Alliance Laundry Systems BWNBC2PP113TW01 Installation manual

Programming
Topload Washer
Refer to Page 7 for Model Identification
WASH RINSE SPIN
NORMAL
HOT
NORMAL
WARM
NORMAL
COLD
START
DELICATES
COLD
PERM
PRESS
WARM
TLW49R_SVG
TLW50R_SVG
Original Instructions
Keep These Instructions for Future Reference.
CAUTION: Read the instructions before using the machine.
(If this machine changes ownership, this manual must accompany machine.)
Part No. 203677ENR3
January 2019

WARNING
Failure to install, maintain, and/or operate this ma-
chine according to the manufacturer's instructions
may result in conditions which can produce bodily
injury and/or property damage.
W030
WARNING
For your safety and to reduce the risk of fire or an
explosion, do not store or use gasoline or other
flammable vapors and liquids in the vicinity of this or
any other appliance.
W022
NOTE: The WARNING and IMPORTANT instructions ap-
pearing in this manual are not meant to cover all possi-
ble conditions and situations that may occur. It must
be understood that common sense, caution, and care-
fulness are factors which cannot be built into these
washers. These factors MUST BE supplied by the per-
son(s) installing, maintaining, or operating the unit.
Always contact the distributor, service agent, or the manufacturer
about any problems or conditions you do not understand.
Read all instructions before using unit.
Hazardous voltage inside. Disconnect power before serv-
icing.
This product uses FreeRTOS V7.2.0 (www.freertos.org).
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
3 Part No. 203677ENR3

Table of Contents
Model Identification............................................................................... 7
Preliminary Information.........................................................................8
About the Control........................................................................................... 8
Glossary of Terms...........................................................................................8
Power Failure Recovery.................................................................................. 8
Serial Card Reader Communications (Card Models Only).................................. 8
Control Identification............................................................................. 9
Select Cycle Pads........................................................................................... 9
Display Identification............................................................................10
Light Emitting Diodes (LEDs)....................................................................... 10
CYCLE LED............................................................................................ 10
WASH LED..............................................................................................10
RINSE LED..............................................................................................10
SPIN LED................................................................................................ 10
7-Segment Digits.......................................................................................... 10
Washer Operation.................................................................................11
Power Up .................................................................................................... 11
Ready Mode................................................................................................. 11
Partial Vend Mode.........................................................................................11
Additional Vend Mode...................................................................................11
Start Mode....................................................................................................11
End of Cycle Mode....................................................................................... 11
Cycle Sequence.............................................................................................11
Opening the Washer Lid................................................................................ 11
Changing Cycles...........................................................................................11
Special Features ...................................................................................12
Programming Control....................................................................................12
Collecting Audit Information......................................................................... 12
Testing Machine and Control Functions.......................................................... 12
Rapid Advance Feature................................................................................. 12
Clearing the Vend Feature .............................................................................12
Communications Mode..................................................................................12
Coin Drop.................................................................................................... 12
Start Pulse Operation.....................................................................................12
© Copyright 2019, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed
written consent of the publisher.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
4 Part No. 203677ENR3

Service Door and Coin Vault Openings........................................................... 12
OPL Mode................................................................................................... 12
Opening the Service Door..................................................................... 13
Coin Models.................................................................................................13
Card Reader Models......................................................................................13
Entering the Manual Mode................................................................... 14
How to Enter the Manual Mode......................................................................14
Manual Mode Navigation.............................................................................. 14
Programming Control...........................................................................16
What Can Be Programmed.............................................................................16
Programmable Options Available................................................................... 16
Vend Price AtS............................................................................................. 16
Coin 1 Value dEn1........................................................................................ 16
Coin 2 Value dEn2........................................................................................ 17
Start Pulse Value PLSE..................................................................................17
Default Cycle dCyC...................................................................................... 18
Cycle Programming CyCP.............................................................................18
Card Reader Display Control CArd................................................................ 18
Audio Signal AUd........................................................................................ 19
How to Program the Audio Signal...............................................................19
Error Code Programming Err......................................................................... 19
OPL Parameters oPL.....................................................................................19
Collecting Audit Information................................................................ 21
How to Enter Audit Feature........................................................................... 21
Entering the Audit Feature by Manual Mode................................................... 21
Entering the Audit Feature with the Coin Vault Open....................................... 21
How to Read Audit Data................................................................................21
How to Exit Audit Feature............................................................................. 21
Manual Reset........................................................................................22
How to Enter Manual Reset........................................................................... 22
Testing Machine and Electronic Control Functions............................... 23
How to Enter Testing Feature.........................................................................23
How to Start Tests.........................................................................................23
How to Exit Testing Feature ..........................................................................23
Diagnostic (Testing) Mode – Quick Reference Chart........................................ 23
Diagnostic Test Descriptions..........................................................................26
Control Software Version Number Test d 1.................................................. 26
Input/Output Software Version # Test d 2.....................................................26
Service Door Opening Test d 8................................................................... 26
Coin Vault Opening Test d 9.......................................................................26
Coin Drop 1 Input Test d 10....................................................................... 26
Coin Drop 2 Input Test d 11........................................................................26
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
5 Part No. 203677ENR3

Vend Connection Header Present Test d 12.................................................. 26
Start Pulse Test d 13.................................................................................. 26
Lid Switch Input Test d 15......................................................................... 27
Show Fill Time Test d 17........................................................................... 27
Show Drain Time Test d 18........................................................................ 27
External Outputs Test d 23......................................................................... 27
Water Purge Test d 24................................................................................ 27
Water Leak Detection Test d 25.................................................................. 27
Water Level Test d 26................................................................................ 28
Configuration 1 Display Test d 29...............................................................28
Configuration 2 Display Test d 30...............................................................31
Configuration 3 Display Test d 31...............................................................31
Configuration 4 Display Test d 32...............................................................31
Configuration 5 Display Test d 33...............................................................31
Factory Test..................................................................................................31
To Enter Factory Test.................................................................................32
To Exit Factory Test...................................................................................32
Error Codes .........................................................................................35
Rapid Advance Feature.........................................................................38
How to Enter Rapid Advance.........................................................................38
How to Exit Rapid Advance Feature............................................................... 38
Power Fail Recovery............................................................................. 39
Communications Mode......................................................................... 40
Card Reader Communications - Card Models Only.......................................... 40
Default Cycle Time .............................................................................. 41
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
6 Part No. 203677ENR3

Model Identification
Information in this manual is applicable to these washer models:
BWNBC2PP113TW01 HWNBX2SP115CW01 SWNBX2SP113FW01
BWNBX2PP303AW01 HWNBX2SP123DW01 SWNBX2SP113JW01
BWNBX2SP303AW01 HWNBX2SP303NW22 SWNBX2SP115TQ02
HWNBC2PP113TW01 HWNBX2SP543DW01 SWNBX2SP115TW02
HWNBC2PP115TQ01 HWNBY2PP115TW01 SWNBX2SP123DW01
HWNBC2PP115TW01 HWNBY2SP115CW01 SWNBX2SP303AW01
HWNBC2SP115TW01 HWNBY2SP115TW01 SWNBX2SP303NQ22
HWNBD2SP115CW01 NWNBX2SP303NW22 SWNBX2SP303NW22
HWNBE2SP115CW01 NWNBX2SP543NW23 SWNBX2SP543DW01
HWNBX2SP113FW01 SWNBC2SP115TW02 SWNBY2SP115TW01
TWNBX2SP303NW22
Model Identification
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
7 Part No. 203677ENR3

Preliminary Information
About the Control
This control is an advanced, programmable computer that lets the
owner control most machine features by pressing a sequence of
keypads.
The control allows the owner to set vend prices, retrieve audit in-
formation, run diagnostic tests and set other programmable fea-
tures. Washers shipped from the factory have a default cycle set-
ting of NORMAL COLD built in. However, the owner can
change the default cycle, or any cycle, as needs permit.
IMPORTANT: In the event of a power failure, the control
will not have to be reprogrammed. It is designed with a
memory system that will remember how it was pro-
grammed until the electrical power is restored.
IMPORTANT: It is extremely important that the washer
has a good ground connection and that all mechanical
and electrical connections to the control are made be-
fore applying power to or operating the washer.
Glossary of Terms
The following are a few terms and abbreviations to learn. These
are referred to throughout the instructions.
Display – This term refers to the window area of the control that
displays words and values.
LED (Light Emitting Diode) – This term refers to the lights next
to the keypads and status words of the control.
FEC – Front End Control
I/O Board – Input/Output Board
OPL – On Premises Laundry
Power Failure Recovery
If a cycle is in progress and the power fails, the cycle status is
saved in memory. When the power recovers, the washer will re-
sume into the previously active cycle.
Serial Card Reader Communications
(Card Models Only)
The control will accept communication with a serial card reader
in order to perform vending transactions when a card is inserted
to pay for cycles. The card reader can also allow the owner to
program a limited number of features and collect audit informa-
tion.
For detailed information on serial card reader communications,
refer to instructions included with card reader.
Preliminary Information
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
8 Part No. 203677ENR3

Control Identification
Select Cycle Pads
SELECT CYCLE pads are used to select the specific washer cy-
cle. These pads include NORMAL HOT, NORMAL WARM,
NORMAL COLD, PERM PRESS WARM and DELICATES
COLD. These pads allow the user to select a cycle other than the
default cycle (NORMAL COLD).
The SELECT CYCLE keypads are not active after the first fill
step of the cycle. The selected cycle is indicated by the light
(LED) on the pad. Pressing the flashing START pad will confirm
the selection and the cycle will begin.
When a card reader is used, pressing the START pad will start the
cycle and deduct the vend price from the card.
WASH RINSE SPIN
NORMAL
HOT
NORMAL
WARM
NORMAL
COLD
START
DELICATES
COLD
PERM
PRESS
WARM
TLW49R_SVG1
1
3
2
4
5
6
TLW50R_SVG1
1
3
2
4
5
6
1. LED Light
2. SELECT CYCLE pads
3. Four 7-Segment Digits
4. Display
5. LED Status Lights
6. START pad
Figure 1
Control Identification
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
9 Part No. 203677ENR3

Display Identification
Light Emitting Diodes (LEDs)
LIGHT EMITTING DIODES (LEDs) are used to indicate the
chosen cycle and cycle status. See below for information on each
LED.
CYCLE LED
CYCLE LED will remain lit the entire cycle.
WASH LED
WASH LED is lit at the beginning of a wash portion of the cycle
and will remain lit until the wash is complete.
RINSE LED
RINSE LED is lit at the beginning of a rinse portion of the cycle
and will remain lit until the rinse is complete.
SPIN LED
SPIN LED is lit during the Final Spin portion of the cycle.
7-Segment Digits
The 7-SEGMENT DIGITS are used to display the time remain-
ing in a cycle, vend price, error messages and descriptive codes.
During diagnostic testing or manual programming of the control,
these digits will display descriptive codes and values.
Display Identification
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
10 Part No. 203677ENR3