Alpine KTX-FPU8 User manual

Mobile
Media
Solution·s
Perfect Fit For Select 2009+ Ford F-150 Trucks
Installation Manual
Ford Trim Panel x 1
{Panel 7272)
Left Bracket x 1
{Panel 727
4)
KTX-FPU8-S
Power Harness x 1
Right Bracket x 1
{Panel 7273)
Steering Wheel Interface
Module x 1
KCX-ANTB3
Ford Antenna
Adapter
Introduction
This KTX-FPU8-S Perfect Fit installation kit is
for
Select 2009+ Ford F150 trucks. Included are
all the parts needed
to
install yourAlpine INE-Z928HD Audio Video Navigation system in Select
2009+ Ford F150 trucks. KTX-FPU8-S Perfect Fit installation kit also includes
an
interface module
that allows steering wheel remote control
of
the Alpine system. Refer
to
the individual instruction
sections
of
this manual
to
remove your vehicle's factory radio and·assemble the kit.·
Caution!
Disconnect
your
vehicle's
negative
battery
terminal
before_
the
installation
to
help
prevent
electrical
damage.
We
recommend
the
use
of
a
digital
multimeter
to
check
vehicle
wiring.
Do
not
use
a
test
light!
A
test
light
or
grounded
wire
probe
can
cause
damage
to
the
vehicle's
computer
and/or
diagnostic
systems.
Avoid
all
factory
airbag
wiring.
Airbags
can
accidentally
deploy
causing
serious
injury
or
even
death.
Notes:
• See your vehicle's instructions
for
any special tools your instaltation might require.
• Read all instructions accompanying your car stereo for proper wiring and mounting
instructions.
1

Factory Stereo Removal
1. Use a panel removal tool to carefully unsnap dash/
vent panels on eitherside of radio.
2. Remove (2) 7mm screws on top of stereo in front of
display.
3. With panel removal tool unsnapsmall panel next
to
cigarette lighter.
4. Remove (1) 7mm screw.
5. Unsnap complete stereo & AC panel.
6. Remove
(4) 7mm screws securing radio.
2

Mounting The Stereo
7. Mount the 7273 and 7274 brackets to the
Alpine head
unit using screws supplied with
kit
or reusing the screws from factory stereo,
if possible.
9. Connect the supplied Plug-and-play wiring
harness.
8. Remove hazard switch assembly, A/C
controls, cigarette lighterassembly, and sync
unit (where applicable).
10. Hook
the Yellow/Blackwire to the Foot Brake
(+)at switch above pedal
11. Hook
the Yellow/Blue wire to the Parking Brake (-)
at brake in driver kick panel
12. Secure INE-Z928HD using the
(4) 7mm
screws. Connect and install 7272 panel as-
sembly
over radio.
3

Wiring Harness Diagram
To
Foot
Brake
(+)
at
switch above pedal
To
aftermarket amplifier
F====:d/
remote turn on
To
Steering Wheel Remote
Module
Liability Disclaimer
To
Head Unit
Power Connector
To
Steering Remote
Input (Pigtail)
INE-Z928HD
Audio
Video
Navigation
System
Due
to
changes in design and manufacturing that may
occur
with your specific vehicle,
it
is important that you
do
not rely solely on vehicle information contained in this installation
manual, such as dash disassembly, wire harness, and codes. Such information should be
confirmed with the vehicle manufacturer. Alpine Electronics, Inc. and its affiliated companies
is not responsible
for
damage
that
may occur
to
you
or
your automobile during the installation
of
the Perfect Fit Kit.
Ifyou have any further questions, feel free
to
contact Alpine Tech Support at 1-800-NAV-HELP.
ALPINE ELECTRONICS OF AMERICA, INC., 19145 Gramercy Place, Torrance, CA 90501, U.S.A
ALPINE ELECTRONICS OF CANADA, INC., 777 Supertest Road, Toronto, Ontario M3J 2M9,
Canada
Do not send products
to
these addresses.
Call the toll free number
or
visit the website
to
locate a service center.
4

~
-
-
-
~
PERFECT FIT™ INSTALLATION KIT
PERFECT
I 1:?' 0 '1:::r I
S OL U T I O N S
• • KIT D' INSTALLATION PERFECT
FIT™
ALPINE ELECTRONICS OF AMERICA, INC.
www .alpine .com
DRIVING MOBILE MEDIA SOLUTIONS
r KTX-FPUS
2009-UP
FORD F-150
INSTALLATION KIT
(EXCLUDES LARIAT & NAVIGATION)
KTX-FPUS
2009-UP
FORD F-150
INSTALLATION KIT
(EXCLUDES LARIAT 8r NAVIGATION)
ffffhiLPINE e
Mobile Media Solutions

• PERFECT SHAPE AND COLOR MATCH TO OEM DASH FOR FACTORY FIT
• INCLUDES ALPINE-TO-VEHICLE HARNESS FOR PLUG-AND-PLAY INSTALLATION
• INCLUDES RETAINING CLIPS
• INSTRUCTION
MANUAL
WITH STEP-BY-STEP INSTALLATION OF
ALL
COMPONENTS
• CORRESPONDANCE PARFAITE AVEC
LA
FORME ET COULEUR
DU
TABLEAU DE BORD DE L'EQUIPEMENTIER POUR UN
ASPECT SORTIE D'USINE
• COMPREND UN HARNAIS POUR CONNECTER L'UNITE ALPINE AU VEHICULE POUR UNE INSTALLATION PRETE
A
L'EMPLOI
• COMPREND LES CLIPS DE MAINTIEN
• MANUEL D'INSTRUCTIONS DETAILLANT L'INSTALLATION PAS
A
PAS DE TOUS LES COMPOSANTS

Alpine, Alpine Mobile Media Solutions, Driving Mobile Media Solutions are registered trademarks of Alpine Electronics, Inc.
Alpine, Alpine Mobile Media Solutions, Driving Mobile MediaSolutions sont
des marques deposees d'Aipine Electronics, Inc.
MADE IN CHINA
FABRIQuE EN CHINE