Alvarado EDC User manual

Alvarado Manufacturing Company, Inc.
12660 Colony Street, Chino, CA 91710
Telephone: [phone]
Fax: [phone]
[email protected]
www.alvaradomfg.com
PUD1535R5-5
Installation and Maintenance Instructions
(APPLICABLE TO ALL EDC MODELS)
EDC
WAIST HIGH SECURITY TURNSTILE

EDC Installation and Maintenance Instructions
Page 2 For assistance: [email protected] [phone] PUD1535R5-5
The following symbols are used throughout the manual to highlight important information and potential risks when
installing, servicing or using the turnstiles covered in this manual.
WARNING This symbol is used in this manual to warn installers and operators of potential harm. Please
read these instructions very carefully.
This symbol is used in this manual to designate potential conditions that may pose a risk to
pedestrians, personnel, property, and equipment Please read these instructions very carefully.
This symbol is used in this manual to designate useful information for the installer and operator.
Please read these instructions.
Safety Icons
Contents
For questions, please contact Alvarado at [phone], Monday – Friday 7:00 am to
4:30 pm PST. Please read this manual completely before installing or operating the product.
Contents. ......................................................................................................................................................................... 2
Safety Icons..................................................................................................................................................................... 2
Safety Precautions. ......................................................................................................................................................... 3
CE Compliance and Standards. ...................................................................................................................................... 3
Installation Tools. ............................................................................................................................................................. 3
Parts List.......................................................................................................................................................................... 4
Common Terms. .............................................................................................................................................................. 4
Before You Begin............................................................................................................................................................. 5
Site Preparation............................................................................................................................................................... 5
Slab Requirements. .................................................................................................................................................. 5
Space Requirements. ............................................................................................................................................... 5
Installation Instructions.................................................................................................................................................... 6
Anchoring the Turnstile. ............................................................................................................................................ 6
Electrical Wiring Instructions. .......................................................................................................................................... 7
Primary Power Wiring. .............................................................................................................................................. 7
Access Control Wiring............................................................................................................................................... 7
10-7821 Turnstile Control Board Layout. .................................................................................................................. 8
10-7821 Terminal Descriptions.................................................................................................................................. 9
Operations and Functionality. .........................................................................................................................................11
Passage Modes. ......................................................................................................................................................11
Loss-of-Power Operation (Electric Models Only).....................................................................................................11
Drop-Arm (Optional).................................................................................................................................................11
User Notication Lights (Optional). ..........................................................................................................................11
Local Battery Counter (Optional). ........................................................................................................................... 12
Key Override. .......................................................................................................................................................... 12
Post-Installation Functions Check........................................................................................................................... 12
Cleaning and Maintenance............................................................................................................................................ 13
Maintenance Schedule. .......................................................................................................................................... 13
Exterior Maintenance. ............................................................................................................................................. 14
Interior Maintenance. .............................................................................................................................................. 15
Troubleshooting............................................................................................................................................................. 18
Appendix A - Plan, Elevation and Footprint Drawings. .................................................................................................. 21
EDC (27" Length).................................................................................................................................................... 21
EDC-E (Extended). ................................................................................................................................................. 22
EDC-BN (Bullnose). ................................................................................................................................................ 23
EDC-EBN (Extended Bullnose). ............................................................................................................................. 24
Appendix B - Replacement Parts Kits. .......................................................................................................................... 25
Appendix C - 10-7822 Turnstile Control Board Layout and Terminal Descriptions........................................................ 29
Revision History............................................................................................................................................................. 32
NOTE
CAUTION

EDC Installation and Maintenance Instructions
PUD1535R5-5 For assistance: [email protected] [phone] Page 3
WARNING
• Use only skilled individuals to install and service the turnstile.
• The turnstile is not a toy. Do not allow children to play on or near the turnstile.
• Follow a proper maintenance schedule using skilled individuals.
• Do not operate the turnstile if it has been damaged or is functioning incorrectly. Have the
turnstile repaired by a skilled service person before placing back in use.
• Do not modify or alter the turnstile.
• Use only Alvarado parts when repairing or maintaining the turnstile.
• Ensure that all users are properly trained.
• Test the turnstile on a daily basis
SAVE THESE INSTRUCTIONS
After installation and adjustment, the installer is responsible for providing the owner or site manager with these
instructions.
Safety Precautions
CE Compliance and Standards
This page denes the product labels required for compliance with LA Electrical Testing Laboratory and CE standards.
CE Standards:
a. Label (1) the Outlet Specication.
~240V, 1800W
b. Label (2) the Fuse Specication.
F1.0A, 240V
c. Label (3) the Warning, Risk of Electric Shock.
DANGER
d. Label (4) the Caution, Risk of Danger.
DANGER
LA Electrical Testing Laboratory Standards:
a. Label (1) the Outlet Specication.
~120V, 1800 Watts Max.
b. Label (2) the Fuse Caution.
CAUTION: For continued protection,
against risk of re or shock, replace with
the same type and rating fuse.
c. Label (3) the Warning, Risk of Electric Shock.
WARNING: For continued protection,
against risk of re or shock, replace with
the same type and rating fuse.
• Hammer Drill
• 1" Concrete Drill Bit
• Shop Vac
• 9/64" Allen Wrench
• #2 Phillips Head Screwdriver
• Torque Wrench (ft-lbs)
• 15/16" Socket
• Hammer
• Tape Measure
• Chalk
• Washer Shims
• 3mm Flat Head Screwdriver
(Required for electric models only)
Installation Tools

EDC Installation and Maintenance Instructions
Page 4 For assistance: [email protected] [phone] PUD1535R5-5
This product is shipped with the required installation hardware. Make sure that no parts are missing and/or damaged
before beginning installation. If parts are missing and/or damaged, please stop the installation and contact Alvarado. If
additional copies of the installation instructions are required, please visit www.alvaradomfg.com.
Keys are taped to the turnstile arms. Be sure to locate the keys
before discarding any shipping materials.
Parts List
Common Terms
NOTE
EDC Waist High Security
Turnstile*
*EDC (27" Length) model shown
Also included:
Hardware (per turnstile)
•Threaded Rods (Qty 2)
•Rod Cups (Qty 2)
•Concrete Anchors (Qty 2)
Keys (per turnstile)
•Turnstile Lid Keys (Qty 2)
•Key Override Keys (Qty 2)
Activation (unlocking) of electric models is accomplished by providing a
momentary dry contact signal of .5 to 1 second to the appropriate location
on the turnstile control board. Activations are not bu󰀨ered. After an
activation is received, the turnstile will not accept another activation until the
turnstile is rotated or the automatic turnstile relock period has expired.
Turnstile arms rotate in a clockwise direction when viewed looking down
from the non-arm side of the cabinet.
Turnstile arms rotate in a counterclockwise direction when viewed looking
down from the non-arm side of the cabinet.
Upon loss of power, the turnstile arms cannot be rotated in either direction.
Upon loss of power, the turnstile arms rotate freely in both directions.
All EDC turnstiles come with key overrides located on the underside of the
front panel. Key overrides are used to toggle between free passage and
controlled passage modes (electric models only). There is one key override
provided for each rotation direction.
When the turnstile receives an activation (unlock signal), the user is allowed
a set time to pass through the turnstile before it automatically relocks. The
factory default setting is 20 seconds. The turnstile control board allows the
user to change this setting to 5, 10, 15 or 20 seconds.
The arms are locked in the home position. Upon receipt of an activation
from an access control system, the turnstile unlocks in the appropriate
direction allowing a single passage. The arms relock after the user has
passed through the turnstile or when the automatic turnstile relock period
has expired. Controlled Passage mode can be either single direction or
bidirectional.
An authorization signal is not required for a user to pass through the
turnstile. Either rotation direction can be set to Free Passage mode using
the key overrides located on the underside of the cabinet.
The turnstile arms are locked and remain locked even if valid credentials are
presented to the access control system.
Activation
Clockwise Rotation (CW)
Counterclockwise Rotation (CCW)
Fail-Lock
Fail-Safe
Key Override
Automatic Turnstile Relock
Controlled Passage Mode
Free Passage Mode
No Passage Mode

EDC Installation and Maintenance Instructions
PUD1535R5-5 For assistance: [email protected] [phone] Page 5
The EDC product line of waist high security turnstiles include manual and electric models with varying cabinet sizes
and styles. This manual focuses on the EDC (27" length) model for the basis of instruction; however, most steps are
identical across models. Any di󰀨erences will be called out as applicable. Instructions apply to the following models:
Use only skilled technicians for site preparation and installation of the turnstile using Alvarado’s instructions. Refer to
the footprint and plan drawings [Figures 1A & 1B] to determine the installation location and conduit requirements.
See Appendix A for other models.
The following must be taken into consideration when selecting the installation location:
• Use a level solid concrete pad with a minimum thickness of 4" (101.5mm). Ensure concrete pad extends a
minimum of 5" (127mm) from all sides of the turnstile footprint.
• Do not install the turnstile on asphalt.
• Stub up conduit in accordance with local electrical codes.
The following must be taken into consideration when determining
space requirements:
• Always verify the layout of the turnstile(s) before installation.
• There must 2" (50.8mm) of clearance between the turnstile arm
and the adjacent turnstile or barrier.
EDC (27" Length) Footprint
EDC (27" Length) Plan View
EDC (27" Length) EDC-E (Extended) EDC-BN (Bullnose) EDC-EBN (Extended Bullnose)
See Appendix A for footprint and dimension
drawings for other models.
Before You Begin
Site Preparation
NOTE
Fig. 1A
25.3
(644)
27
(686)
9.50
(241)
Fig. 1B
Slab Requirements
Space Requirements
2.6
(66)
3.9
(99)
1.2
(30)
5
(127.00) 7.9
(201)
12.3
(312)
2.1
(53)

EDC Installation and Maintenance Instructions
Page 6 For assistance: [email protected] [phone] PUD1535R5-5
1. Place the turnstile in the desired location.
2. Using a lid key, unlock and open the turnstile lid.
There is a lid lock on each side of the turnstile.
3. Using a 9/64” Allen wrench, remove the four (4)
transformer screws [Figure 2].
4. Slide the transformer/junction box to the side to gain
access to the welded post anchor tube beneath
[Figure 3].
5. Route primary power wiring from the appropriate
conduit opening into the turnstile [Figure 3].
6. To mark the anchor holes, you will need to insert a
chalked threaded rod down the post anchor tubes. To
help center the threaded rod in the post anchor tube,
use a rod cup as shown in [Figure 4].
7. Chalk the bottom of the shaft rod. Run the chalked
threaded rod down a post anchor tube and gently tap
the rod on the concrete to mark the anchor’s center
location. Repeat for other post anchor tube.
8. Move the turnstile to the side.
9. Using a hammer drill tted with a 1” concrete bit, drill
each anchor hole to a depth of 3” (76.2mm).
10. Insert anchors into the drilled holes with the threaded
ends down. If needed, use a hammer to tap the
anchor into place. Ensure that the anchors are ush
with the concrete oor [Figure 5].
11. Return the turnstile to the install location, ensuring the
anchors are centered in the post anchor tubes.
Installation Instructions
Transformer Screws
Rod Cup & Threaded Rod
Inserting Anchors
Threaded Side
Down
Threaded
Rod
Rod
Cup
Flush with
Concrete
Accessing the post anchor tubes
Slide
Anchor
Tube
Conduit Openings
Anchor
Tube
Transformer/
Junction Box
Fig. 2
Fig. 4
Fig. 5
Fig. 3
Vacuum debris from the anchor holes before
installing the anchors. If the holes are not clear of
debris, the anchors may not tighten correctly.
NOTE
Anchoring the Turnstile
Transformer

EDC Installation and Maintenance Instructions
PUD1535R5-5 For assistance: [email protected] [phone] Page 7
12. Insert a threaded rod & cup assembly down a post anchor tube and into the anchor. Repeat with the other
threaded rod & cup assembly and post anchor tube.
13. Check that the turnstile is level and does not rock. If the turnstile rocks, shim as necessary using washer shims.
14. Using a torque wrench (ft-lbs.) and 15/16” socket, torque the threaded rods to 80 ft.-lbs.
15. Return the transformer/junction box to its mounting location. Using a 9/64” Allen wrench, tighten the four (4)
transformer/junction box screws.
For manual (non-electric) turnstiles, this concludes the installation.
16. Make sure primary power is turned OFF.
17. Make sure the junction box switch is set to OFF.
18. Using a #2 Phillips head screwdriver, remove the two
(2) junction box cover screws and set the cover aside
[Figure 6].
19. Locate the power wires inside the junction box.
20. Run the primary power wires through the appropriate
knock-out on the junction box [Figure 6].
21. Connect the power wires according to your power
conguration [Table 1A & 1B].
22. Secure the wires and wire nuts.
23. Verify that all contacts are secured and isolated from
any possible shorts.
24. Tuck excess wire into the junction box.
25. Using a #2 Phillips screwdriver, re-attach the junction
box cover.
Electrical Wiring Instructions
Primary Power Wiring
Anchoring the Turnstile (cont.)
Junction Box (110V Version Shown)
110 VAC Connections 220 VAC Connections
Fig. 6
Table 1A Table 1B
Use a licensed electrician for the following steps,
and adhere to all applicable local codes.
WARNING
Junction Box Primary Power
Green Screw Green Wire
Gold Screw Black Wire
Silver Screw White Wire
Junction Box Primary Power
Green/Yellow Screw Green/Yellow Wire
Gold Screw Blue Wire
Gold Screw Brown Wire
26. Using a 3mm at head screwdriver, connect access control wiring to the turnstile control board's J3 and/or J7
terminal connectors [Figure 7]. Refer to the 10-7821 Turnstile Control Board Layout and Terminal Descriptions
sections on the following pages for more information.
For electric turnstiles, this completes the installation. Proceed to the Operations and Functionality section on
page 11, and the Post-Installation Functions Check section on page 12.
For a DC primary power connection, run 13.5VDC to the J4 connector on the turnstile control board.
NOTE
Access Control Wiring
Cover
Screws

EDC Installation and Maintenance Instructions
Page 8 For assistance: [email protected] [phone] PUD1535R5-5
10-7821 Turnstile Control Board Layout
Refer to Appendix C for 10-7822 turnstile control board used in conjunction with the drop-arm option.
NOTE
10-7821 Turnstile Control Board
Fig. 7
LEGEND
Item Name
A CCW Test Activation Switch (SW7)
B Access Control Activation - CCW
C Access Control Activation - CW
D CW Activation Test Switch (SW6)
E DIP Switches (SW4)
F Green LED
G Fire Alarm System Connection - CW
H Fire Alarm System Connection - CCW
Clockwise Fail Lock
Counterclockwise Fail Lock
Timer - See Chart to the Right
Timer - See Chart to the Right
Feedback Pulse - 100ms
JS3 LED Option
STD Optics
Clockwise Fail Safe
Counterclockwise Fail Safe
Timer - See Chart to the Right
Timer - See Chart to the Right
Feedback Pulse - 300ms
JS2 LED Option
1st Sensor Optics
SW4 Layout
1 2 3 4 5 6 7 8
ON DIP
A
CG
D
E
J18 J3 J7
J4
J10 J9
J5
J8
J2
SW4
F
X 5 R G Y X 5 R G Y CCW CCW CW CW
CCW CW
CCW-CNT CW-CNT OPTICAL SENSORS CNT-RESET
J19
SW3
J11
BH
ACC GND REJ CLS GND OPN CNT COM ACC GND REJ CLS GND OPN CNT COM
Automatic turnstile relock Setting
(Positions T3 and T4)
T3 T4
5 seconds
10 seconds
15 seconds
20 seconds (Default)
ON ON
ON OFF
OFF ON
OFF OFF
Automatic Turnstile Relock Setting Switches
JP1
JP2
Fig. 7A
Fig. 7B
SW7 SW6
NOTE Default DIP switch settings pictured
above are for Fail-lock/Fail-safe
congurations.
AUX (Fire Alarm Input - N.O.) AUX (Fire Alarm Input - N.C.)

EDC Installation and Maintenance Instructions
PUD1535R5-5 For assistance: [email protected] [phone] Page 9
10-7821 Terminal Descriptions
Refer to the 10-7821 Turnstile Control Board Layout as needed.
NOTE
BOARD NAME DESCRIPTION EXPLANATION
J18 CCW Solenoid VDC wire connection -
CCW Direction
Connection for counterclockwise solenoid. Universal polarity.
J18 CCW Solenoid VDC wire connection -
CCW Direction
Connection for counterclockwise Solenoid. Universal polarity.
J18 CW Solenoid VDC wire connection -
CW Direction
Connection for clockwise solenoid. Universal polarity.
J18 CW Solenoid VDC wire connection -
CW Direction
Connection for clockwise solenoid. Universal polarity.
SW7 CCW
Entry
Activation
Test
Button
Allows user to test turnstile activation -
CCW Direction
Depressing button simulates input to J3 ACC, “Entry Accept”. If
turnstile solenoid “res” after depressing button AND re-locks after a
single rotation of the arms or upon time out, the turnstile is functioning
correctly in the counterclockwise direction.
J3 ACC
Entry
Accept
“Card Authorized” input connection from
the access control system -
CCW Direction
This connection is used to tell the turnstile to unlock. The turnstile
control board will accept a normally-open dry-contact signal of .5
seconds to 1 second from the access control system and allow one
rotation of the arms before re-locking.
J3 GND
Ground
Ground wire connection from the access
control system - CCW Direction
Ground wire connection position for ACC and REJ contact signal.
J3 REJ
Entry
Reject
“Card Reject” input connection from the
access control system - CCW Direction
This connection is used to tell the turnstile to remain locked. The
access control system has determined that the card presented is
unauthorized for entry.
J3 CLS
Close
Passage
Connection for placing turnstile in locked
“CLOSED” status -
CCW Direction
Providing a continuous dry-contact signal at this terminal places the
turnstile in a locked “CLOSED” mode. This mode overrides the access
control system operation. If status lights are installed (Location J19) the
red light will be illuminated continuously.
J3 GND
Ground
Ground wire connection for “OPN/CLS” lane
control - CCW Direction
Ground wire connection for “OPN/CLS” passage control.
J3 OPN
Open
Passage
Connection for placing turnstile in “OPEN”
status - CCW Direction
Providing a continuous dry-contact signal at this terminal places the
turnstile in an “OPEN” mode. Typically, this terminal is used to connect
the re alarm system (normally open type) when the turnstile is
congured for counterclockwise rotation in the exit direction.
J3 CNT
Passage
Count
Conrmation signal upon turnstile rotation -
CCW Direction
Outputs a dry contact upon rotation of the turnstile. This feature can
be used to output a “count” signal to an external system such as
Alvarado’s GateWatch or to provide feedback to the access control
system that a turnstile rotation has taken place.
J3 COM
Passage
Count
Conrmation signal upon turnstile rotation -
CCW Direction
Common dry contact connection for CNT count signal output. See J3
CNT description.
J10 X5RGY-
CCW
Connection for Activation Lights -
CCW Direction
Connection for JS2 and JS3 activation lights.
J9 X5RGY-
CW
Connection for Activation Lights -
CW Direction
Connection for JS2 and JS3 activation lights.
J7 ACC
Entry
Accept
“Card Authorized” input connection from
the access control system - CW Direction
This connection is used to tell the turnstile to unlock. The turnstile
control board will accept a normally-open dry-contact signal of .5
seconds to 1 second from the access control system and allow one
rotation of the arms before re-locking.
J7 GND
Ground
Ground wire connection from the access
control system - CW Direction
Ground wire connection position for ACC and REJ contact signal.
J7 REJ
Entry
Reject
“Card Reject” input connection from the
access control system - CW Direction
This connection is used to tell the turnstile to remain locked. The
access control system has determined that the card presented is
unauthorized for entry.
J7 GND
Ground
Ground wire connection for “OPN/CLS” lane
control - CW Direction
Ground wire connection for “OPN/CLS” passage control.
J7 CLS
Close
Passage
Connection for placing turnstile in “OPEN”
status - CW Direction
Providing a continuous dry contact at this terminal places the turnstile
in a locked “CLOSED” mode. This mode overrides the access control
system operation. If status lights are installed (Location J19) the red
light will be illuminated continuously.

EDC Installation and Maintenance Instructions
Page 10 For assistance: [email protected] [phone] PUD1535R5-5
10-7821 Terminal Descriptions (cont.)
BOARD NAME DESCRIPTION EXPLANATION
J7 OPN
Open
Passage
Connection for placing turnstile in
“OPEN” status - CW Direction
Providing a continuous dry-contact signal at this terminal places the
turnstile in an “OPEN” mode. Typically, this terminal is used to connect
the re alarm system (normally open type) when the turnstile is
congured for clockwise rotation in the exit direction (default).
J7 CNT
Passage
Count
Conrmation signal upon turnstile
rotation - CW Direction
Outputs a dry-contact signal upon rotation of the turnstile. This feature
can be used to output a “count” signal to an external system such as
Alvarado’s GateWatch or to provide feedback to the access control
system that a turnstile rotation has taken place.
J7 COM
Passage
Count
Conrmation signal upon turnstile
rotation - CW Direction
Common dry-contact signal for CNT count signal output. See J3 CNT
description.
SW6 CW Entry
Activation
Test Button
Allows user to test turnstile activation -
CW Direction
Depressing button simulates input to J7 ACC, “Entry Accept”. If
turnstile solenoid “res” after depressing button AND re-locks after a
single rotation of the arms or upon time out, the turnstile is functioning
correctly in the clockwise direction.
J2
CCW-CNT Output of contact closure upon turnstile
rotation – CCW Direction
Single throw, relay output for connection to Alvarado battery-powered,
digital counter.
J8 CW-CNT Output of contact closure upon turnstile
rotation - CW Direction
Single throw, relay output for connection to Alvarado battery-powered,
digital counter.
J5 Optical
Sensors
Connection for sensors The turnstile control board uses input from the sensors to monitor
rotation of the arms.
J11 CNT-
RESET
Connection for counter-reset key switch Normally-open dry-contact connection if counter wires are attached
to J2 and/or J8 connections. A 2-position electrical key switch is
connected here to provide a reset to the individual counters.
SW3 Reset
counters
Local-Battery Counter-Reset Switch If counter wires are attached to the board (J2 and J8), depressing this
button will reset the counters. If two counters are installed and wired,
both counters will be reset.
J19 Connection for EL function light board If red/green status lights are used, the green light signies that the
turnstile is ready to accept an activation for the direction shown.
When the CLS and GND connection is closed, the red light will be
illuminated and signies that the turnstile will not accept an activation.
Refer to description for CLS on J3 and J7.
J4 Power
Input
Connection for low voltage power The turnstile control board will accept 10 VAC or 13.5 VDC power.
If primary power is not run to the turnstile, low-voltage power is
connected here and the green ground wire must be grounded to the
chassis.
Sets solenoid control for the clockwise direction in fail lock
conguration. Power is applied to solenoid upon activation
signal to release lock arm for rotation.
CWFL FS Sets solenoid control for the clockwise direction in fail
safe conguration. Power is applied to solenoid for locked
condition and removed upon activation signal to release lock
arm for rotation.
Sets solenoid control for the counterclockwise direction in
fail lock conguration. Power is applied to solenoid upon
activation signal to release lock arm for rotation.
CCWFL FS Sets solenoid control for the counterclockwise direction
in fail-safe conguration. Power is applied to solenoid for
locked condition and removed upon activation signal to
release lock arm for rotation.
Adjusts automatic turnstile relock. See Figure 7 for
settings.
T3 T3ON Adjusts automatic turnstile relock. See [Figure 7] for
settings.
Adjusts automatic turnstile relock. See Figure 7 for
settings.
T4 T4ON Adjusts automatic turnstile relock. See [Figure 7] for
settings.
Sets Length of time of contact closure on CNT and COM
feedback to 100ms.
100 FBPL Sets Length of time of contact closure on CNT and COM
feedback to 300ms.
Set switch to left when using Red/Yellow/Green activation
lights.
JS3 JS2 Set switch to right when using Red/Green activation lights.
Sets operation to standard optical sensor conguration for
passage feedback after second sensor detection.
STD ROFP Sets operation to custom optical sensor conguration for
passage feedback on rst sensor detection.
Congures OPN terminals as normally open (N.O.).
OPN inputs are used for re alarm / free passage modes.
AUX AUX Congures OPN terminals as normally closed (N.C.).
OPN inputs are used for re alarm / free passage modes.
SW4 Layout
LEFT / OFF Switch
Position
Switch
Position RIGHT / ON

EDC Installation and Maintenance Instructions
PUD1535R5-5 For assistance: [email protected] [phone] Page 11
Passage Modes
Operations and Functionality
Controlled Passage - The arms are locked in the home position. Upon receipt of an authorization signal
from an access control system, the turnstile unlocks in the appropriate direction allowing a single passage.
The arms re-lock after the user has passed through the turnstile, or when the automatic turnstile relock
period has been reached. Controlled passage can be either single direction or bidirectional.
Free Passage - An authorization signal is not required for a user to pass through the turnstile. Either rotation
direction can be set to free passage using the key overrides located on the underside of the cabinet.
No Passage - The turnstile arms are locked and remain locked even if valid credentials are presented to the
access control system.
The turnstile can be congured to operate in one of two ways during a loss-of-power event:
Fail-Lock - The turnstile arms remain locked in both directions. In the power o󰀨 condition, passage may be
allowed using the key overrides.
Fail-Safe -The turnstile arms rotate freely in both directions.
The horizontal turnstile arm drops down to provide a clear passageway upon loss of power or receipt of a re alarm
input located on the turnstile control board.
When the re alarm signal is removed, the drop arm must be moved back to the horizontal position manually.
Free Passage - The turnstile arms are unlocked and rotate freely.
No Passage - The turnstile arms are locked.
Electric turnstiles may be congured for any combination of the following passage modes:
Manual (Non-Electric) turnstiles may be congured for any combination of the following passage modes:
Electric turnstiles can be equipped with user notication lights (JS2) that indicate turnstile status. The user notication
lights are installed to the turnstile lid and can be congured to function in the following manners:
• Red – Indicates the turnstile is locked and ready for card presentation.
• Green – Indicates the access system has provided the turnstile control board with an activation indicating an
“authorized” card has been presented. When the green light illuminates, the turnstile is unlocked and ready for
passage.
• Red – Indicates the access system has provided the turnstile control board with an activation indicating an
“unauthorized” card has been presented. When the red light illuminates, the turnstile will remain locked.
• Green – Indicates the access system has provided the turnstile control board with an activation indicating an
“authorized” card has been presented. When the green light illuminates, the turnstile is unlocked and ready for
passage.
• Yellow – Indicates the turnstile is locked and ready for card presentation.
Loss-of-Power Operation (Electric Models Only)
Drop-Arm (Optional)
User Notication Lights (Optional)
The drop arm option includes the 10-7822 turnstile control board. Refer to Appendix C on
Page 29 for 10-7822 layout and terminal descriptions.
Drop arm option is available on fail-lock solenoid conguration only.
NOTES

EDC Installation and Maintenance Instructions
Page 12 For assistance: [email protected] [phone] PUD1535R5-5
The key override manually locks or unlocks the turnstile in the desired direction. The key overrides are located on the
underside of the front panel near the turnstile arms base [Figure 8].
1. To engage the key override, turn the key 90°.
When not in use, store the keys in a safe location.
NOTE
Key
Overrides
Key Overrides
Fig. 8
Post-Installation Functions Check
1. Ensure the junction box switch is set to ON.
2. Conrm the turnstile arms are locked in the controlled direction(s).
3. Provide an activation. Conrm the turnstile unlocks and rotates.
4. Provide an activation again, but allow the automatic turnstile relock period to be reached (default is 20 seconds).
Conrm that the turnstile re-locks.
5. Set the junction box switch to OFF.
6. Conrm the following:
• If the turnstile is congured for Fail-Lock operation, conrm that the turnstile remains locked in the controlled
direction(s) upon loss of power.
• If the turnstile is congured for Fail-Safe operation, conrm that the turnstile rotates freely upon loss of power.
• If the drop arm option is installed, verify the horizontal arm drops to the open position. Manually move the
drop arm back to the closed position.
7. Set the junction box switch to ON.
8. Close and lock the turnstile lid.
The automatic turnstile relock setting can be congured using DIP switch bank SW4 on the
turnstile control board [Figure 7].
NOTE
A lithium battery-powered LCD counter can be installed on electric and non-electric models. Each rotation of the
turnstile arm generates a count. One counter is required per direction. Counters can be ordered as reset or non-reset
versions.
1. To reset the counter, use the counter reset key and turn 90°. The counter reset lock is located next to the counter
display.
Local Battery Counter (Optional)
Key Override

EDC Installation and Maintenance Instructions
PUD1535R5-5 For assistance: [email protected] [phone] Page 13
IMPORTANT
Cleaning and Maintenance
In order to maximize the longevity of the turnstile, Alvarado recommends adhering to the following maintenance
schedule. The maintenance schedule is based on what we would consider a typical installation, which is in a temperate
climate with usage averaging 7500 activations per week. All maintenance items are described in more detail beginning
on Page 14.
ITEM # SERVICE DAILY 6 MONTHS YEARLY
EXTERIOR MAINTENANCE
1 Wipe down turnstile exterior with clean, damp cloth. X
2 Apply polish to all exterior surfaces. X
3 Apply sealant / wax to stainless steel / powder-coated
surfaces.
X
4 Chemically passivate stainless steel surfaces. Perform as needed
INTERIOR MAINTENANCE
5 Verify the threaded rods used to anchor the turnstile are
torqued to 80 ft-lbs.
X
6 Clean internal components with compressed air. X
7 Inspect all wires and contacts for exposure to metal parts
that may lead to a short.
X
8 Clean, test, and validate turnstile locking mechanism. X
9 Verify hydraulic closure unit is functioning properly. X
10 Lubricate turnstile pivot points, roller bearings, and
solenoid plungers with DuPont Teon Non-Stick Dry-Film
Lubricant.
X
11 Apply DeoxIT to all turnstile control board terminals and
wire harnesses.
X
Maintenance Schedule
If the turnstile is installed in a harsh outdoor environment such as a coastal area,
very hot or cold area, or area with high levels of dust and contaminants, or usage
exceeds 7500 activations per week, we recommend performing the 6 month and yearly
maintenance items every 3 months and 6 months, respectively.

EDC Installation and Maintenance Instructions
Page 14 For assistance: [email protected] [phone] PUD1535R5-5
Cleaning and Maintenance (cont.)
Exterior Maintenance
Refer to Page 13 for the Maintenance Schedule.
1) Wipe down turnstile with a clean, damp cloth.
Regular cleaning is the best way to maintain the turnstile's exterior nish. This is especially true for stainless steel
surfaces, where the goal should be to keep the protective chromium-oxide layer intact.
Regular cleaning can be accomplished by wiping all surfaces down with a clean and damp rag. For turnstiles that are
installed in harsh outdoor environments such as reneries or chemical plants, rinsing the stainless steel surface with
fresh water to wash away accumulated chemicals, materials, and particulates is recommended prior to wiping down.
Always try to clean equipment immediately after contact with chlorides (chlorine powder, salt melt, seawater, etc.).
2) Apply polish to all exterior surfaces.
Polish should be applied on a regular basis to preserve the aesthetic appeal and protect against rust, stubborn stains,
and heavy spotting. Our #1 recommendation for polish is Prism Liquid - Metal Polish. This product is safe for use on
stainless steel, aluminum, power-coated, and acrylic surfaces.
To apply, follow the manufacturer's instructions, but in brief: a) apply polish with a soft cloth, b) rub in a back-and-forth
motion in the direction of the grain, c) bu󰀨 with a clean towel until all residue is gone and the nish is bright and shiny.
If rust, stubborn stains, or heavy spotting are present, apply and rub polish using Scotch-Brite Hand Pads (7445) or
(7447) grits. Never use steel wool. Again, make sure to polish in the direction of the grain. Prism Liquid - Metal Polish
can be purchased at www.prismpolish.com.
Any deep scratches or chips in powder-coated nishes should be touched up to prevent a rust spot from forming. If left
untreated, rust will spread.
3) Apply sealant to stainless steel / powder-coated surfaces.
As a best practice, we recommend all stainless steel and powder-coated surfaces receive an application of sealant
for maximum protection throughout the year between polishes (especially when the turnstiles are subject to extreme
weather and excessive air- and water-born contaminants). Sealant will provide long-lasting protection from UV rays,
acid rain, air- and water-borne contaminants, and oils. The sealant we recommend is Prism Mirage Sealant and
Protectant. This particular sealant is wax-free, therefore it will not yellow, get sticky in the heat, or attract dirt. Sealant
should be applied directly after polishing.
To apply, follow the manufacturer's instructions, but in brief: a) apply sealant with a damp (not wet) sponge, one
section at a time, using a circular motion, b) allow to haze, c) bu󰀨 with a clean and dry cloth or electric bu󰀨er. Prism
Mirage Sealant and Protectant can be purchased at www.prismpolish.com.
4) Chemically passivate stainless steel surfaces.
If excessive rust and pitting has been allowed to develop, and polishing has not been e󰀨ective in removal, chemical
passivation is the next step. Chemical passivation is a process that is used to make the surface of stainless steel
“passive.” Passive means that the surface is resistant to corrosive reactions (such as rust).
To chemically passivate stainless steel, Alvarado recommends the use of a citric acid product called CitriSurf2310,
available from Stellar Solutions at www.citrisurf.com. This product is especially formulated to clean and passivate
stainless steel and can be used in the eld. Follow the manufacturer’s directions.
In especially harsh environments, it is possible that chemical passivation will be need to performed on a more frequent
basis.
NOTE

EDC Installation and Maintenance Instructions
PUD1535R5-5 For assistance: [email protected] [phone] Page 15
Cleaning and Maintenance (cont.)
Interior Maintenance
5) Verify threaded rods are torqued to 80 ft-lbs.
Using a torque wrench (ft-lbs.) and 15/16” socket, verify the threaded rods are torqued to 80 ft-lbs.
This procedure requires the junction box / transformer be removed in order to access the left-
hand threaded rod. Refer to Pages 6 -7 for removal instructions.
6) Clean internal components with compressed air.
Using compressed air, blow dust, dirt, and debris from the interior of the turnstile. Pay extra-special attention to
the turnstile control board, optical sensor, and solenoids. Keep the can upright as much as possible to avoid liquid
discharge from the nozzle.
7) Inspect all wires and contacts for exposure to metal parts that may lead to a short.
Inspect all junction box wiring, turnstile control board and solenoid power wires, and optical sensor wire harness.
MAKE SURE POWER IS TURNED OFF AT THE BREAKER BEFORE INSPECTION
8) Clean, test, and validate turnstile locking mechanism
a. Check solenoid and return springs for any extensive wear or deformation.
NOTE: Replace springs every 5 years.
b. Check solenoids for proper engagement in the locked and unlocked positions.
NOTE: Fail-Safe operation requires that the solenoid be engaged for at least 30 minutes prior to testing.
c. Verify optical encoder wheel passes through the center o󰀨 the optical sensors.
d. Perform 10 rotations in each direction and validate locking / unlocking functionality. The turnstile should
re-lock after the turnstile arms are rotated.
9) Verify the hydraulic closure unit is functioning properly.
Verify the hydraulic closure is properly adjusted by observing the rotation of the turnstile arms. If the turnstile is
electrically controlled, use the key override to enable free passage prior to performing steps A - C.
a. Spin the arm once in the testing direction. The turnstile arm should rotate once and stop in the home position.
b. If the turnstile over-rotates, increase the hydraulic tension by removing the cotter-type pin at the top of the
hydraulic closure. Tighten the adjusting screw (clockwise) with a slotted screwdriver. Put the pin back in and
re-test. Test in increments of 1/8 of a turn, not exceeding 1 full turn (360°). NOTE: DO NOT bottom out the
adjusting screw.
c. If the turnstile under-rotates (returns to standard position very slowly), decrease the hydraulic tension by
removing the cotter-type pin at the top of the hydraulic closure. Loosen the adjusting screw (counterclockwise)
with a slotted screwdriver. Put the pin back in and re-test. Test in increments of 1/8 of a turn, not exceeding 1
full turn (360°).
NOTE
CAUTION

EDC Installation and Maintenance Instructions
Page 16 For assistance: [email protected] [phone] PUD1535R5-5
Fig. 9
Lubrication Points
Interior Maintenance (cont.)
10) Lubricate turnstile pivot points, roller bearings, and solenoid plungers.
Alvarado strongly recommends DuPont Teon Non-Stick Dry-Film Lubricant (Liquid Form) be used when
lubricating the turnstile. This lubricant does not leave an oily lm and creates a dirt-resistant coating.
DuPont Teon Non-Stick Dry-Film Lubricant (Liquid Form) can be purchased online at www.amazon.com.
Pivot Points and Roller Bearings
a. Wipe down all component to be lubricated with a clean rag.
b. Apply Teon Non-Stick Dry-Film Lubricant to the locations indicated in [Figure 9].
Solenoid Plungers
a. Remove the solenoid spring shank from the plunger. Remove plunger and set aside.
b. Using a cotton swab dipped in isopropyl alcohol, clean the solenoid cavity and plunger, and allow to dry.
c. Coat the rst 1 - 1.5" of the plunger with a thin layer of Teon Non-Stick Dry-Film Lubricant. Allow to dry.
d. Insert plunger into the solenoid cavity and reinstall solenoid spring.
e. Repeat steps a - d on second solenoid and drop-arm solenoid (if installed).
1. Compression Arm Pivot
2. Reversing Pawl Pivot
3. Compression Shoe Pivot
4. Cam Shock Absorber Pivots
5. Hydraulic Closure Pivot
6. Roller Bearings
7. Lock Arm Pivots
8. Solenoid Plungers
9. Optional Drop Arm Pivot (not shown)
1
3
4
5
6
88
8
2
7
Optional
Drop Arm
Solenoid

EDC Installation and Maintenance Instructions
PUD1535R5-5 For assistance: [email protected] [phone] Page 17
Fig. 10
Turnstile Control Board (10-7821)
Interior Maintenance (cont.)
11) Apply DeoxIT to all turnstile control board terminals and wire harnesses.
DeoxIT is a contact cleaner / lubricant that is quite benecial for power and data connections. Yearly applications of
this product is strongly recommended in locations with harsh weather or high levels of air-borne contaminants.
We recommend DeoxIT D100L Needle Dispenser (P/N D100L-25C) for its balance of cleaning and lubrication
qualities, as well as ease of application. DeoxIT can be purchased at www.caig.com.
ENSURE PRIMARY POWER IS TURNED OFF PRIOR TO PERFORMING THIS PROCEDURE.
a. Disconnect all wires and wire harnesses from the turnstile control board [Figure 10].
b. Inspect wires and contacts for damage.
c. Apply DeoxIT to contacts. Allow to dry (2- 5 minutes).
d. Reconnect wires and wire harnesses to the turnstile control board.
e. Power on turnstile and check functionality.
CAUTION

EDC Installation and Maintenance Instructions
Page 18 For assistance: [email protected] [phone] PUD1535R5-5
Troubleshooting
ITEMS TO CHECK FIRST:
• Always check for and remove any debris in or around the solenoid plunger (do not, however, lubricate the solenoid
plunger. It is designed to operate “dry”.)
• Always check the wiring of the turnstile for any loose or bad connections.
• REMINDER NOTE: You can always test the functionality of the turnstile by pressing the activation test switch(s) on
the turnstile control board [Figure 7].
Symptom Possible Cause Solution
Turnstile
does not
unlock
There is no power to the
turnstile (Fail-Lock units
only).
Conrm that the ON/OFF switch is in the ON position.
Conrm that the fuse is still good. If necessary replace the
fuse.
Conrm that the LED on the turnstile control board is on and
not ickering. If the LED on the turnstile control board is not
lit, verify that proper voltage (110 -120VAC) is being provided
to the junction box inside the turnstile. Do this by plugging in
any device such as a light, drill, radio, etc.
If the proper voltage (110-120VAC) is being provided to the
junction box, verify that the turnstile control board is receiving
approximately 10 VAC from the transformer.
The turnstile is not
receiving an activation
signal from the access
control system.
Ensure that the access control system is properly connected
to the turnstile control board.
Conrm that the access control system is providing a proper
activation signal.
A lock arm spring is
missing, broken or worn
out.
Replace the springs.
NOTE: The springs installed in the EDC turnstile are
specically designed for use in this application. Use only
springs purchased from Alvarado. Turnstile springs are not
interchangeable and should only be used in their designated
locations. See Spring Kit in Appendix B on Page 27.
The lock arm is sticking
or binding in the locked
position.
Clean and lubricate the lock arms.
If necessary adjust the hydraulic closure as described
on Page 15.
The solenoid is defective. Test and replace the solenoid as necessary. See Solenoid
(12 VDC) Kit in Appendix B on Page 27.
The solenoid is
de-energizing but the
plunger is not “ring”.
Adjust the solenoid plunger-limiting bracket. See NOTE #2
on Page 20.
The turnstile control board
is defective.
Verify the green LED on the turnstile control board is
illuminated. Verify the test activation buttons on the turnstile
control board cause an activation when pressed. If either
of these tests fail, replace the turnstile control board. See
Turnstile Control Board Kit in Appendix B on Page 28.

EDC Installation and Maintenance Instructions
PUD1535R5-5 For assistance: [email protected] [phone] Page 19
Troubleshooting (cont.)
Symptom Possible Cause Solution
Turnstile
does not
re-lock
There is no power to the
turnstile (Fail-Safe units
only).
Conrm that the ON/OFF switch is in the ON position.
Conrm that the fuse is still good. If necessary replace the
fuse.
Conrm that the LED on the turnstile control board is on and
not ickering [Figure 7]. If the LED on the turnstile control
board is not lit, verify that proper voltage (110 -120VAC) is
being provided to the junction box inside the turnstile. Do this
by plugging in any device such as a light, drill, radio, etc.
If the proper voltage (110-120VAC) is being provided to the
junction box, verify that the turnstile control board is receiving
approximately 10 VAC from the transformer.
The optical sensors are
obstructed or misaligned.
Remove any dirt or debris that may be obstructing the optical
sensors.
If necessary, tighten the optical sensor mounting screws so
that the turnstile rotation tabs on the optical feedback disk
pass through the sensors clearly.
The optical sensor is
broken or not functioning
properly.
Repair or replace the optical sensor assembly. See Optical
Sensor Assembly Kit in Appendix B on page 26.
A lock arm spring is
missing, broken or worn
out.
Replace the springs. See Spring Kit in Appendix B on Page
27.
NOTE: The springs installed in the EDC turnstile are
specically designed for use in this application. Use only
springs purchased from Alvarado. Turnstile springs are not
interchangeable and should only be used in their designated
locations.
The solenoid is defective. Test and replace the solenoid as necessary.
The solenoid is
de-energizing but the
plunger is not “ring”.
Adjust the solenoid plunger-limiting bracket. See NOTE #2 on
Page 20.

EDC Installation and Maintenance Instructions
Page 20 For assistance: [email protected] [phone] PUD1535R5-5
Troubleshooting (cont.)
Symptom Possible Cause Solution
The turnstile
head does
not turn
smoothly.
The turnstile is not properly
lubricated.
Clean and lubricate the roller bearings as described in the
Lubrication section on Page 16.
If necessary adjust the hydraulic closure as described on
Page 15.
The solenoid
plunger is
sticking.
The solenoid is obstructed
by foreign matter or debris.
Remove any dirt or debris that may be obstructing the
solenoid or the plunger.
The solenoid bracket is out
of alignment.
Adjust the solenoid plunger-limiting bracket. See NOTE #2
below.
Symptom Possible Cause Solution
The
horizontal
drop arm
does not
drop during
loss of power
or re alarm
input.
The turnstile is not
receiving an activation
signal from the re alarm
/ emergency override
system.
Ensure that the re alarm / emergency override system is
properly connected to the turnstile control board.
Conrm that the re alarm / emergency override system is
providing a proper activation signal.
The drop arm solenoid
power wires are
disconnected.
Check drop arm solenoid wires and reconnect as necessary.
The drop arm solenoid is
defective.
Test and replace the solenoid as necessary.
The
horizontal
drop arm
does not lock
in the home
position.
Lock arm mechanism is
faulty.
Contact Alvarado Technical Support for assistance.