Alvarado TAS12-EDM User manual

Alvarado Manufacturing Company, Inc.
12660 Colony Street, Chino, CA 91710
Telephone: [phone]
Fax: [phone]
[email protected]
www.alvaradomfg.com
PUD4005R1-0
Installation Instructions
TAS12-EDM TAS12P-EDM
TAS12-EDM & TAS12P-EDM
MOTORIZED INTELLIGENT ADMISSION TURNSTILE

TAS12-EDM & TAS12P-EDM Installation Instructions
Page 2 For Assistance: [email protected] [phone] PUD4005R1-0
Contents
Contents. ......................................................................................................................................................................... 2
Safety Icons..................................................................................................................................................................... 3
Safety Precautions. ......................................................................................................................................................... 3
Tools Required (Fixed Turnstile Installation).................................................................................................................... 4
Parts List.......................................................................................................................................................................... 5
Overview.......................................................................................................................................................................... 6
Power. ....................................................................................................................................................................... 6
Communication. ........................................................................................................................................................ 6
Installation Steps....................................................................................................................................................... 7
Before you Begin............................................................................................................................................................. 7
Site Preparation............................................................................................................................................................... 8
Slab Requirements. .................................................................................................................................................. 8
Space & Conduit Requirements................................................................................................................................ 8
Anchoring the Turnstile.................................................................................................................................................. 10
Primary Power Wiring Instructions. ................................................................................................................................11
TAS12 Installation ......................................................................................................................................................... 12
TAS12 Connection Instructions. .................................................................................................................................... 13
TAS12 Inputs........................................................................................................................................................... 13
Post-Installation Inspection............................................................................................................................................ 14
Post-Installation Functions Check. ................................................................................................................................ 14
Power On. ............................................................................................................................................................... 15
Perform TAS12 Device Tests. ................................................................................................................................. 16
Scan a Sample Barcode Ticket............................................................................................................................... 18
Validate RFID Media (Optional on TAS12P-EDM only). ......................................................................................... 18
Test Drop Arm Operation. ....................................................................................................................................... 19
Test Key Override Operation.(Optional).................................................................................................................. 20
Test the Local Counter (Optional). .......................................................................................................................... 21
Post-Installation Checklist. ............................................................................................................................................ 22
Troubleshooting............................................................................................................................................................. 23
Appendix A - Portable Base Turnstile. ........................................................................................................................... 24
Installing Neutrik Connector to AC Cord. ................................................................................................................ 25
Connecting AC Power to the Portable Turnstile (AC-Powered Option Only). ......................................................... 26
Charging the Portable Turnstile (Battery-Powered Option Only). ........................................................................... 27
Portable Base Turnstile Plan, Elevation and Footprint Drawings............................................................................ 21
Revision History............................................................................................................................................................. 25
Please read this entire manual before installing or operating the product.

TAS12-EDM & TAS12P-EDM Installation Instructions
PUD4005R1-0 For Assistance: [email protected] [phone] Page 3
WARNING
• Use only skilled individuals to install and service the turnstile.
• The turnstile is not a toy. Do not allow children to play on or near the turnstile.
• Follow a proper maintenance schedule using skilled individuals.
• Do not operate the turnstile if it has been damaged, or is functioning incorrectly, in any manner. Have the
turnstile repaired by a skilled service person before placing back in use.
• Do not modify or alter the turnstile.
• Use only Alvarado parts when repairing or maintaining the turnstile.
• Ensure that patrons are supervised when using the turnstiles.
• Test the turnstile(s) daily, or prior to each event, to ensure proper functionality.
SAVE THESE INSTRUCTIONS
Upon completion of the installation process, it is the installer's responsibility to provide the project or site
manager with these Installation Instructions and the Operation and Maintenance Instructions.
Safety Precautions
The following symbols are used throughout the manual to highlight important information and potential risks when
installing, servicing or using the turnstiles covered in this manual.
WARNING This symbol is used in this manual to warn installers and operators of potential harm. Please
read these instructions very carefully.
This symbol is used in this manual to designate potential conditions that may pose a risk to
pedestrians, personnel, property and equipment. Please read these instructions very carefully.
This symbol is used in this manual to designate useful information for the installer and operator.
Please read these instructions.
Safety Icons
For questions, please contact Alvarado at [phone], Mon. – Fri. 7:00am to 4:00pm PST.
Please read this manual completely before installing or operating the product.
CAUTION
NOTE

TAS12-EDM & TAS12P-EDM Installation Instructions
Page 4 For Assistance: [email protected] [phone] PUD4005R1-0
• Socket Wrench
• Hammer Drill
• 5/8" Concrete Drill Bit
• Shop Vac
• 5/32" Allen Wrench
• 5/16" Open Wrench (Wireless antenna only)
• #2 Phillips Head Screwdriver
• Precision Flat Head Screwdriver
• Torque Wrench (ft-lbs)
• 9/16" Socket
• Hammer
• Tape Measure
• Chalk
• 5/8" ID Washer Shims
• Clear RTV Silicone
Tools Required (Fixed Turnstile Installation)
Tools required for Portable Base Turnstile installations are located in Appendix A - Portable
Base Turnstile on page 24.
NOTE

TAS12-EDM & TAS12P-EDM Installation Instructions
PUD4005R1-0 For Assistance: [email protected] [phone] Page 5
This product is shipped with installation hardware. Make sure that no parts are missing or damaged before beginning
installation. If parts are missing or damaged, please stop the installation and contact Alvarado. Additional copies of this
installation manual can be found at www.alvaradomfg.com.
Parts List
NOTE
TAS12-EDM
Turnstile
(Qty 1)
TAS12P-EDM
TAS12
(Qty 1)
Wireless Antenna*
(Qty 1)
*Wireless Option Only
Also included:
Anchoring Hardware
• Concrete Anchor Kit (Qty 1)
Keys (per turnstile)
• Turnstile Lid Keys (Qty 2)
Cabling
• RS232 Programming Cable
(Qty 1)
Turnstile lid keys are taped to the
turnstile arm. Make sure to locate
these keys prior to discarding
product packaging
TAS12P-EDM
printer ships
pre-installed.

TAS12-EDM & TAS12P-EDM Installation Instructions
Page 6 For Assistance: [email protected] [phone] PUD4005R1-0
This manual covers the physical installation process for TAS12-EDM, TAS12P-EDM, & DTAS12-EDM Motorized
Intelligent Admission Turnstiles. At the end of this process, you will be able to power up the turnstile and perform a
basic functions check to validate certain aspects of operation. Operation instructions are outside the scope of this
manual, and can be found in the Operation and Maintenance Instructions manual.
The turnstile is powered in one of three ways:
• Primary power - Primary power is run to the turnstile location via conduit and connected to terminal block located
inside the turnstile cabinet. Applicable to xed installations only.
• AC outlet - The turnstile is connected to an AC outlet using an exterior mounted AC inlet and extension cord.
Applicable to portable installations only.
• Rechargeable battery - The battery is charged by connecting to an AC outlet using an exterior mounted AC inlet
and extension cord. Applicable to portable installations only.
Before you begin, understand how your turnstiles will be powered. This manual focuses on primary power
connection for the basis of instruction. Instructions on AC outlet and battery connections can be found in Appendix A
on page 24.
Alvarado's Motorized Intelligent Admission Turnstiles are networked devices that communicate with Alvarado's access
control software (GateLink or GateConnect) via wired or wireless TCP/IP. How a turnstile communicates with the
network (wired or wireless) is dependent on what options were specied during the ordering process, and the type of
network used at the host facility. The turnstile will ship pre-congured with the network settings provided to Alvarado
during the ordering process.
When powered up, the turnstile should automatically connect to the server (provided the server is online). Network
conguration and troubleshooting is outside the scope of this manual. If you require additional information or
instruction, seek direction from your network administrator or project manager.
Overview
Power
Communication

TAS12-EDM & TAS12P-EDM Installation Instructions
PUD4005R1-0 For Assistance: [email protected] [phone] Page 7
• For xed turnstile installations, proceed to the Installation Instructions beginning on page 8.
• For portable turnstile installations, proceed to Appendix A - Portable Base Turnstile on page 24.
Depending on whether you are installing xed or portable turnstiles, certain sections of this manual may not be
applicable to your installation.
Fixed Installation
1. Anchor the turnstile to the concrete slab.
2. Connect primary power.
3. Mount the TAS12 unit to the turnstile lid.
4. Attach the TAS12 wireless antenna (if applicable).
5. Connect cables that interconnect the turnstile and
TAS12 unit.
6. Connect the Ethernet cable for network
communication (if applicable).
7. Inspect installation.
8. Perform a post-installation functions check.
9. Hand o󰀨 instruction manuals to the project or site
manager.
Portable Installation
1. Install the guide rail to the portable base plate.
2. Mount the TAS12 unit to the turnstile lid.
3. Attach the TAS12 wireless antenna (if applicable).
4. Connect cables that interconnect the turnstile and
TAS12 unit.
5. Connect the Ethernet cable for network
communication (if applicable).
6. Inspect installation.
7. Wire Neutrik connector to AC power cord (AC power
cord not supplied by Alvarado).
8. Connect to an AC power source.
9. Perform a post-installation functions check.
10. Hand o󰀨 instruction manuals to the project or site
manager.
Installation Steps
Before you Begin

TAS12-EDM & TAS12P-EDM Installation Instructions
Page 8 For Assistance: [email protected] [phone] PUD4005R1-0
Use only skilled technicians for site preparation and installation of the turnstile using Alvarado’s instructions. Refer to
the footprint and plan drawings [Figures 1 & 2] to determine the installation location and conduit requirements. See
Appendix A on page 24 for footprint and plan drawings for the Portable Base Turnstile.
• Use a level, solid concrete pad with minimum size of 4' x 4' and a minimum thickness of 4" (101.5mm).
• Do not install the turnstile on asphalt.
• There must 2" (50.8mm) of clearance between the turnstile arm and the adjacent turnstile or barrier [Figure 1].
• Stub up conduit in accordance with local electrical codes.
• Always verify the layout of the turnstile(s) before installation.
Site Preparation
Fig. 2
Fig. 1
Slab Requirements
Space & Conduit Requirements
CONDUIT HOLE 2X 5 [127]
0
37 [940]
39.2 [997]
3.8 [95]
43 [1092]
2X 4.5 [114]
6 [152]
2X 1.1 [28]
0
2X 8.4 [213]
9.5 [241]
2X 2.3 [57]
2X 3.4 [864]
4X .5 [13] THRU
ANCHORING
LOCATIONS
Adjacent Barrier or Turnstile
2" [50.8]
OPENING
2X 34 [864] OPENING

TAS12-EDM & TAS12P-EDM Installation Instructions
PUD4005R1-0 For Assistance: [email protected] [phone] Page 9
Space & Conduit Requirements (cont.)
L
Fig. 3a
Fig. 3b
Fig. 3c

TAS12-EDM & TAS12P-EDM Installation Instructions
Page 10 For Assistance: [email protected] [phone] PUD4005R1-0
Anchoring the Turnstile
1. Using a turnstile lid key, open the turnstile leg access
panels [Figure 4].
2. Using a 9/16" socket wrench, remove the four (4)
bolts that secure the temporary wood plate to the
turnstile. Discard the wood plate.
3. Place the turnstile in the desired location. Check
that the turnstile is level and does not rock. If the
turnstile is not level, shimming will be required before
anchoring.
Primary power terminal block and power button are
always located on the secured or internal side of the
facility. Keep this in mind when placing the turnstiles
according to project layout.
4. Transfer four (4) anchor locations to the oor
[Figure 5].
5. Move the turnstile to the side.
6. Using a hammer drill tted with a 5/8” concrete bit,
drill each anchor hole to a depth of 3” (76.2mm).
7. Using a shop vac, vacuum debris from the anchor
holes before installing the anchors. If the holes are
not clear of debris, the anchors may not tighten
properly.
8. Insert anchors into the drilled holes with the threaded
ends down. If needed, use a hammer to tap the
anchors into place. Ensure that the anchors are ush
with the concrete oor [Figure 6].
9. Return the turnstile to the install location, ensuring
the anchors holes are aligned.
10. Route primary power wiring and network cable (if
using) through the appropriate conduit opening into
the turnstile. Primary power wiring will be connected
in later steps.
11. Insert anchor bolts.
12. Using a torque wrench (ft-lbs.) and 9/16” socket,
torque the threaded rods to 20 ft.-lbs.
13. For outdoors installations, apply a thick bead of clear
RTV silicone around the base of turnstile legs to seal.
Anchoring Holes
(2 total)
Concrete Anchor
(Head and arms not shown for ease of view)
Access
Panels
Anchor
Locations
NOTE
Fig. 4
Fig. 5
Fig. 6

TAS12-EDM & TAS12P-EDM Installation Instructions
PUD4005R1-0 For Assistance: [email protected] [phone] Page 11
1. Using a turnstile lid key, open the cabinet lid.
2. Locate the six-pole primary power terminal block
[Figure 7].
3. Using a precision at-head screwdriver, connect
primary power wires according to the Table 1.
Primary Power Wiring Instructions
• Use a licensed electrician for the following steps and adhere to all applicable local codes.
• MAKE SURE PRIMARY POWER IS TURNED OFF AT THE BREAKER.
WARNING
Terminal 110V 220V
Line Black Brown
Neutral White Blue
Ground Green Green/Yellow
Primary
Power
(110VAC version shown)
The following instructions are for xed turnstile installations only. If you are installing
a portable AC-powered or battery-powered unit, please refer to Appendix A - Portable
Base Turnstile instructions on page 24.
NOTE
Fig. 7
Table 1

TAS12-EDM & TAS12P-EDM Installation Instructions
Page 12 For Assistance: [email protected] [phone] PUD4005R1-0
TAS12 Installation
3. If the turnstile was ordered with the wireless
communication option, the antenna will be
taped to the side of the TAS12 unit. Remove the
antenna and attach it to the back of the TAS12
using an 5/16" open wrench [Figure 9].
4. In case not already done, remove all packaging
from the TAS12 unit.
5. Place the TAS12 onto the lid and slide the unit
forward [Figure 10]. The base plate will act as
a guide; the dove tail plates will slide under the
base plate until they are ush with the front edge
of the base plate.
6. From the underside of the lid, use a 5/32" Allen
wrench and tighten the four (4) Allen head
screws.
1. Locate the (4) Allen head screws on the
underside of the turnstile lid [Figure 8].
2. Using a 5/32" Allen wrench, loosen the (4) Allen
head screws.
Antenna
(Optional)
(4) Allen
Head Screws
Dove Tail
Plates
Base Plate
NOTE If you are installing a Dual TAS12 turnstile, the TAS12 units will be labeled ENTRY and EXIT.
It is the responsibility of the installers to ensure the entry and exit TAS12 units are installed in
accordance to your project layout.
Fig. 8
Fig. 9
Fig. 10

TAS12-EDM & TAS12P-EDM Installation Instructions
PUD4005R1-0 For Assistance: [email protected] [phone] Page 13
TAS12 Connection Instructions
TAS12 Inputs
1. Power Input - Used to supply power to the TAS12.
Plug the 6-pin power connector into the power input (A).
2. Interface Input - TAS12 RS485 communication.
Plug the 20-pin connector into the interface input (B).
3. Printer Input (TAS12P-EDM Only)
Plug the USB printer cable into a USB port (C or E).
4. Ethernet (Wired communication only) Used for communication with local area network.
Plug the Ethernet cable into the Ethernet port (D).
5. Mag Stripe/RFID Reader Input (Optional for TAS12P-EDM models only)
Plug the mag stripe or RFID reader's USB cable into a USB port (C or E).
NOTE Ensure turnstile power is OFF before connecting TAS12 cabling.
TAS12 cables are routed to the TAS12 mounting location. Depending on the turnstile options ordered, not all wiring
instructions may be applicable.
A
B
C
DE
A
B
C
DE
Fig. 11 Fig. 12

TAS12-EDM & TAS12P-EDM Installation Instructions
Page 14 For Assistance: [email protected] [phone] PUD4005R1-0
Post-Installation Inspection
Perform this post-installation inspection BEFORE powering on the turnstile for the rst time.
1. Anchoring (xed installations only): Verify the anchor bolts are tensioned to 20 ft-lbs. Tighten if necessary.
2. TAS12: Verify the TAS12 mounting screws are tightened. Tighten if necessary.
3. Dust, Dirt, & Debris: While the unit is powered down, open the lid to reveal the interior electronics. Blow any dirt,
dust, and small debris out of the turnstile with low-pressure compressed air such as Dust-O󰀨.
4. Wiring: Inspect all wires and contacts for exposure to any metal parts that may lead to a short.
Perform the following checks to verify the turnstile is performing properly. Function checks are included for optional
peripherals (i.e. RFID, mag stripe reader, printer) and may not be applicable to your installation. If any problems are
encountered, please refer to the Troubleshooting section on page 23.
The following is assumed:
• The GateLink10 server is online and congured for use.
• The network is up and running.
• Thermal printer is loaded with paper (TAS12P-EDM models only).
• Sample credentials (i.e. barcode tickets, magnetic stripe cards, etc.) are available and have been congured
as valid credentials in the GateLink10 application.
• The turnstile passed the Post-Installation Inspection.
WHEN THE TURNSTILE IS POWERED ON, THE ARMS ROTATE FOR THE DURATION OF THE BOOT
UP PROCESS. BEFORE POWERING ON, PLEASE MAKE SURE THE AREA IS CLEAR OF PERSONS OR
PROPERTY.
Post-Installation Functions Check
NOTE
CAUTION

TAS12-EDM & TAS12P-EDM Installation Instructions
PUD4005R1-0 For Assistance: [email protected] [phone] Page 15
Power On
1. Power on the turnstile by pushing the recessed
power button on the arm side of the turnstile cabinet
using the eraser end of a pencil (or similar shaped
object). The location of the power button will di󰀨er
depending on if the turnstile is a right-hand or left-
hand unit [Figure 13].
2. Depending on how the turnstile is congured for
network communication, the turnstile boot up routine
will take approximately 15 seconds to 1 minute.
During boot up:
• The attendant notication lights will ash red
while establishing communication with the
GateLink 10 server [Figure 14.
• The arms will undergo test rotations.
• At the end of the boot up routine, the arms
will rest in the home position, and the TAS12
screen will display a message instructing the
guest to scan a ticket.
If the red attendant notication light continues to ash
after boot up, communication has not been established
with the GateLink 10 server. Refer to the Troubleshooting
section on page 23 and notify your network administrator.
Attendant
Notication
Lights
ON/OFF Button
In Right-Hand
Turnstiles
In Left-Hand
Turnstiles
NOTE
Fig. 13
Fig. 14

TAS12-EDM & TAS12P-EDM Installation Instructions
Page 16 For Assistance: [email protected] [phone] PUD4005R1-0
Perform TAS12 Device Tests (cont.)
1. From the Operator Functions Menu, press the Device
Tests button [Figure 16].
Perform TAS12 Device Tests
The use of a stylus is recommended for all touch screen
operations.
If the default Login ID is invalid, obtain a valid Login ID
from the system administrator,
1. Make sure the turnstile is online and communicating
with the GateLink10 server.
2. Tap the TAS12 screen three times to bring up the
Operator Login Screen [Figure 15].
3. Using the on-screen number pad, enter the default
numeric Login ID 123, and press the ENTER key.
NOTE
NOTE
Fig. 15
Fig. 16

TAS12-EDM & TAS12P-EDM Installation Instructions
PUD4005R1-0 For Assistance: [email protected] [phone] Page 17
Perform TAS12 Device Tests (cont.)
1. Press the button for the device test to be performed:
• Print Ticket - Press this button to print a
test ticket from the integrated thermal printer
(TAS12P-EDM only).
• Activate Relay - Press this button to test the
turnstile unlocking / locking functionality. After the
turnstile unlocks, rotate the arms. The turnstile
arms will re-lock after the rotation. If the arms
are not rotated, the turnstile will re-lock after 20
seconds.
If the rotation occurs in the entry direction, a
count will appear in Forward Rotation Count.
If the rotation occurs in the exit direction, a count
will appear in Back Rotation Count.
• Set Green LED On - Press this button to test the
green attendant notication LED. Press the button
a second time to turn the LED o󰀨.
• Set Yellow LED On - Press this button to test
the yellow attendant notication LED. Press the
button a second time to turn the LED o󰀨.
• Set Red LED On - Press this button to test the
red attendant notication LED. Press the button a
second time to turn the LED o󰀨.
2. Press the Close button to exit the Device Tests
submenu and return to the Operator Functions Menu.
Fig. 17

TAS12-EDM & TAS12P-EDM Installation Instructions
Page 18 For Assistance: [email protected] [phone] PUD4005R1-0
Validate RFID Media (Optional on TAS12P-EDM only)
The RFID reader is located under the blackout pad.
1. To scan an RFID card or wristband, position the media in
the center of the blackout pad [Figure 18]. The read range
of RFID media varies from .5” – 2”, so the best practice
is to touch the RFID media in the center of the pad. The
reader will beep when the RFID media has been read.
After reading, the RFID data is sent to the GateLink10
server for validation.
• When validated, a chime will sound, the "PRINTING"
graphic will display on the TAS12 screen, and the
ticket(s) will print and deposit at the printer bezel
[Figure 19].
• When validation fails, an "INVALID SCAN" graphic
will display on the TAS12 screen and an alert will
sound.
2. Scan the printed ticket by placing the barcode on the
blackout pad facing up and towards the turnstile [Figure
18]. When validated, a chime will sound, a "PLEASE
ENTER" graphic will display on the TAS12 screen, and the
attendant notication lights will show GREEN, prompting
entry through the turnstile.
This function check is applicable to TAS12P-EDM models
equipped with an RFID reader only. Ensure paper is loaded in
the thermal printer before beginning.
NOTE
Printed
Ticket
Printer
Bezel
Scan a sample barcode to activate the turnstile. Each
sample barcode is good for one passage only.
1. To scan, place the barcode on the blackout pad
facing up towards the imager [Figure 18]. The imager
will beep when the ticket has been scanned. After
scanning, the barcode is sent to the GateLink10
server for validation.
• When validated, a chime will sound, "PLEASE
ENTER" will display on the TAS12 screen,
and the attendant notication lights will show
GREEN, prompting entry through the turnstile.
• When validation fails, an alert will sound,
"INVALID SCAN" will display on the TAS12
screen, and the attendant notication lights will
show solid RED.
Scan a Sample Barcode Ticket
Fig. 18
Fig. 19

TAS12-EDM & TAS12P-EDM Installation Instructions
PUD4005R1-0 For Assistance: [email protected] [phone] Page 19
Drop Arm
Test Drop Arm Operation
The turnstile is designed for the horizontal arm to drop
upon loss of power.
To test drop-arm functionality:
1. Power OFF the turnstile
2. Verify the horizontal arm drops allowing free egress
[Figure 20].
3. Power ON the turnstile and verify the arms reset
and lock in the home position.
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
N/A
DRAWN
CHECKED
ENGR
DATE
NAME
TITLE:
SIZE
B
DWG. NO.
REV
SCALE: 1:6
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
ANGULAR: 0.5
.XX [.X] = 0.06 [1.5mm]
.XXX [.XX] = 0.030 [0.76mm]
A
RGM
RPL
10/12/2016
10/12/2016
TAS12-MEDCS, LH
SHEET 1 OF 1
DO NOT SCALE DRAWING
6627
E.A.R. #
MATERIAL
MA120000
N/A
APPLICATION/ NEXT ASSY
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
ALVARADO MANUFACTURING INC. ANY
REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN
PERMISSION OF ALVARADO
MANUFACTURING INC. IS PROHIBITED.
N/A
FINISH
PART NO.
SEE TABLE
THIRD ANGLE PROJECTION
Alvarado Mfg. Co. Inc.
12660 Colony Street, Chino, CA 91710
909.591.8431 - 909.628.1403 (Fax) - www.alvaradomfg.com
When the turnstile is powered on, the arms rotate for
the duration of the boot up process. Before powering
on, please make sure the area is clear of persons or
property.
CAUTION
Fig. 20

TAS12-EDM & TAS12P-EDM Installation Instructions
Page 20 For Assistance: [email protected] [phone] PUD4005R1-0
Key Override switches are provided to manually place the turnstile in one of three passage modes: Free Passage,
Controlled Passage, and No Passage. There is one key override switch per rotation direction. The key switches are
located on the underside of the of the turnstile adjacent to the head and arms [Figure 21].
1. Turn key to the LEFT position for Free Passage mode: Verify the arms rotate freely in the appropriate direction. If
you have User Notication Lights installed, verify the GREEN light is illuminated.
2. Turn key to the CENTER position for Controlled Passage mode: Verify the arms are locked in the appropriate
direction and unlock with valid credentials. If you have User Notication Lights installed, verify the YELLOW light is
illuminated until activation occurs, in which it turns GREEN.
3. Turn key to the RIGHT position for No Passage mode: Verify the arms are locked in the appropriate direction and
remain locked even if valid credentials are presented. If you have User Notication Lights installed, verify the RED
light is illuminated.
Test Key Override Operation (Optional)
Key
Overrides
Free
Passage
Controlled
Passage
No
Passage
Fig. 21
Fig. 22