Alvarado SUPERVISOR 5000 User manual

Installation Instructions
Alvarado Manufacturing Company, Inc.
12660 Colony Street, Chino, CA 91710
Phone: [phone]
Fax: [phone]
[email protected]
www.alvaradomfg.com
SUPERVISOR 5000 with
Integrated IntraQ Admission Device
PUD4472R2-0

IntraQ-SU5000 Installation Instructions
Installation Instructions
Page 2 [email protected] [phone] www.alvaradomfg.com
Contents. ......................................................................................................................................................................... 2
ETL Certication. ............................................................................................................................................................. 2
Safety Precautions. ......................................................................................................................................................... 3
Safety Icons..................................................................................................................................................................... 3
Installation Tools. ............................................................................................................................................................. 4
Uncrating. ........................................................................................................................................................................ 4
Parts List.......................................................................................................................................................................... 4
Introduction...................................................................................................................................................................... 6
SU5000 Cabinets...................................................................................................................................................... 6
Before You Begin............................................................................................................................................................. 8
Slab Requirements. .................................................................................................................................................. 8
Space Requirements. ............................................................................................................................................... 8
Conduit Requirements. ............................................................................................................................................. 9
Electrical Requirements. ........................................................................................................................................... 9
Environmental Requirements.................................................................................................................................... 9
Communication Requirements................................................................................................................................ 10
User Training........................................................................................................................................................... 10
Pre-Installation Checklist. ....................................................................................................................................... 10
Pre-Installation Instructions. ...........................................................................................................................................11
Cabinet Panel Removal. ..........................................................................................................................................11
Baseplate Installation (Optional). ............................................................................................................................ 12
Pre-Installation Instructions. .......................................................................................................................................... 13
Anchoring the Turnstile. .......................................................................................................................................... 13
IntraQ Head Installation. ......................................................................................................................................... 15
Wiring Instructions......................................................................................................................................................... 16
Primary Power......................................................................................................................................................... 16
Crossover Cable Connection. ................................................................................................................................. 16
I/O Control Board. ................................................................................................................................................... 17
Conguring Free-Pass Exit............................................................................................................................................ 19
Ethernet Communication (Optional). ............................................................................................................................. 20
Barrier Installation.......................................................................................................................................................... 20
Post-Installation Functions Check. ................................................................................................................................ 22
Finish the Installation..................................................................................................................................................... 26
Cabinet Lid Installation............................................................................................................................................ 26
Cabinet Panel Installation. ...................................................................................................................................... 27
Base Cover Installation. .......................................................................................................................................... 27
Post-Installation Checklist. ............................................................................................................................................ 28
Troubleshooting............................................................................................................................................................. 29
Appendix A - Setting the Home Position........................................................................................................................ 30
Appendix B - 36" Single Lane - Plan, Elevation & Footprint Drawing............................................................................ 31
Appendix C - 28" & 36" Baseplate Dimensions............................................................................................................. 32
Appendix D - External DC Power Supply Installation (Optional). .................................................................................. 33
Appendix E - Multi-Lane Conduit Requirements. .......................................................................................................... 39
Appendix F - Crossover Cable Connection Diagrams................................................................................................... 40
Revision History............................................................................................................................................................. 41
Contents
This product is fully certied by a nationally recognized testing laboratory to UL 2593 and
CSA C22.2 #247. Unauthorized modication to this product in any way is prohibited.
ETL Certication

Installation Instructions
IntraQ-SU5000 Installation Instructions
Page 3[email protected] [phone] www.alvaradomfg.com
Safety Precautions
• For indoor use only.
• Use only skilled individuals to install and service the turnstile.
• DO NOT operate the turnstile if it has been damaged in any manner. If damaged, have the unit repaired or adjusted by a skilled service person
before use.
• DO NOT modify or alter the turnstile.
• Have skilled individuals maintain the turnstile according to a proper maintenance schedule.
• In access control applications, train all personnel that will be using the turnstile in the proper method of operation. In addition, properly train new
users as they are added to the system.
• DO NOT use non-Alvarado parts to repair a damaged turnstile.
• Closely follow the handling instructions for moving or lifting the turnstile during installation.
• Power o󰀨 the turnstile before connecting or disconnecting any communication or power wiring to the turnstile.
• Pour utilisation à l'intérieur seulement.
• Utilisez uniquement des personnes qualiées pour installer et entretenir le tourniquet.
• NE PAS faire fonctionner le tourniquet s'il a été endommagé de quelque façon. S'il est endommagé, faire réparer ou ajuster l'unité avant
l'utilisation par un(e) préposé(e) à l'entretien qualié(e).
• NE PAS modier ou altérer le tourniquet.
• Le tourniquet doit être maintenu selon un calendrier d'entretien adéquat par des personnes qualiées.
• Dans les applications de contrôle d'accès, former tout le personnel qui utilisera le tourniquet selon la bonne méthode de fonctionnement. De
plus, bien former les nouveaux utilisateurs à leur intégration au système.
• NE PAS utiliser des pièces ne provenant pas du Alvarado pour réparer un tourniquet endommagé.
• Suivez strictement les instructions de manutention pour déplacer ou soulever le tourniquet lors de l'installation
• Éteignez le tourniquet avant de brancher ou de débrancher le câblage de communication ou le câblage d'electricité.
• This turnstile can be used by children aged 12 years and above, and persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge, if they have been given supervision or instruction concerning use of the turnstile in a safe way and understand the
hazards involved. Children shall not play with or around the turnstile.
• The turnstile shall be disconnected from its power source during service and when replacing parts. The turnstile shall be disconnected from
its power source before connecting or disconnecting any communication or other activation/feedback control wires. If it is not possible that
the technician can check from any point to which he has access that the main power is removed, a disconnection with a locking system in the
isolated position shall be provided.
Safety Icons
The following symbols are used throughout the manual to highlight important information and potential risks when installing,
servicing or using the turnstiles covered in this manual.
WARNING This symbol is used in this manual to warn installers and operators of potential harm. Please read these
instructions very carefully.
CAUTION This symbol is used in this manual to designate potential conditions that may pose a risk to pedestrians,
personnel, property and equipment. Please read these instructions very carefully.
NOTE This symbol is used in this manual to designate useful information for the installer and operator. Please
read these instructions.
For questions, please contact Alvarado at [phone], Monday – Friday 7:00am to 4:00pm PST.
Please read this manual completely before installing or operating the purchased product.
WARNING The Supervisor 5000 may present a risk to persons and property if it is not installed and/or operated
correctly. This manual must be read in its entirety and all safety and operations information must be
followed. Note the following precautions:

IntraQ-SU5000 Installation Instructions
Installation Instructions
Page 4 [email protected] [phone] www.alvaradomfg.com
Installation Tools
• Tape Measure
• Chalk Line
• Pencil
• Hammer Drill
• 5/8" Concrete Drill Bit
• Shop Vac
• Hammer
• 3/32" hex key
• 1/8" hex key
• 9/16" Wrench
• Torque Wrench (ft-lbs.)
• Torque Wrench (in-lbs)
• 9/16" Socket
• Level
• 5/32" Allen Wrench
• #2 Phillips Head Screwdriver
• Precision Flat Head Screwdriver
• 4mm 'Stubby' Allen Wrench
(Supplied)
• Clear RTV Silicone
This product is shipped with all installation hardware and components. If installing a two-lane set, refer to the Two-Lane Set Parts List
below. For single-lane set, refer to the Single-Lane Set Parts List. Make sure that none of these parts are missing and/or damaged
before beginning installation. If parts are missing and/or damaged, please contact Alvarado.
Parts List
Uncrating
The SU5000 has been packed for shipping to prevent damage to the unit. Two or more installers are required
to unload the SU5000 at the installation site. Once the turnstile cabinets have been placed in the installation
location, carefully remove the protective packing material from the sides of the cabinets.
Main Cabinet
(Qty 1)
Secondary Cabinet
(Qty 1)
Main/Secondary Cabinet Lids
(Qty 2) IntraQ
(Qty 2)
Two-Lane Set Parts List
Center Cabinet
(Qty 1)
Center Cabinet Lid
(Qty 1)
Main Cabinet Base Cover
(Qty 1)
Secondary Cabinet Base Cover
(Qty 1)
Center Cabinet Base Cover
(Qty 1)

Installation Instructions
IntraQ-SU5000 Installation Instructions
Page 5[email protected] [phone] www.alvaradomfg.com
Parts List (cont.)
Main Cabinet
(Qty 1)
Secondary Cabinet
(Qty 1)
Main/Secondary Cabinet Lids
(Qty 2)
IntraQ
(Qty 1)
Single-Lane Set Parts List
Main Cabinet Base Cover
(Qty 1)
Secondary Cabinet Base Cover
(Qty 1)
Concrete Anchor Package:
Hardware:
Cabling:
Software:
• ⅜" x 2" Concrete Anchors (Qty 21)
• ⅜" x 2½" Hex Head Cap Screws (Qty 21)
• ⅜" Flat Washers (Qty 21)
• Barrier Clamp Bars (Qty 4)
• Barrier Clamp Bar Screws (Qty 16)
• 8' Crossover Cable (Qty 2)
• File Management USB (Qty 1)
Concrete Anchor Package:
Hardware:
Cabling:
Software:
• ⅜" x 2" Concrete Anchors (Qty 16)
• ⅜" x 2½" Hex Head Cap Screws (Qty 16)
• ⅜" Flat Washers (Qty 16)
• Barrier Clamp Bars (Qty 2)
• Barrier Clamp Bar Screws (Qty 8)
• 8' Crossover Cable (Qty 1)
• File Management USB (Qty 1)
Two-Lane Set Parts List (Cont.)
Barriers
(Qty 4)
(Barrier height and width may vary
from the barrier depicted above.)
Barriers
(Qty 2)
(Barrier height and width may vary
from the barrier depicted above.)

IntraQ-SU5000 Installation Instructions
Installation Instructions
Page 6 [email protected] [phone] www.alvaradomfg.com
Introduction
This manual covers the physical installation process for IntraQ-SU5000 Optical Turnstiles. A separate IntraQ-SU5000 User Guide
(PUD4454) provides operating instructions and additional information such as conguring turnstiles for bi-directional passage
applications and monitoring outputs. It is highly recommended that both this manual and the IntraQ-SU5000 User Guide (PUD4454)
be read in their entirety prior to beginning installation.
There are three types of SU5000 cabinets used to create passage lanes: a main cabinet, a secondary cabinet, and a center
(expansion) cabinet. A single passage lane consists of a main cabinet and a secondary cabinet [Fig. 1]. The center cabinet is used to
create additional passage lanes with the addition of a single cabinet [Fig. 2].
Each cabinet has an unsecured and secured side. The secured side is the side that requires access control to enter. The unsecured
side is typically the side from which patrons enter the facility.
Main Cabinet
The center portion of the main cabinet contains the main turnstile
controller, I/O control board, motor and motor control board, power supply,
safety sensor receivers, one moving barrier, and a power switch located at
the base on the secured side.
The top channel of the main cabinet contains the operational sensor
receivers, a drive system, and cabling for the IntraQ device.
Secondary Cabinet
The center portion of the secondary cabinet contains a motor and motor
control board, safety sensor transmitters, and one moving barrier.
The top channel of the secondary cabinet contains the operational sensor
transmitters, a drive system, and cabling for the IntraQ device.
SU5000 Cabinets
Center Cabinet (Multi-Lane Conguration)
Center cabinets contain both main and secondary
components. Center cabinets are extension cabinets used
in multi-lane applications. An unlimited number of center
cabinets can be added.
The center portion of the center cabinet contains the main
turnstile controller, I/O control board, two motors and two
motor control boards, power supply, safety sensors for
both the main and secondary side of the center cabinet,
two moving barriers, and a power switch located at the
base on the secured side of the main side.
The top channel of the center cabinet contains main and
secondary side operational sensors, two drive systems,
and two user status displays that communicate lane status
to the user. IntraQ devices can be installed on either end
of center cabinets.
Secured Side
Unsecured Side
Secondary
Cabinet
IntraQ IntraQ
Center
Cabinet
Main
Cabinet
Main
Side Secondary Side
Entry
Direction
Entry
Direction
Exit
Direction
Exit
Direction
IntraQ
Secured
Side
Unsecured Side
Secondary
Cabinet
Main
Cabinet
Entry
Direction
Exit
Direction
Single-Lane CongurationFig. 1
Multi-Lane CongurationMulti-Lane CongurationFig. 2

Installation Instructions
IntraQ-SU5000 Installation Instructions
Page 7[email protected] [phone] www.alvaradomfg.com
Passage Lane Width
36" Passage Lane
36.0 (914)
28" Passage Lane
28.0 (711)
SU5000 barriers come in widths to create 28" or 36" passage lanes [Fig. 4].
SU5000 barriers come in low (35"), mid (46") and full (69") heights [Fig. 3].
Barrier Height
IntraQ admission devices are mounted to the ends of SU5000 cabinets. They are typically installed on at least the unsecured side,
but they can be mounted on the secured side as well to process exit scans. IntraQ devices do not ship installed to the turnstile and
need to be mounted to the mounting plates after the SU5000 cabinets are installed.
IntraQ devices require an active network connection to a validation service to validate ticket scans and receive software updates.
IntraQ devices can connect to the network with an Ethernet or a wireless connection. The connection method used is determined by
which hardware is ordered.
SU5000 lanes can accept an optional Ethernet connection to allow software updates to be pushed to the devices.
Barrier HeightsBarrier HeightsFig. 3
Passage Lane WidthsPassage Lane WidthsFig. 4
Low Height
Barrier
6.0 (152)
35.0 (889)
Mid Height
Barrier
46.0 (1168)
6.0 (152)
Full Height
Barrier
69.0 (1752)
6.0 (152)
Network Communication
The IntraQ Admission Device

IntraQ-SU5000 Installation Instructions
Installation Instructions
Page 8 [email protected] [phone] www.alvaradomfg.com
Before You Begin
Use only skilled technicians for site preparation and installation of the turnstile using Alvarado’s instructions.
Refer to the footprint and plan drawings [Fig. 5] to determine the installation location and conduit requirements for a 28" single lane.
See "Appendix B - 36" Single Lane - Plan, Elevation & Footprint Drawing" on page 31 for 36" width.
The following slab requirements must be taken into consideration when selecting the installation location:
• A level solid concrete pad with a minimum thickness of 4" (102mm).
• Use full sweep electrical conduit underneath the oor.
• Three separate conduits for primary source power, external data, and the crossover cable must be used.
• Cabinets must be installed plumb with the oor while level and square to each other.
Footprint Drawing
Slab Requirements
Space Requirements
NOTE For ease of installation and service, allow 6" of space between cabinets and walls or other surfaces.
28" Single Lane - Plan, Elevation & Footprint Drawing28" Single Lane - Plan, Elevation & Footprint DrawingFig. 5
Elevation View
41.0
(1041)
5.9 (149)
34.8 (884)
45.9 (1165)
68.9 (1749)
Plan View
28.0 (711)
2.0 (51) 13.0 (330) 5.8 (146)
34.8 (885)
39.1 (993)
Minimum Req. Space
43.1 (1094)
60.8
(1544)
52.4
(1330)
4.3 (108)
C
L
C
L
0.9 (24)
0.9 (24)
0.7 (18)
1.9 (49)
1.3 (32)
1.3 (32)
23.4 (593)
6.3 (159)
3.3 (83) 2.6 (66) 3.3 (83)
6.3 (159)
23.4 (593)
0
7x 0.6 (14)
Anchoring Locations
Conduit
Hole
0

Installation Instructions
IntraQ-SU5000 Installation Instructions
Page 9[email protected] [phone] www.alvaradomfg.com
Conduit Requirements
SU5000 Conduit LinesSU5000 Conduit LinesFig. 6Fig. 6
Symbology Description Conduit Size
Primary
Power** 3/4”
Ethernet/Fire
Safety System 3/4”
Crossover
Cable
1”
**If the External DC Power Supply option was
ordered, use this conduit to route 24VDC.
The opening for the conduit in the center of each cabinet
is 6.50” x 2.50” (165mm x 64mm). The three required
conduits MUST t in this area [Fig. 6].
NOTE
For multi-lane conduit requirements, refer to "Appendix E -
Multi-Lane Conduit Requirements" on page 39.
NOTE Seal the oor area around the conduits running up and
into the cabinets. This will prevent condensation and
debris build-up coming from whatever may be below the
oor.
NOTE
• DO NOT install the product outdoors. This product is intended for indoor use only.
• DO NOT install the SU5000 where infrared lighting (strobe lights, ash photography, etc.) is in the direct path of the optical
sensors. Interference may a󰀨ect the performance of the turnstile.
The following are suggested operating temperature and humidity ranges for the SU5000:
Operation Non-Operation/Storage
Temperature Range 10-32°C / 50-90°F 0-40°C / 32-104°F
Humidity Range (Non-Condensing) 15% - 85% RH --
Environmental Requirements
Operating the SU5000 outside the listed temperature and humidity ranges may negatively a󰀨ect turnstile
performance, and could potentially cause damage to the turnstile and void the warranty.
CAUTION
Electrical Requirements
Power Supply 110-120 VAC, 60 Hz or 220/240 VAC, 50 Hz
Power Consumption (per Lane) Peak: 100W Operating: 65W Idle: 45W
Operational Voltage Primary power is stepped down and rectied for low-voltage 24 VDC, 12 VDC, and 5 VDC operation
Fuse 2.5A (slo-blo) located in the main cabinet
Drive Motor 24 VDC (brushless)
Surge Protection Alvarado suggests the use of surge protection on the high-voltage power line to further protect electronics

IntraQ-SU5000 Installation Instructions
Installation Instructions
Page 10 [email protected] [phone] www.alvaradomfg.com
Communication Requirements
The device must maintain an active network connection to the validation system to properly process scanned media. A networked PC
with Alvarado's GateUtility software is also recommended to allow for easy device conguration and le updates.
All personnel that will be involved with operating the IntraQ-SU5000 should be trained in the proper method of operation. Detailed
operation instructions are outside the scope of this manual, but can be found in the included IntraQ-SU5000 User Guide (PUD4454).
If further training is desired, contact Alvarado for information regarding on-site training services.
It is the installer's responsibility to ensure the following steps are completed before beginning the installation.
1. All components and hardware to be installed have been unpacked, correctly identied, and moved to the installation location.
2. The turnstile conguration and layout has been conrmed with the site manager.
3. All applicable requirements in the Before Getting Started section have been met.
User Training
Pre-Installation Checklist

Installation Instructions
IntraQ-SU5000 Installation Instructions
Page 11[email protected] [phone] www.alvaradomfg.com
Cabinet Panel Removal
Pre-Installation Instructions
1. Using a Phillips screwdriver, remove the six (6) mounting
screws that secure the cabinet panel to the main cabinet
[Fig. 7]. Do not discard the cabinet panel screws as they
will be reused.
2. Once the screws are removed, gently slide the cabinet
panel out of position and set the panel o󰀨 to the side.
3. Repeat steps 1 and 2 to remove the secondary cabinet
panel.
It is assumed that the Pre-Installation Checklist steps have been completed prior to beginning the installation.
NOTE
Cabinet Panel
Mounting Screws
Fig. 7Fig. 7 Removing ScrewsRemoving Screws

IntraQ-SU5000 Installation Instructions
Installation Instructions
Page 12 [email protected] [phone] www.alvaradomfg.com
Baseplate Installation (Optional)
The baseplate enables installation of the SU5000 turnstile on a solid foundation without the need to drill holes into the concrete. The baseplate also
provides concealed conduit channels for wiring primary power, crossover communication, and access control. Baseplates may be bridged together for
multi-lane congurations. The following information will guide the installer in baseplate installation:
1. Determine and mark the installation location.
2. Place the baseplate in the marked location.
3. Determine how the primary power and access control wiring will be routed to the main and/or center cabinet. Most commonly, the wiring is run
into the baseplate through one of the side plates and routed to the main and/or center cabinet. To remove the side plate, remove the four (4)
screws as shown in [Fig. 8].
4. Use the center cable channel to route the primary power, crossover cable, and access control wires as shown in [Fig. 8].
5. Mount the SU5000 cabinets to the baseplate at the anchor location using the supplied mounting bolts [Fig. 8].
6. For multi-lane applications, bridge the baseplates using the supplied bridge support(s) and screws [Fig. 8].
7. Reinstall the side plate(s).
Fig. 8 BaseplateBaseplate
Refer to "Appendix C - 28" & 36" Baseplate Dimensions" on page 32 for baseplate dimensions.
NOTE
Conduit holes for power and communication cables
(Use separate conduits for power and communication cables)
Anchor locations
Holes to link
multiple baseplates

Installation Instructions
IntraQ-SU5000 Installation Instructions
Page 13[email protected] [phone] www.alvaradomfg.com
1. Place the main cabinet and the secondary cabinet in the determined location [see "Space Requirements" on page 8].
2. All cabinets must be level and square to each other. This will ensure that the optical sensors are aligned, and that the barriers will line up properly
when installed. Use the following procedures to level the cabinets, and square each cabinet with respect to the oor and other cabinets:
3. Measure the distance from the inside wall of one cabinet top channel
to the inside wall of the other cabinet top channel, on both the entry
and exit side of the lane for a consistent measurement [Fig. 9].
4. Measure the diagonal distance from the end of one cabinet to the
end of the opposing cabinet, then measure the opposing diagonal
distance [Fig. 10]. If these distances are equal, the cabinets are
square.
5. Using a level, verify each cabinet is level [Fig. 11]. If necessary, shim
to bring the cabinets level.
Pre-Installation Instructions
Anchoring the Turnstile
The lane 1 main cabinet is always the right-most cabinet when viewed from the unsecured side.
NOTE
Fig. 11
Fig. 9 Fig. 10

IntraQ-SU5000 Installation Instructions
Installation Instructions
Page 14 [email protected] [phone] www.alvaradomfg.com
6. Remove cabinet end legs with a Phillips screwdriver and 3/32" hex
key [Fig. 12].
7. Remove the card reader mounting bracket and set aside.
8. Use a pencil and mark each mounting hole location
[Fig. 13]. There will be a total of seven (7) mounting holes per
cabinet. Remove the cabinets when complete.
9. Using a 5/8" concrete drill bit, drill the anchor holes 3" in depth at the
center of each marked location.
10. Insert the anchors into each drilled hole [Fig. 14]. The
threaded end of the anchor must be inserted into the hole
rst. Use a hammer to tap the anchors into place, if needed.
Ensure that the anchors are ush with the concrete oor.
11. If not already done, pull all wires (AC power, access control
and crossover cable) through conduit and conduit access in
center frame of cabinet prior to anchoring cabinets.
12. Using clear RTV silicone, seal the gaps between the conduit
and conduit holes.
13. Maneuver each cabinet over the anchor locations. Insert
seven (7) 3/8" x 2-1/2" anchor bolts and at washers.
14. Using a socket wrench and 9/16" socket, provisionally snug
the anchors. Do not fully tighten them yet.
15. Refer to "Barrier Installation" on page 20 and perform the
barrier leveling procedure.
16. Once cabinets are level and square to one another, torque
anchors to 80 ft-lbs.
Anchoring Holes
(7 total)
Concrete Anchor
Anchoring the Turnstile (cont.)
3/32" Allen
Wrench
Phillips
Screwdriver
UPPER END
LOWER END
End leg
screws
If drilling through terrazzo ooring, add the thickness of the terrazzo
tile to the hole depth. Use appropriate length anchor bolts.
CAUTION
The anchor holes must be clean before installing the anchor bolts.
If the holes are not clear of debris, the anchor bolts may not tighten
correctly.
NOTE
Removing End LegsRemoving End LegsFig. 12
Anchoring Holes
(7 total)
Marking Anchor HolesMarking Anchor Holes
Fig. 13
Inserting AnchorsInserting AnchorsFig. 14

Installation Instructions
IntraQ-SU5000 Installation Instructions
Page 15[email protected] [phone] www.alvaradomfg.com
IntraQ Head Installation
Fig. 15 Cable RoutingCable Routing
Fig. 16 IntraQ Case ScrewsIntraQ Case Screws
Fig. 17 IntraQ Case ScrewsIntraQ Case Screws
1. Route an Ethernet cable from the base of the cabinet to the Ethernet
connector in the top channel [Fig. 15].
2. Use a Phillips-head screwdriver to remove the four screws securing
the case to the IntraQ. Set the screws and the case to the side.
3. Line the mounting holes in the back of the IntraQ with the screw
holes on the SU5000 mounting plate. Feed the Ethernet, power,
and communication cables through the access hole in the IntraQ
backplate. Use a 1/8" hex key to tighten the screws and secure the
IntraQ to the SU5000 mounting plate.
4. Connect the Ethernet, power, and communication cables.
5. Use a Phillips-head screwdriver to secure the case to the IntraQ.
Cable Access
Hole
Access Hole
Ethernet
Connector
Exit Hole

IntraQ-SU5000 Installation Instructions
Installation Instructions
Page 16 [email protected] [phone] www.alvaradomfg.com
1. The included crossover cable interconnects communication signals
and low-voltage 24VDC between the main and secondary cabinets.
The default length of the crossover cable included with the SU5000 is
8'. Lanes wider than 36" must use a 13ft crossover cable.
Optional crossover cable lengths of 13', 20' and 40' are available.
2. Locate the low-voltage terminal block tucked in the bottom of the base
in the main cabinet [Fig. 20].
3. Insert the 24VDC positive wire (orange) and the negative wire (black)
into the terminal block, matching the colors with the other side and
tighten [Fig. 20].
4. Connect the data connector from the crossover cable to the data
connector in the main cabinet [Fig. 20].
5. Repeat Steps 1 – 3 for the secondary cabinet.
Wiring Instructions
The primary wiring lines for 110VAC and 220VAC consist of the
following:
Terminal 110V 220V
Neutral White Blue
Line Black Brown
Ground Green Green/Yellow
1. Locate the pre-installed power terminal block and
attached wiring (located next to the power key switch)
[Fig. 18].
2. Attach each power wire to the power terminal block with
the corresponding color exiting on the other side
[Fig. 18 & Fig. 19].
3. Using a Phillips head screwdriver, tighten each terminal
block connection.
Primary Power
Crossover Cable Connection
Data/Communication
Cable (tucked in the
bottom of the cabinet)
Crossover Cable
(packaged separately)
24VDC Power and
Ground Wire (tucked in
the bottom of the cabinet)
Fig. 20
L
N
G
220VAC
Fig. 19
Power Terminal
Block
Power Key
Switch
FOR EXTERNAL DC POWER SUPPLY INSTALLATION
INSTRUCTIONS, REFER TO "Appendix D - External DC
Power Supply Installation (Optional)" on page 33.
NOTE
110VAC and 220VAC primary power must be hard wired in
place. It is strongly recommended that a licensed electrician
perform this procedure in accordance with applicable local
codes.
NOTE
The crossover must connect from MAIN to SECONDARY.
Center cabinets have two crossover cable connectors tucked
in the base: one labeled MAIN and one labeled SECONDARY.
Crossover cables are used to interconnect main and secondary
connectors. Refer to "Appendix F - Crossover Cable Connection
Diagrams" on page 40 for crossover cable connection
diagrams.
NOTE
DO NOT MODIFY CROSSOVER CABLE.
CAUTION
L
N
G
110VAC
Power Terminal
Block
Power Key
Switch
Fig. 18

Installation Instructions
IntraQ-SU5000 Installation Instructions
Page 17[email protected] [phone] www.alvaradomfg.com
I/O Control Board
Fig. 21 Main CabinetMain Cabinet
Fig. 22 I/O Control Board I/O Control Board
LEGEND
ITEM NAME
J1 Input Terminals
J2 Output Terminals
JP3 Fire Alarm System Jumper
(N.O. - N.C.)
Signal Inputs and Outputs
To / From Access Control System
The I/O board is wired at the factory prior to shipment.
When uncrated, the cables from the I/O board are routed
up to the IntraQ mounting plate on master cabinets.
Inputs
Signal inputs from outside systems are wired into the
SU5000’s I/O control board. There are two types of input
signals, momentary dry contacts (MDC) and sustained dry
contacts (SDC). All input signals must be normally open
(N.O.), voltage-free, dry contacts, with the exception of
the re alarm input, which can be congured (via jumper
on the I/O control board) to accept either a normally
open or normally closed (N.C.) sustained contact. MDC’s
must be at least 100ms in duration to register. While the
SU5000 can accept signals up to 2 seconds in duration,
the suggested MDC input duration is 1 second or less to
support rapid throughput in high volume applications.
Outputs
Signal outputs are available from the SU5000’s I/O
control board. Outputs are normally open, voltage-free,
momentary dry contacts. The output signal length is
500ms in duration.
Inability to Provide Specied Inputs
If the access system cannot provide the specied MDCs,
isolation relays should be used.
102109
NOTE
NEVER connect signal lines
containing voltage directly to the
I/O control board.

IntraQ-SU5000 Installation Instructions
Installation Instructions
Page 18 [email protected] [phone] www.alvaradomfg.com
I/O Control Board (13-0328 Rev. G) Terminal Descriptions
J1 Input Contacts
Pin # Pin
Name
Function
Description
Contact
Type
Function & Behavior
Description
1GND Ground N/A Common input signal ground.
4ENTPAS Free
Passage
Entry
SDC Sets the turnstile to Free
Passage mode in the entry
direction.
8GND Ground N/A Common input signal ground.
11 EXTPAS Free
Passage
Exit
SDC Sets the turnstile to Free
Passage mode in the exit
direction.
15 GND Ground N/A Common input signal ground.
18 EMROVR Emergency
Override
SDC
(N.O. or
N.C.)
Opens the barriers toward
the unsecured side; barriers
remain open and turnstile is
inactive until SDC is removed,
or contact is reestablished
if N.C. jumper is enabled.
(Typically used for re alarm
or life safety systems.)
20 GND Ground N/A Common output signal ground.

Installation Instructions
IntraQ-SU5000 Installation Instructions
Page 19[email protected] [phone] www.alvaradomfg.com
The SU5000 can be congured to allow patrons to freely exit through the turnstile without having to scan a ticket or other scan media
rst. Follow the instructions below to congure the SU5000 to allow free-pass exits.
Conguring Free-Pass Exit
Entry Direction
1. Locate the ENTPAS and any GND terminal.
2. Using a wire jumper, connect the ENTPAS and GND
terminals
[Fig. 23].
Exit Direction
1. Locate the EXTPAS and any GND terminal.
2. Use a wire jumper to connect the EXTPAS and GND
terminals
[Fig. 23].
Fig. 23
Entry Direction
Exit Direction

IntraQ-SU5000 Installation Instructions
Installation Instructions
Page 20 [email protected] [phone] www.alvaradomfg.com
1. Locate the Ethernet extension cable tucked in the base of
the main/center cabinet [Fig. 24].
2. Connect the Ethernet cable to the Ethernet extension
cable.
3. Tuck the Ethernet extension cable back into the base of
the cabinet.
1. Insert the barrier edge into the mounting groove on the spindle,
aligning the barrier and spindle mounting holes [Fig. 25].
I/O Control BoardI/O Control BoardFig. 24
Barrier Installation
Ethernet Communication (Optional)
Ethernet Extension Ethernet Extension
CableCable
It is assumed that Ethernet cabling has been run to the
turnstile via conduit and pulled through the conduit opening in
Step 6 of the Anchoring the Turnstile section.
NOTE
NOTE
The barriers are shipped unattached
inside a crate. The clamp bars and
hardware are packaged in the box
labeled "HARDWARE ENCLOSED."
• Exercise care not to scratch the barriers
during handling. Do not lay or lean the
barriers on an abrasive surface. If the
barriers are going to be cleaned, use
only a soft cloth and a cleaner suitable
for acrylic surfaces.
• Barriers must be attached prior to
testing. Abnormal behavior may result if
tested without the barriers attached.
NOTE
This installation requires two people:
One person will need to hold the barrier
while the other person inserts and
tightens the mounting screws.
Inserting Barrier EdgeInserting Barrier EdgeFig. 25