= 0.556. (”F-32)
°C = 32.0 °F)

2
Warranty and service instructions

3
Transport and machine
fastening

3
Setting up the machine
Preparation of the machine
- Inspect the machine by delivery on any damage.
- The machine can be moved by a manual pallet lifter.
- Remove the packing carefully and remove the parts on top of the machine.
- Place the machine on its final position. Keep in mind that the sides of the
machine have to be free of any surroundings of at least 1 meter.
- The back must be at least 30 cm from the wall because of the turning cover.
//////////////////////////
^ 30 cm
©
D D
»
u 1 1 11111 1 11111 1 1 1111 y
16 -

3
Exhaust system
Whenever possible, install the ironer along an outside wall where duct length can be kept to a minimum, and
make-up air can be easily accessed. The construction must not block the airflow at the rear of the ironer.
Doing so would prevent adequate air supply to the ironer combustion.
- Note -
Never connect an ironer duct at a 90° angle to the collector dust (see picture below).
Doing so will cause excessive back pressure, resulting in poor performance.
Never connect two ironer exhaust ducts directly across from each other at the point of
entry to the collector dust.
Number of ironers
Diameter of the exhaust pipe (in mm)
Ventilation aperture required section (in dm 2 )
D1
100
0,8
D2
150
D3
225

3

3
Right-angled corner: 13.4
90 degrees smooth bend R/D = 2 :2.1
90 degrees angular bend R/D = 2 (three sections): 2.6

3
20 -