Alpine KTX-FUS8 User manual

Mobile Media Solutions
Perfect Fit For Select 201 0-up Ford Fusion I
Ford Trim Panel x 1
(Panel 7344)
2010-11 Mercury Milan
KTX-FUSS
Power Harness x 1 Steering Wheel Interface
Module x1 Ford Antenna
Adapter
Left Bracket x 1
(Panel 7345) Right
Bracket x 1
(Panel 7346)
KCX-RRMFD
Radio Replacement
Module x 1
Introduction
This KTX-FUS8 Perfect Fit installation kit is for Select 2010+ Ford Fusion and 2010-11 Mercury
Milan vehicles. Included are all the parts needed to install your Alpine INE-Z928HD Audio Video
Navigation
system in Select 2010+ Ford Fusion and 2010-11 Mercury Milan vehicles. KTX-FUS8
Perfect Fit installation
kit also includes an interface module that allows steering wheel remote
control of the Alpine system. Refer to the individual instruction sections of this manual to remove
your vehicle's factory radio and assemble the kit.
Caution! Disconnect your vehicle's negative battery terminal before the Installation to
help prevent electrical damage. We recommend the use of a digital multimeter to check
vehicle wiring. Do not use a test light! A test light or grounded wire probe can cause
damage to the vehicle's computer and/or diagnostic systems. Avoid all factory airbag
wiring. Alrbags can accidentally deploy causing serious injury or even death.
Notes:
• See
your vehicle's instructions for any special tools your installation might require.
• Read all
instructions accompanying your car stereo for proper wiring and mounting
instructions.
1

Factory Stereo Removal
1. Use a Panel Removal Tool to unclip shiftertrim
bezel.
2. Open console storage. Use a Panel Removal Tool
to unsnap the trim around cup holderand shifter. Lift
away and remove.
3. Use a Panel Removal Tool
to unsnap the small +12V
accessory
power panel in front of the shifter, unplug
and remove.
4. Open
upper storage tray above radio and
remove rubberliner. Extract
(2) 8mm screws from
storage compartment. Note: On
some models
there
my be a safety strap attached to this panel.
Remove the T-20
torx screw below the passenger
airbag light
to remove panel.
5. Remove
(2) 7mm screwsfrom the top radio/
climate panel.
6. Extract
(4) 7mm screws securing the radio's mo-
tor/chassis, unplug all connectors and remove.
2

Mounting The Stereo
1. From the back side of the OEM Factory Stereo AIC
control stack, extract
(4) T-20 Torx Head screws to re-
movethe A/C control assembly. Re-attach A/C control
assembly
to the Perfect Fit Panel 7344. Remove the
clips from the factory stereo panel and attach them
to
panel7344.
•
2. Attach panels 7345 and 7346 to the Alpine
head unit using
the supplied screws (that come
with the head unit).
3. Plug in the supplied radio harnessesand steer-
ing wheel controls. Run Bluetooth
mic & GPS
antenna, and install
foot brake and parking brake
wires.
4. Connect and mount
the stereo in the dash. (The
main kit panel mounts
to the dash over the stereo).
Re-connect the Factory
HVAC & misc.controls.
Panel 7344 mounts
to the dash over the radio.
3

Wiring Harness Diagram ,
To aftermarketamplifier
remote turn on
to-=========:
To Foot Brake(+) at
switch above pedal Yellow/Black
Steering Wheel
Remote Module
Steering Wheel Controls
Steering Wheel Control Operation
(when
vehicle Is equipped)
1. Volume Down
2. Seek/Track Down
3. Not Used
4.
Not Used
5. Volume
Up
6. Seek/Track Up
7. Source
8.
Not Used
Liability Disclaimer
To Head Unit
PowerConnector
INE·Z928HD
Audio
Video
Navigation
System
Factory OEM Aux
Port (Below Radio)
To Steering Remote Input
(Pigtail on Head Unit)
MEDIA
Due to changes in design and manufacturing that may occur with your specific vehicle, it
is important that you do not rely solely on vehicle information contained in this installation
manual, such as dash disassembly, wire harness, and codes. Such information should be
confirmed
with the vehicle manufacturer. Alpine Electronics, Inc. and its affiliated companies
is
not responsible for damage that may occur to you or your automobile during the installation
of the Perfect Fit Kit.
If you have any further questions, feel free to contact Alpine Tech Support at 1-800-NAV-HELP.
ALPINE ELECTRONICS OF AMERICA, INC., 19145 Gramercy Place, Torrance, CA 90501, U.S.A
ALPINE ELECTRONICS OF CANADA, INC., 777 Supertest Road, Toronto, Ontario M3J 2M9,
Canada
Do
not send products to these addresses.
Call the toll free number
or visit the website to locate a service center.
4

Mobile
Media
Solutions
PERFECT
FIT™
INSTALLATION KIT
,
~ERFECf
..
·
ao~)~~N
S
KIT D' INSTALLATION PERFECT
FIT™
.
' .

ALPINE
ELECTRONICS
OF
AMERICA,
INC.
www
.alpine.com
DRIVING MOBILE
MEDIA
SOLUTIONS
1 KTX-FUSS
L
2010-UP
FORD FUSION
INSTALLATION
KIT
(NON-NAVIGATION)
KTX-FUSS
2010-UP
FORD FUSION
INSTALLATION KIT
(NON-NAVIGATION)
Mobile
Med
ia
Solutions

• PERFECT SHAPE
AND
COLOR MATCH TO OEM DASH FOR FACTORYFIT
•INCLUDES
ALPINE-TO-VEHICLE HARNESS FOR PLUG-AND-PLAYINSTALLATION
• INCLUDESRETAINING CLIPS
• INSTRUCTION
MANUAL
WITH STEP-BY
.STEP INSTALLATION
OF
ALL
COMPONENTS
• CORRESPONDANCE PARFAITEAVEC
LA
FORME
ET
COULEUR DU TABLEAU DE BORD DE L'EQUIPEMENTIER POUR UN
ASPECTSORTIE D'USINE
• COMPREND UN HARNAISPOUR CONNECTER L'UNITEALPINE
AU
VEHICULE POUR UNE INSTALLATION
PR~TE
A
L'EMPLOI
• COMPREND LES CLIPS DEMAINTIEN
•
MANUEL
D'INSTRUCTIONS DETAILLANT L'INSTALLATION PAS
A
PAS DETOUS LES COMPOSANTS
Mobile
Media
Solutions