Alpine X109-WRA User manual

Jeep Wrangler
WRANGLER 1/15
Jeep Wrangler
X109-WRA 9” Restyle
In-Dash System
Installation Manual
Model: Wrangler
Model Year: 2011-UP
Introduction
Design and specifications are subject to change without notice for improvement.
To Ensure Safe Use, Always Follow These Precautions
The installation of this product requires specialized skills and experience. We recommend that you have the
product installed by an Alpine authorized dealer.
Before you use this product, be sure to carefully read this installation manual and the separate user's manual
so that you can use the product correctly. Alpine Electronics bears no responsibility for problems that arise as
a result of failure to follow the instructions in the manuals.
This manual includes a number of symbols that are intended to help you use the product safely, to prevent
harm to you and others, and to protect against damage to property. These symbols and their meanings are
listed below. Make sure you fully understand these symbols before you begin reading the main text.
Explanations of Injury and Damage That May Result from Incorrect Use
Warning Ignoring the content marked by this indication and using the product incorrectly is
expected to lead to death or serious injury.
Caution Ignoring the content marked by this indication and using the product incorrectly is only
expected to lead to injury or property damage.
Jeep Model Year
Wrangler 2011 - UP
* The specified vehicles have been tested and have met compatibility specs at the time of testing. Compatibility is
not guaranteed if the manufacturer has made production changes to the listed vehicles above.
Warning: Before you begin wiring, remove the ground wire from the negative
terminal of the battery. Failing to do so can lead to electric shock, injury or damage
to equipment.

Jeep Wrangler
WRANGLER 2/15
Types of Precautions
Forbidden
Indicates actions that are forbidden
(must not be performed)
Mandatory
Indicates actions that are
mandatory (must be performed)
Forbidden
Indicates that disassembly is
forbidden.
Marks content that should receive
your full attention.
Warning
Do not disassemble or modify the product. Doing so could lead to an accident, re,
or electric shock.
Forbidden
Store screws and other small objects where small children cannot reach them. If one of these
small objects is swallowed, consult with a doctor immediately.
When replacing fuses, be sure to use fuses with the specied current rating. Failing to do so could
lead to an accident or re.
Forbidden Mandatory
Only connect the product to a 12 VDC negative ground car. Failing to do so could lead to
an accident or re.
Mandatory
Before you begin wiring, remove the ground wire from the negative terminal of the battery.
Failing to do so could lead to electric shock or injury.
Do not cut the insulation on a cord and take power from another device. Doing so could
lead to re or electric shock.
Forbidden
Do not install the product in a location where it will obstruct the driver’s forward view;
interfere with the operation of the steering wheel, gearshift, or the like; or pose a
threat to passengers. Doing so could lead to an accident or injury. Forbidden
When making a hole in the vehicle body, be careful to avoid damaging pipes, the fuel tank,
electrical wiring, and the like. This kind of damage could lead to an accident or re.

Jeep Wrangler
WRANGLER 3/15
When installing and grounding the product, do not use any of the bolts or nuts of the
steering wheel, brakes, fuel tank, or the like. Doing so could make the brakes stop working
or lead to re. Forbidden
Do not install the product near the passenger-side airbag. Doing so could interfere with the
operation of the airbag and lead to an accident or injury.
Forbidden
Bundle cords so that they don’t interfere with driving. Wrapping cords around the steering
wheel, gearshift, brake pedal, or the like, could lead to an accident or damage equipment.
Caution
Connect the product properly according to the instructions. Failing to do so could lead
to re or an accident.
Forbidden
Do not sandwich cords between the seat railing or allow them to touch protrusions.
Resulting breaks or shorts could lead to electric shock or re.
Do not block vents or heat sinks. Doing so could lead to re or damage equipment.
Use the accessories according to the instructions, and attach them securely.
Failing to do so could lead to an accident or damage equipment.
Forbidden
Do not install the product where it may be exposed to water or in a place with high levels
of humidity or dust. Doing so could lead to re or damage equipment.
Forbidden
The installation and wiring of this product requires specialized skills and experience.
Have the product installed by an Alpine authorized dealer.

Jeep Wrangler
WRANGLER 4/15
Tools Required
Panel Removing Tool 7mm Sockets #2 Phillips Screwdriver
10mm Sockets Extension Ratchet
Air Saw Wire Cutters
Accessory List
Installation Kit Parts (G-KTX-X109D-WRA)
X109-WRA Radio Dash Bezel Key Harness Side Mounting Brackets
Microphone GPS Antenna Bracket Rear Support Bracket

Jeep Wrangler
WRANGLER 5/15
Accessory List
Head Unit Box Parts (X109D)
X109D DVD/Display Unit X109D Source Unit USB Extension Cable
AUX/Pre Out Harness GPS Antenna Documents
Alpine
Registration Card QRG Navigation
OM QR Card
Direct Camera Adapter Display Cable HDMI Cable
Source Unit HDMI Bracket DVD/Display HDMI Bracket (8) 8mm Screws
iDatalink Maestro Box Parts (ALP-MRR2/ALP-HRN-WRA2)
Maestro Flashing Cable Antenna Adapter iDatalink Maestro Module
Main Harness SAT Radio Antenna Adapter OEM USB Adapter

Jeep Wrangler
WRANGLER 6/15
Component Locations
IMPORTANT: Follow the recommended component location shown below. Failure to do so, will result in poor
GPS performance.
Jeep
Jeep SINCE 1941
GPS Antenna Location
BT Microphone
iDatalink Maestro Module
SAT-Radio Tuner
(Sold Separately)
GPS Antenna Installation
IMPORTANT: Follow the GPS antenna installation procedure shown below. Failure to do so will result in poor
GPS performance.
Wire Hook Wire HookCable bundle here
Attach the GPS antenna
bracket on the left side
of the instrument panel
using the 7mm factory
screw.
Peel the plastic layer off from the
double sided tape on the GPS
antenna and place the GPS
antenna on the center of the GPS
antenna bracket with the cable
facing forward.

Jeep Wrangler
WRANGLER 7/15
Factory Unit Disassembly Process
1Remove the rubber cover from the top center
storage area and extract (1) 7mm screw.
3Remove the window switch pod using a panel
removing tool and extract (1) 7mm screw.
5Extract (4) 7 mm screws and remove the factory
radio.
2Remove the knee cover panel and extract (2) 7mm
screws located to the right and left sides of the
steering wheel column.
Right side of
steering wheel
column.
Left side of
steering wheel
column.
4Remove the dash panel.
6Extract (2) 7 mm screws from the factory radio
bracket and remove it.
2

Jeep Wrangler
WRANGLER 8/15
Programming the iDatalink Maestro Module
1INSTALL THE WEBLINK PLUG-IN
Go to:
idatalinkmaestro.com/plugin and follow the installation steps.
Review the System Requirements before installing.
If the plugin is already installed, the caution, “The plugin is already
installed” appears. Please skip to step 2.
3 CONNECT YOUR MAESTRO MODULE
Use the included USB cable to connect your Maestro module to your
PC.
5 PROGRAM YOUR MODULE
Follow the programming steps for your vehicle.
2REGISTER A WEBLINK ACCOUNT
Go to:
idatalinkmaestro.com/register and complete the registration process.
A conrmation email will be sent to you requiring validation.
For existing customers, click log in.
4 LOG INTO WEBLINK
Go to:
idatalinkmaestro.com/login.
Enter your username and password, then click OK.
6 Once Programing is complete “FLASHING
COMPLETED!” will be displayed.
Proceed to the next page to complete installation.

Jeep Wrangler
WRANGLER 9/15
Installation Instructions
2Remove the vents from the radio section on the
OEM dash panel by pressing down on the lock tab
and turning right. Mount vents on to the X109-WRA
bezel.
Lock tab
Rear view
4Mount the microphone as illustrated and run the
cable to the radio cavity.
6Attach the Maestro to the main harness.
1The factory dash panel needs to be trimmed to
allow the new X109-WRA bezel to fit into place.
Remove the highlighted area by cutting along the
dashed line.
3Use a cutting tool to trim the highlighted area
shown below.
5Plug the OBDII connector on to the OBDII port
below the driver side dash and run the extension to
the radio cavity.

Jeep Wrangler
WRANGLER 10/15
Mounting Brackets
IMPORTANT: During the research and development of this product it was discovered that mounting tolerance
may vary from the vehicle’s trim level to year built. We have added a 1mm tolerance to the mounting brackets
to compensate for such variance in mounting tolerance. Use the guides below as reference if there are any
required adjustments.
Adjust the rear bracket as needed when the top or bottom is protruding or not flushed.
Adjust the side brackets as needed when either side is protruding or not flushed.