Allmatic BIOS1 BRT Safety guide

CONTROL UNIT BIOS1 BRT
Programmable Control board for barriers BRT
Manual for installation
Compatible from firmware version BIOS1BRT01

ITA ENG FRA ESP DEU POR 2 / 12
6-1622245 rev.3 23/12/2016
Compatible from firmware version BIOS1BRT01
The control unit BIOS1 BRT is particularly indicated for barriers 230 Vac motor with maximum power absorbed of 700W. The control unit is equipped
with a display that allows a precise regulation of the thrust. The control unit can memorize up to 1000 transmitters (8000 as optional), with the step by
step, partial opening, open and close functions.
It is supplied with inputs for photocells, safety edge (mechanical or 8k2), magnetic loop, the buttons for step by step, partial opening, open, close and
stop. The outputs include a 230 Vac flashing light, courtesy light/zone light/open gate light, 24 Vdc accessories power supply.
1. Introduction
2. Configuration
3. Connections
ATTENTION: DO NOT INSTALL THE CONTROL UNIT WITHOUT READING THE INSTRUCTIONS FIRST !!!
THE INSTALLATION SHOULD BE PERFORMED ONLY BY QUALIFIED PERSONNEL.
Be sure that the limit switches are connected and correctly adjusted (see mechanical instruction)
Line
FUSE
F 6.3 A
Accessories
FUSE
F 0.5 A
SAFETY
DEVICES
DIP SWITCH
MEMORY
MOTOR OUTPUT
Connect the common of the motor to the clamp
motor COM of the control unit.
Connect the phase 1 of the motor to the clamp
motor L1 of the control unit.
Connect the phase 2 of the motor to the clamp
L2 of the control unit.
Motor condensers 230 Vac
!Risk of electric shock!
CAPACITOR
Connect the capacitor to the clamps COND of
the control unit.
LIMIT SWITCHES
Connect the NORMALLY CLOSED contact of
the limit switches to the control unit
During the learning of the stroke phase the control
unit recognize itself the opening and closing limit
switch.
ANT.
C.A.

ITA ENG FRA ESP DEU POR 3 / 12
6-1622245 rev.3 23/12/2016
Compatible from firmware version BIOS1BRT01
SAFETY EDGE INPUT
Connect the safety edge contacts to the clamps
9 and 10 of the control unit.
Select the type of security edge used
PH2 MULTIFUNCTION INPUT
Connect the NORMALLY CLOSED contact of
the photocell (PHOTO 2) between the clamps 11
and 18 of the control unit. Otherwise use
another function NO or NC.
This input can be set on the menu  as closing
photocell, magnetic loop or clock.
If not used set the DIP switch PH2 ON and select
on the advanced menu =0.
PH1 PHOTOCELL INPUT
Connect the NORMALLY CLOSED contact of
the photocell (PHOTO 1) between the clamps 12
and 18 of the control unit.
Functioning:
- Closing: immediate inversion of movement.
- Opening: no intervention during the movement.
- With barrier stopped, not allow the closing.
If not used set the DIP switch PH1 ON.
STOP INPUT
Connect the NORMALLY CLOSED contact of
the STOP between the clamps 13 and 18 of the
control unit.
If not used set the DIP switch STOP ON.
OPEN INPUT
Connect the button OPEN or the opening loop
(NORMALLY OPEN contact) between the
clamps 14 and 18 of the control unit.

CLOSE INPUT
Connect the button CLOSE between the clamps
15 and 18 of the control unit.
PED MULTIFUNCTION INPUT
Connect the button PED between the clamps 16
and 18 of the control unit. Otherwise use
another function NO or NC.
This input can be set on the menu  as closing
photocell, magnetic loop or clock.
STEP BY STEP INPUT
Connect the button SS between the clamps 17
and 18 of the control unit.
ANTENNA
Connect the signal cable of the antenna to the
clamp 19 and the ground of the antenna to the
clamp 20 of the control unit.
The presence of the metallic parts or humidity in the
walls could have negative influences on the range of
the system. We suggest therefore to not place the
receiving antenna and/or transmitters near big
metallic objects, near the floor or on the ground.
(mechanical or 8K2) through the menu .
In case of intervention, moves in opening
immediately.
If not used set the DIP switch EDGE ON.
COURTESY LIGHT OUTPUT
Connect the courtesy light to the clamps 3 and
4, 230Vac 100W MAX.
FLASHING LIGHT OUTPUT
Connect the flashing light to the clamps 3 and
5.
It is possible to light up the action area of the
automatism during each motion.
The functioning of the auxiliary light is controlled in
the advanced menu .
Use a flashing light without self flashing card
230Vac 60W MAX
PHOTOCELLS POWER SUPPLY
Connect the clamp 6 of the control unit to the
clamp + of the power supply of the photocells
receiver.
Connect the clamp 7 of the control unit to the
power supply clamp - of the photocells receiver
and of the transmitter.
Connect the clamp 8 of the control unit to the
power supply clamp of the trasnmitter of the
photocells.
The photocells test is activated in the advanced
menu .
ATTENTION: the control unit gives a voltage of 24
Vdc and can supply a maximum power of 4W.
For the safety edge test connect the test device of
the safety edge on the power supply pins of the TX
(test activated wiht low logic signal 0Vdc).
Please refer to the manual of the safety edge.
POWER SUPPLY
Connect the power supply cable between clamp
1 and 2 of the control unit
Power supply 230 Vac 50 Hz
Do not connect the card directly to the electric
network. Put a device which can ensure the
disconnection of each pole from the power supply of
the control unit.

ITA ENG FRA ESP DEU POR 4 / 12
6-1622245 rev.3 23/12/2016
Compatible from firmware version BIOS1BRT01
5. Remote control learning
5.1 Learning of one transmitter
A transmitter is memorized a key at a time: The 1st memorized key performs the OPEN function, the 2nd key performs CLOSE function, the 3rd key
performs the STEP by STEP function (opening and closing of the gate) and the 4th key performs the partial opening.
The control unit exits from the learning phase if no new key or transmitter command is given in 10 seconds.
The learning procedure is the following:
4. Installation sample
Photocell
Photocell
Barrier BRT
Command
device
Photocell
Photocell
Opening
loop
Zone loop
Closing
loop
Safety edge
Press one key of the transmitter
On the display will appear
and the flashing light lights on
Make sure that the board is out of any
menus, press the button UP[+]
On the display will appear .
If the transmitter was already
memorized will appear .
After 2 seconds the display will show the
memory location of the memorized transmitter,
for example
If you want to memorize another key or a new
transmitter repeat the procedure
4.2 Learning with the hidden key of an already memorized transmitter
With the hidden key of a transmitter it is possible to enter the learning phase in order to memorize new keys or new transmitters.
With the automation still, with the aid of a clip press the hidden button of an already memorized transmitter, the flashing light lights on, now it is
possible to memorize new keys or transmitters.
4.3 Cancellation of one transmitter
1
2
Enter the learning phase with the UP[+] button or with the hidden key of a memorized transmitter (see 5.1 or 5.2).
Press in the same time the hidden key and 1st key of the transmitter that you want to cancel.
The flashing light bilnks 4 times and on the display will appear

ITA ENG FRA ESP DEU POR 5 / 12
6-1622245 rev.3 23/12/2016
Compatible from firmware version BIOS1BRT01
6
6.1 Easy settings of the stroke (parameter ≠ )
Press and keep pressed the buttons UP[+] e MENU
for at least 5 seconds.
The barrier moves in opening.
If the barrier moves in closing press the button
DOWN to stop and reverse the direction of
movement and give a step by step command
(SS) to resume the procedure
Unlock the barrier and move it to the middle of the
stroke
Be sure that the limit switches are connected and correctly adjusted (see mechanical instruction)
Be sure that the barrier is positioned in the middle of the stroke. Limit switches must not be activated.
When the barrier reaches the opening limit switch it
stops by itself
The barrier moves in closing
When the barrier reaches the closing limit switch it
stops by itself
The barrier moves in opening
6.2 Advanced settings of the stroke (parameter = )
Be sure that the limit switches are connected and correctly adjusted (see mechanical instruction)
Be sure that the barrier is positioned in the middle of the stroke. Limit switches must not be activated.
In this procedure is necessary to provide the positions of beginning of slowing down with a step by step command (SS).
1
2
3
4
5
6 Setting stroke
7
When the barrier reaches the opening limit switch it
stops by itself
The barrier closes with the settings of slowing
down set in the menu. When the barrier is closed
the learning phase is ended.
Press and keep pressed the buttons UP[+] e MENU
for at least 5 seconds.
The barrier moves in opening.
If the barrier moves in closing press the button
DOWN to stop and reverse the direction of
movement and give a step by step command
(SS) to resume the procedure
Unlock the barrier and move it to the middle of the
stroke
When the barrier reaches the opening limit switch it
stops by itself
The barrier moves in closing
When the barrier reaches the closing limit switch it
stops by itself
The barrier moves in opening
1
2
3
4
5
When the barrier reaches the opening limit switch it
stops by itself
The barrier closes with the settings of slowing
down set in the menu. When the barrier is closed
the learning phase is ended.
When the gate reaches the position of beginning of
slowing down give a step by step command (SS)
The barrier begins the slowing down
When the gate reaches the position of beginning of
slowing down give a step by step command (SS)
The barrier begins the slowing down
Warning: in case of intervention of a safety device, the learning is stopped and will appear on the display the written
Press Step by Step key to start again the learning from the 2nd point.
Warning: in case of intervention of a safety device, the learning is stopped and will appear on the display the written
Press Step by Step key to start again the learning from the 2nd point.

ITA ENG FRA ESP DEU POR 6 / 12
6-1622245 rev.3 23/12/2016
Compatible from firmware version BIOS1BRT01
7.1 Base settings menu:
MENU DESCRIZIONE VALORI IMPOSTABILI
min-max DEFAULT UNITÀ
 Auto reclosing time (0 = disabled) 0-900 0 s
 Auto reclosing time after transit(0 = disabled) 0-30 0 s
 Motor torque (running torque) 10-100 100 %

Slowing down mode
0 = normal
1 = fast with more torque
0-1 1

Step by step configuration
0 = normal (OP-ST-CL-ST-OP-ST…)
1 = alternated STOP (OP-ST-CL-OP-ST-CL…)
2 = alternated (OP-CL-OP-CL…)
3 = condominium – timer
4 = condominium with immediate auto reclosing
0-4 1

After black-out
0 = no action
1 = closing
0-1 0

Soft start
0 = disabled
1 = enabled
0-1 0

Amplitude of slowing down
P = personalized during learning
0…100% = percentage of stroke
0-100 15 %
7. Menu
Entering the menu:
To enter the base menu settings keep pressed the MENU button for at least one second
To enter the advanced menu settings keep pressed the MENU button for at least five seconds
Navigation into the menu:
It is possible to move from an entry to another one using UP[+] e DOWN[-] buttons.
To change a parameter keep pressed the MENU button for at least 1 second until the parameter begins blinking,
so release the key.
Use UP[+] and DOWN[-] buttons to change the parameter.
At the end keep pressed MENU for al least 1 second until the parameter stops blinking to save the change.
A quick pressure of the menu key is enough to leave a menu
Ex. Base menu
Ex. Advanced menu
*ATTENTION!
It is not advisable the disabling of the slowing downs and, if possible, use the "soft start" function.
*
*

ITA ENG FRA ESP DEU POR 7 / 12
6-1622245 rev.3 23/12/2016
Compatible from firmware version BIOS1BRT01
7.2 Advanced menu:
MENU DESCRIZIONE VALORI IMPOSTABILI
min-max DEFAULT UNITÀ
..
PH2 multifunction input setting:
0 = Closing photocell
1 = Closing loop NO
2 = Closing loop NC
3 = Zone loop NO
4 = Zone and closing loop NO
5 = Loop for enable command OPEN
6 = Clock
0-6 0
..
Photocells test
0 = disabled
1 = enabled PHOTO1
2 = enabled PHOTO2
3 = enabled PHOTO1 and PHOTO2
0-3 0
..
Safety edge type
0 = contact (NC)
1 = resistive (8k2)
0-1 0
..
Safety edge test
0 = disabled
1 = enabled
0-1 0
.. Partial opening 0-100 30 %

PED multifunction input setting:
0 = Partial opening
1 = Closing loop NO
2 = Closing loop NC
3 = Zone loop NO
4 = Zone and closing loop NO
5 = Loop for enable command OPEN
6 = Clock
0-6 0
..
Blinker output mode
0 = Fix
1 = Blinking
0-1 1
.. Pre-flashing time (0 = disabled) 0-10 0 s
..
Courtesy ligth settings
0 = At the end of movement for a TCY time
1 = On if the barrier is not closed + TCY time
2 = On if courtesy light timer (TCY) not expired
3 = Open barrier light on/off
4 = Open barrier light with proportional flashing
0-4 3
.. Courtesy light time 0-900 0 s
..
Dead-man
0 = disabled
1 = enabled
0-1 0
.. Setting threshold of cycles for assistance request. Once limit is reached the next
cycles will be done with fast blinking (only if  enabled) (0 = disabled) 0-100 0 x1000
cicli
..
Continuous blinking for assistance request (done only with closed gate).
0 = disabled
1 = enabled
0-1 0
.. Restore defaul settings, enter to modify the parameter and then keep pressed the
MENU button, a count down appears that ends with  on the display
.. Cancelling all transmitters, enter to modify the parameter and then keep pressed
the MENU button, a count down appears that ends with  on the display
Cancellation of a single transmitter 0-999
Viewing of the memory location for a single transmitter 0-999

ITA ENG FRA ESP DEU POR 8 / 12
6-1622245 rev.3 23/12/2016
Compatible from firmware version BIOS1BRT01
7.3 Menu description:
7.3.1 Base settings menu
Auto reclosing time
Active when the barrier is in the completely open position or in partial opening, the barrier automatically closes after  seconds. In this phase the
display shows with the blinking dash, that during the last 10 seconds will be replaced by the count down.
Auto reclosing time after transit
If in the opening phase or in the completely open position the beam of the PH1 photocells is obscured and freed, the barrier automatically closes after
 seconds when the completely open position is reached, In this phase the display shows with the blinking dash, that during the last
10 seconds will be replaced by the count down.
Motor torque
Adjust the motor torque to ensure a correct functioning of the barrier. It is possible to adjust the percentage of torque between 10% to 100%. After the
adjustement of this parameter it is recommended to perform a complete movimentation (opening and closing) to ensure a correct functioning of the
barrier.
Slowing down mode
The control unit has 2 different type of slowing downs : standard or with higher torque and speed.
Step by step configuration (SS)
 = 0 Normal (OP-ST-CL-ST-OP-ST…)
Typical functioning of Step by Step. During the movement a SS command stops the barrier.
 = 1 Alternated STOP (OP-ST-CL-OP-ST-CL…)
Alternated functioning with STOP during the opening. During the opening phase a SS command stops the barrier.
 = 2 Alternated (OP-CL-OP-CL…)
The user cannot stop the barrier during the movement with a SS command.
A SS command during the movement inverts the movement.
 = 3 Condominium – timer
A SS command only opens the barrier. When the barrier is completely open, if the command persist the control unit will wait until the opening
of the contact before beginning the contdown of the automatic reclosing (if enabled). Another SS command in this phase will restart the
contdown of the automatic reclosing.
 = 4 Condominium with immediate auto reclosing
Like condominium – timer (previous point) but during the countdown a SS command will close the barrier, when it is in the completely open
position .
After black-out
When the control unit turns on after a black-out,
 = 0 No action – when the control unit turns on the barrier does not move until the first command, the first movement is a slow opening.
 = 1 Closing– turning on the control unit it will perform a slow closing.
Soft start
The movement begins with reduced torque, used in light gates.
Amplitude of slowing down
With this parameter it is possible to adjust the amplitude of the slowing down and eventually disable it (=0). If you need more precise or different
slowing down between opening and closing it is possible to set the parameter on  (personalized) and perform an advanced learning of strokes
(6.2) providing also the beginning of slowing downs during the learning.
*ATTENTION!
It is not advisable the disabling of the slowing downs and, if possible, use the "soft start" function.
*
*

ITA ENG FRA ESP DEU POR 9 / 12
6-1622245 rev.3 23/12/2016
Compatible from firmware version BIOS1BRT01
7.3.2 Advanced menu
.. PH2 multifunction input setting
The control unit has six different functionings for PH2:
 .. = 0 Closing photocell:
- Closing: immediate inversion of movement.
- Opening: no intervention during the movement.
- With barrier stopped, not allow the closing.
 .. = 1 Closing loop NO: the control unit close the barrier when the
normally open contact opens, in this way when a vehicle exits and free
the loop, the control unit will command the closing.
 .. = 2 Closing loop NO: the control unit close the barrier when the
normally closed contact closes, in this way when a vehicle exits and
free the loop the control unit will command the closing.
 .. = 3 Zone loop NO: the control unit does not allow to close the
barrier until the normally open contact is closed.
 .. = 4 Zone and closing loop NO: the control unit does not allow to
close the barrier until the normally open contact is closed; when a
vehicle exits and free the loop, the contact opens and the control unit will
command the closing.
 .. = 5 Loop for enable the command OPEN: the control unit enables
the OPEN key (radio or wired) when the normally open contact is
closed.
 .. = 6 Clock: it is possible to connect a timer, with a normally open
contact, for the programming opening of the barrier. The contact is
interpreted as request of opening and of permanence on the opening
state until the contact remains closed. When the contact opens, the gate
automatically closes.
Warning: with function Clock activated user commands are inhibited.
.. Photocells test
Enabling this function, before each movement starting from still barrier, the control unit performs a functional check of the photocells. The check will
not be performed in case of fast movement after the intervention of a safety devices. Follow chapter 3 for the connections of the photocells.
.. Safety edge type
The control unit can work with two different type of safety edge:
 ..= 0 Mechanical with normally closed contact
 ..= 1 Resistive 8k2
.. Safety edge test
Enabling this function the control unit performs a functional check of the safety edge. This function is used if the edge connected to the control unit has
an electronic self test (exp. radio edge R.CO.O). Connect the test contact of the edge to the power supply of the trasmitter of the photocells (chapter 3)
and enable the self test with low voltage 0Vdc. For the compatibility follow the instruction of the manual of the safety edge.
.. Partial opening
Partial opening can be performed only starting from closed. The parameter sets the opening like a percentage of the total stroke of the barrier.
Closing loop
Zone loop
Loop for enable the opening
Closing
command
NO loop
NC loop
Not allowed the closing
Allowed the opening
.. PED multifunction input setting
The control unit has six different functionings for PED:
 .. = 0 Partial opening: it allows the partial opening of the barrier.
 .. = 1 Closing loop NO: the control unit close the barrier when the
normally open contact opens, in this way when a vehicle exits and free
the loop, the control unit will command the closing.
 .. = 2 Closing loop NO: the control unit close the barrier when the
normally closed contact closes, in this way when a vehicle exits and
free the loop the control unit will command the closing.
 .. = 3 Zone loop NO: the control unit does not allow to close the
barrier until the normally open contact is closed.
 .. = 4 Zone and closing loop NO: the control unit does not allow to
close the barrier until the normally open contact is closed; when a
vehicle exits and free the loop, the contact opens and the control unit will
command the closing.
 .. = 5 Loop for enable the command OPEN: the control unit enables
the OPEN key (radio or wired) when the normally open contact is
closed.
 .. = 6 Clock: it is possible to connect a timer, with a normally open
contact, for the programming opening of the barrier. The contact is
interpreted as request of opening and of permanence on the opening
state until the contact remains closed. When the contact opens, the gate
automatically closes.
Warning: with function Clock activated user commands are inhibited.
Closing loop
Zone loop
Loop for enable the opening
Closing
command
NO loop
NC loop
Not allowed the closing
Allowed the opening

ITA ENG FRA ESP DEU POR 10 / 12
6-1622245 rev.3 23/12/2016
Compatible from firmware version BIOS1BRT01
.. Flashing light output mode
It is possible to choose 2 different functioning for the blinker output:
 .. = 0 Fixed blinker output. It will be necessary to connect a self flashing blinker (B.RO LIGHT 230 Vac)
 .. = 1 Flashing light blinker output. It will be necessary to connect a fix light blinker (B.RO LIGHT FIX 230 Vac)
.. Pre-flashing time
Pre-flashing before each movement in both directions, .. seconds of pre-flashing
.. Courtesy light settings
The control unit has 4 different functionings for courtesy light:
 .. = 0 the light switches off at the end of a movement after .. seconds
 .. = 1 the light switches off only with closed barrier after .. seconds
 .. = 2 lighted on for .. seconds from the beginning of a movement, indipendently of the condition of the barrier (the light could switch off
before the end of movement)
 .. = 3 open barrier light - the light switches off immediately when the barrier reaches the closed position
 .. = 4 open barrier light with proportional blinking:
 opening – slow blinking
 closing – fast blinking
 opened – light on
 closed – light off
 stopped – 2flash + long wait + 2flash + long wait +…
.. Courtesy light timer
Courtesy light activation timer
.. Dead man
During dead man functioning mode the barrier moves only with a permanent command.
The enabled commands are OPEN and CLOSE. SS and PED are disabled. During dead man functioning all the automatic movements are disabled,
like short or total inversions. All safety devices are disabled except for STOP.
.. Setting threshold of cycles for assistance request
It is possible to set a number of cycles before the request of assistance. Once the limit is reached the next cycles will be done with fast blinking (only if
 enabled)
.. Continuous flashing light for assistance request
Once limit .. is reached the flashing light will blink also with the barrier closed to show the request of assistance.
.. Restore default settings
With this parameter it is possible to restore the default settings of the control unit. The reset will restore all the parameters of the base and advanced
menu, but doesn’t modify the learned strokes, the directions of motors and the transmitters.
Move to .. then keep pressed MENU button until the display shows 0, release the button. Press again and keep pressed MENU button, the display
will show a count down ,,…,, do not release the button until the display showns
.. Erasing of all transmitters
With this parameter it is possible to erase all the transmitters learned.
Move to .. then keep pressed MENU button until the display shows 0, release the button. Press again and keep pressed MENU button, the display
will show a count down ,,…,. Do not release the button until the display showns
.. Viewing of the memory position for a single transmitter
With the item of the menu .. it is possible to view the memory location in which a transmitter is memorized.
To perform the function, move to .. and then confirm by pressing the button MENU. Keep pressed MENU button untill the display will show
then release the button.
At this point press a button of the memorized transmitter (it does not active any command). The display shows:
 the memory location for 2 seconds, if is memorized;
 the written for 2 seconds, if is not memorized.
After 2 seconds the display returns to the screen and it will be possible to perform this function with another transmitter.
To exit from the function, press MENU button. Otherwise after 15 seconds without transmission, the control unit exits from the function and shows the
written
.. Cancellation of a single transmitter
With the item of the menu .. it is possible to delete a single transmitter from the memory.
To perform the function, move to .. and then confirm by pressing the button MENU. Keep pressed MENU button untill the display will show 0, then
release the button. Select the memory location of the transmitter. Press and keep pressed MENU button untill the display will show , then
release the button.
To exit from the function, press MENU button. If the display shows the written , there are problems with the memory (for example empty
position or disconnected memory).

ITA ENG FRA ESP DEU POR 11 / 12
6-1622245 rev.3 23/12/2016
Compatible from firmware version BIOS1BRT01
8. Display and control unit state
8.1 Normal functioning:
Safety edge intervention
Limit switches error (both opening and closing electrical limit switches busy in the same time)
Malfunctioning of photocells
Memory error
Full memory
Memory error during functions viewing memory location or cancellation of a single transmitter
8.2 Errors:
The visualization of an error on the display persists until you press the key DOWN[-] or another movement command, whatever it is
Standby - Barrier closed or after the switch on of the control unit (no in open position).
Opening phase
Closing phase
Barrier stopped by user during the opening
Barrier stopped by user during the closing
Barrier stopped by an external event (photocell, stop)
Barrier opened without automatic reclosing
Barrier opened in partial opening position without automatic reclosing
Barrier opened waiting for auto reclosing, last 10 seconds the dash will be replaced by the countdown
During the normal functioning and out from any menu, the pression of the DOWN[-] button lets you see the
number of cycles done, you will see units with dots on the bottom of display and thousand without dot,
another pression of DOWN[-] or MENU button let you to leave the cycles visualization
Visualized during the learning of transmitters
Visualized when memorized a new transmitter or at the and of a reset
Visualized when memorized a key of a transmitter already memorized
Visualized when a trasmitter is erased
Visualized during the learnign of strokes to indicate that the control unit is opening the barrier and waiting for
the command of opening mechanical stop
Visualized during the learning of strokes to indicate that the control unit is closing the gate and waiting for the
command of closing mechanical stop
Visualized during the learning of strokes if there is an intervention of safety devices
Visualized when the control unit waits a transmitter signal, during the function of viewing of the memory
location.
Visualized when the transmitter is not stored on the memory, during the function of viewing of the memory
location.
Visualized when the control unit exits from the function of viewing of the memory location for inactivity.

ITA ENG FRA ESP DEU POR 12 / 12
6-1622245 rev.3 23/12/2016
Compatible from firmware version BIOS1BRT01
GUARANTEE - In compliance with legislation, the manufacturer’s guarantee is valid from the date stamped on the product and is restricted to the
repair or free replacement of the parts accepted by the manufacturer as being defective due to poor quality materials or manufacturing defects. The
guarantee does not cover damage or defects caused by external agents, faulty maintenance, overloading, natural wear and tear, choice of incorrect
product, assembly errors, or any other cause not imputable to the manufacturer. Products that have been misused will not be guaranteed or repaired.
Printed specifications are only indicative. The manufacturer does not accept any responsibility for range reductions or malfunctions caused by
environmental interference. The manufacturer’s responsibility for damage caused to persons resulting from accidents of any nature caused by our
defective products, are only those responsibilities that come under Italian law.
9. Technical features
POWER SUPPLY AND CONSUMPTION
Power supply voltage 230 Vac - 50/60 Hz
Absorption from line (Standby) 45 mA @ 230 Vac
Standard configuration (2 couple of photocells, RX radio safety edge)
Line fuse F6.3A
MOTOR POWER SUPPLY
Number of motors 1
Motor power supply voltage 230 Vac - 50/60 Hz
Maximum power absorbed from motors 700W
ACCESSORIES POWER SUPPLY
Accessories power supply voltage 24 Vdc
Maximum current absorbed from accessories 170 mA
Maximum power absorbed from accessories 4 W
Accessories fuse F 0.5 A
Blinker output 230 Vac 60W max
Courtesy light output / open gate light 230 Vac 100W max
FUNCTIONALITY
433 MHz radio receiver Rolling code
Maximum transmitters 1000 (fino a 8000)
Safety edge input NC / 8k2
8.3 Input LED and safety devices
RED (normally on)
RED (normally on) With NC connection
RED (normally on) RED (normally on)
GREEN (normally off)
GREEN (normally off) GREEN (normally off) With NO connection
GREEN (normally off)
ALLMATIC S.r.l
32020 Lentiai - Belluno – Italy
Via dell-Artigiano, n°1 – Z.A.
Tel. [phone] – 751163 r.a. Fax [phone]
http://www.allmatic.com - E-mail: [email protected]