Alvarado EDM User manual

Alvarado Manufacturing Company, Inc.
12660 Colony Street, Chino, CA 91710
Telephone: [phone]
Fax: [phone]
[email protected]
www.alvaradomfg.com
PUD4146R1-0
Installation and Maintenance Instructions
EDM
Motorized Waist High Turnstile

Page 2 For Assistance: [email protected] [phone] PUD4146R1-0
EDM Installation and Maintenance Instructions
Contents
Contents. ......................................................................................................................................................................... 2
Safety Icons..................................................................................................................................................................... 3
Safety Precautions. ......................................................................................................................................................... 3
Tools Required................................................................................................................................................................. 4
Uncrating. ........................................................................................................................................................................ 4
Parts List.......................................................................................................................................................................... 4
Introduction...................................................................................................................................................................... 5
Before you Begin............................................................................................................................................................. 5
Slab Requirements. .................................................................................................................................................. 5
Space & Conduit Requirements................................................................................................................................ 6
Electrical Specications. ........................................................................................................................................... 8
Environmental Specications.................................................................................................................................... 8
Pre-Installation Checklist. ......................................................................................................................................... 8
Anchoring the Turnstile.................................................................................................................................................... 9
Primary Power Wiring Instructions. ............................................................................................................................... 10
Control Board Description........................................................................................................................................11
Using the Test Buttons....................................................................................................................................................11
Identifying Rotation Direction......................................................................................................................................... 12
Wiring the Control Board. .............................................................................................................................................. 13
Post-Installation Inspection............................................................................................................................................ 15
Powering On ................................................................................................................................................................. 15
Post-Installation Functions Check. ................................................................................................................................ 15
Loss of Power Operation. ....................................................................................................................................... 15
Testing Turnstile Functionality. ................................................................................................................................ 16
Test Key Override Operation................................................................................................................................... 18
Test the Local Counter (Optional). .......................................................................................................................... 19
Remote 3-Way Switch (Optional)............................................................................................................................ 20
User Status and Open / Close Lights (Optional)..................................................................................................... 20
EDM Utility. .................................................................................................................................................................... 21
Maintenance.................................................................................................................................................................. 23
Troubleshooting............................................................................................................................................................. 24
Appendix A - Setting the Home Position........................................................................................................................ 25
Appendix B - Portable Base Guide Rail Installation. ..................................................................................................... 26
Installing Neutrik Connector to AC Cord. ................................................................................................................ 27
Connecting AC Power to the Portable Turnstile (AC-Powered Option Only). ......................................................... 28
Portable Base - Plan, Elevation and Footprint Drawing - EDM-Square. ....................................................................... 29
Appendix - C - Plan, Elevation and Footprint Drawing - EDM Bullnose. ....................................................................... 30
Portable Base - Plan, Elevation and Footprint Drawing - EDM-Bullnose. ..................................................................... 31
Revision History............................................................................................................................................................. 32
Please read this entire manual before installing or operating the product.

PUD4146R1-0 For Assistance: [email protected] [phone] Page 3
EDM Installation and Maintenance Instructions
WARNING
• Use only skilled individuals to install and service the turnstile.
• The turnstile is not a toy. Do not allow children to play on or near the turnstile.
• Follow a proper maintenance schedule using skilled individuals.
• Do not operate the turnstile if it has been damaged, or is functioning incorrectly, in any manner. Have the
turnstile repaired by a skilled service person before placing back in use.
• Do not modify or alter the turnstile.
• Use only Alvarado parts when repairing or maintaining the turnstile.
• Ensure that patrons are supervised when using the turnstiles.
SAVE THESE INSTRUCTIONS
Upon completion of the installation process, it is the installer's responsibility to provide the project or site
manager with this Installation and Maintenance Instruction manual.
Safety Precautions
The following symbols are used throughout the manual to highlight important information and potential risks when
installing, servicing or using the turnstiles covered in this manual.
WARNING This symbol is used in this manual to warn installers and operators of potential harm. Please
read these instructions very carefully.
This symbol is used in this manual to designate potential conditions that may pose a risk to
pedestrians, personnel, property and equipment. Please read these instructions very carefully.
This symbol is used in this manual to designate useful information for the installer and operator.
Please read these instructions.
Safety Icons
For further assistance, please contact Alvarado's Technical Support Department at
+1(909) 591 - 8431 or visit www.alvaradomfg.com and select the "Support" tab.
Support hours are Monday - Friday 6am - 4pm Pacic Time (excluding USA holidays).
Be prepared to accurately describe the problem and provide the serial number of the turnstile;
this is printed on a tag attached to the inner "leg" of the turnstile.
CAUTION
NOTE

Page 4 For Assistance: [email protected] [phone] PUD4146R1-0
EDM Installation and Maintenance Instructions
This product is shipped with installation hardware. Make sure that no parts are missing or damaged before beginning
installation. If parts are missing or damaged, please stop the installation and contact Alvarado. Additional copies of
this installation manual can be found at www.alvaradomfg.com.
Parts List
Turnstile
(Qty 1)
• Socket Wrench
• 9/16" Socket
• Hammer Drill
• 5/8" Concrete Drill Bit
• Shop Vac
• #2 Phillips Head Screwdriver
• Precision Flat Head Screwdriver
• Torque Wrench (ft.-lbs.)
• Hammer
• Tape Measure
• Clear RTV Silicone
Tools Required
Tools required for Portable Base Turnstile installations are located in Appendix B - Portable
Base Turnstile on page 26.
NOTE
Keys (per turnstile)
• Turnstile Lid Keys (Qty 2)
• Override Keys (Qty 2)
NOTE
Keys are taped to the turnstile arm.
Make sure to locate these keys prior
to discarding product packaging.
RS232 progamming cable is located
within the cabinet.
Anchoring Hardware
• Concrete Anchor Kit (Qty 1)
• Shim Kit (Qty 1)
Cables
• RS232 Programming cable (Qty 1)
Uncrating
The EDM has been packed for shipping to prevent damage to the unit. Two or more installers are required to
unload the EDM at the installation site. Once the turnstile cabinet has been placed in the installation location,
carefully remove the protective packing material from the sides of the cabinet.
(EDM-Square cabinet shown)

PUD4146R1-0 For Assistance: [email protected] [phone] Page 5
EDM Installation and Maintenance Instructions
• For xed turnstile installations, proceed to the Installation Instructions beginning on page 9.
• For portable turnstile installations, proceed to Appendix B - Portable Base Turnstile on page 26.
Depending on whether you are installing xed or portable turnstiles, certain sections of this manual may not be
applicable to your installation.
This manual covers the physical installation process for the EDM Motorized Waist High Turnstile. At the end of this
process, you will be able to power up the turnstile and perform a functions check to validate operation.
Introduction
Before you Begin
• Use a level, solid concrete pad with minimum size of 4' x 4' and a minimum thickness of 4" (101.5mm).
• Ensure concrete pad extends a minimum 5" from all sides of the turnstile footprint.
• Do not install the turnstile on asphalt.
Slab Requirements

Page 6 For Assistance: [email protected] [phone] PUD4146R1-0
EDM Installation and Maintenance Instructions
• There must be 2" (50.8mm) of clearance between the turnstile arm and the adjacent turnstile or barrier [Fig. 1].
• Stub up conduit in accordance with local electrical codes [Fig. 2].
• Always verify the layout of the turnstile(s) before anchor installation.
Fig. 2
Fig. 1
Space & Conduit Requirements
Adjacent Barrier or Turnstile
2" [50.8]
2X 5 [127]
0
37 [940]
39.2 [997]
3.8 [95]
43 [1092]
2X 4.5 [114]
6 [152]
2X 1.1 [28]
0
2X 8.4 [213]
9.5 [241]
2X 2.3 [57]
2X 34 [864]
4X .5 [13] THRU
ANCHORING
LOCATIONS
inches [mm]
Conduit Opening
Conduit Opening

PUD4146R1-0 For Assistance: [email protected] [phone] Page 7
EDM Installation and Maintenance Instructions
Space & Conduit Requirements (Cont.)
Fig. 3b
L
Fig. 3a
Fig. 3c
NOTE EDM-Square cabinet shown. Refer to Appendix C on page 30 for the EDM-Bullnose cabinet.

Page 8 For Assistance: [email protected] [phone] PUD4146R1-0
EDM Installation and Maintenance Instructions
Electrical Specications
Environmental Specications
Pre-Installation Checklist
UL Rated Power Supply 110-120 VAC, 60 Hz or 220-240 VAC, 50 Hz (optional)
Power Requirements Maximum power consumption is 60W per lane with all options installed.
Operational Voltage Primary power is stepped down and rectified for low voltage 24VDC, 12VDC, and 5VDC
operation.
Fuse Protection Primary power is fuse protected (3A/250VAC, slo-blo)
24VDC, 12VDC and 5VDC is fuse protected. The 24VDC power supply is rated for lightning and
industrial surges/per IEC 61000-4-2-5, 6, 8, 11)
It is the installer's responsibility to ensure the following steps are completed before beginning the installation.
1) All components and hardware to be installed have been unpacked, correctly identied, and moved to the
installation location.
2) The turnstile conguration and layout has been conrmed with the site manager.
3) Slab, Space, and Conduit requirements have been met.
Operating Temperature 10° to 115° F -12 to 46° C
Storage Temperature 30° to 160° F -1 to 71° C
Relative Humidity 90% (non-condensing) --

PUD4146R1-0 For Assistance: [email protected] [phone] Page 9
EDM Installation and Maintenance Instructions
Anchoring the Turnstile
Anchoring Holes
(2 total)
Concrete Anchor
(Head and arms not shown for ease of view)
Access
Panels
Anchor
Locations
Fig. 4
Fig. 5
Fig. 6
Use included Shim Kit as
necessary to level turnstile and
prevent rocking.
NOTE
1. Using a turnstile leg key, open the turnstile leg
access panels [Fig. 4].
2. Using a 9/16" socket wrench, remove the four (4)
bolts that secure the temporary wood plate to the
turnstile. Discard the wood plate.
3. Place the turnstile in the desired location.
For xed installations, primary power terminal block
and power button are always located on the secured
or internal side of the facility. Keep this in mind
when placing primary power conduit and turnstiles
according to the project layout.
4. Transfer four (4) anchor locations to the oor [Fig. 5].
5. Move the turnstile to the side.
6. Using a hammer drill tted with a 5/8” concrete bit,
drill each anchor hole to a depth of 3” (76.2mm).
7. Using a shop vac, vacuum debris from the anchor
holes before installing the anchors. If the holes are
not clear of debris, the anchors may not tighten
properly.
8. Insert anchors into the drilled holes with the threaded
ends down. If needed, use a hammer to tap the
anchors into place. Ensure that the anchors are ush
with the concrete oor [Fig. 6].
9. Return the turnstile to the install location, ensuring
the anchors holes are aligned.
10. Insert anchor bolts.
11. Using a torque wrench (ft-lbs.) and 9/16” socket,
torque the bolts to 20 ft.-lbs.
12. Route primary power and access control wiring
through the appropriate conduit opening into
the turnstile [Fig.5]. Primary power wiring will be
connected in later steps.
13. For outdoor installations, apply a thick bead of clear
RTV silicone around the base of turnstile legs to seal.
NOTE
Conduit Openings

Page 10 For Assistance: [email protected] [phone] PUD4146R1-0
EDM Installation and Maintenance Instructions
1. Using a turnstile lid key, open the cabinet lid.
2. Locate the six-pole primary power terminal block
[Fig. 7].
3. Using a precision at-head screwdriver, connect
primary power wires to the appropriate terminals
according to Table 1 [Fig. 7].
Primary Power Wiring Instructions
• Use a licensed electrician for the following steps and adhere to all applicable local codes.
• MAKE SURE PRIMARY POWER IS TURNED OFF AT THE BREAKER.
WARNING
Power
Button
(110VAC version shown)
The following instructions are for xed turnstile installations only. If you are installing
a portable AC-powered or battery-powered unit, please refer to Appendix B - Portable
Base Turnstile instructions on page 26.
NOTE
Fig. 7
Terminal 110V 220V
Line Black Brown
Neutral White Blue
Ground Green Green/Yellow
Table 1
Connect primary power
according to Table 1 here.

PUD4146R1-0 For Assistance: [email protected] [phone] Page 11
EDM Installation and Maintenance Instructions
J4
J5
J16
Control Board Description
Signal Inputs and Outputs
To / From Access Control
System
Inputs - J4 Terminal Block
Signal inputs from access control
systems are wired into the EDM’s
I/O input terminal block. There
are two types of input signals,
momentary dry contacts (MDC)
and sustained dry contacts (SDC).
All input signals must be normally
open (N.O.), voltage-free, dry
contacts. MDC’s must be greater
than 100ms in duration to register.
The suggested MDC input duration
is 1 second or less to support
rapid throughput in high volume
applications.
Outputs - J5 Terminal Block
Signal outputs are available from
the EDM’s I/O output terminal
block. Outputs are normally open,
voltage-free, momentary dry
contacts. The output signal length
is 500ms in duration.
NOTE
NEVER connect signal lines
containing voltage directly to the I/O
terminal strips. This will damage the
circuit board.
Fig. 8
The test buttons on the control board, ENPASS and EXPAS, are
used to simulate a valid credential activation [Fig. 9].
• ENPASS is used to simulate an activation in the CW direction.
It is located in the bottom left corner.
• EXPASS is used to simulate an activation in the CCW direction.
It is located above the J4 terminal block.
Fig. 9A Fig. 9B
Using the Test Buttons

Page 12 For Assistance: [email protected] [phone] PUD4146R1-0
EDM Installation and Maintenance Instructions
J5 Output Contacts
Pin # Pin
Name
Function
Description
Contact
Type
Function & Behavior
Description
Pin # Pin
Name
Function
Description
Contact
Type
Function & Behavior
Description
1 ENTUCX Exit Passage
Count
MDC Counts the number of
passages in the exit direction.
1 EXTPAS Free
Passage
CCW
SDC Sets the turnstile to Free
Passage mode in the CCW
direction.
2 ENTACX Entry
Passage
Count
MDC Counts the number of
passages in the entry
direction.
2 EXTREJ Bad Card
CCW
MDC Illuminates the CCW direction
RED User Status Icon for 2
seconds.
3 GNDX Ground N/A Common input ground signal. 3 EXTACC Good Card
CCW
MDC Opens the turnstile for one
authorized passage until
passage occurs or timeout.
4 4 EMROVR Emergency
Override
SDC
(N.O. or
N.C.)
Drops the arms for free egress.
Arms remain down and turnstile
is inactive until SDC is removed,
or contact is reestablished
if N.C. setting is enabled.
(Typically used for fire alarm
or life safety systems.)
5 5 GND Ground SDC Common input ground signal.
6 6 BARDISABLE Barrier
Disable
Mode
7 7 ALRRST SDC Changes the EMROVR contact
from N.O to N.C.
8 8 ENTSER No Passage
Mode CCW
SDC Sets the turnstile to No
Passage mode in the CCW
direction.
9 9 ENTOVR N/A N/A Not available in the EDM.
10 GND Ground N/A Common input ground signal
10 11 ENTCLS No Passage
Mode CW
SDC Sets the turnstile to No
Passage mode in the CW
direction.
11 12 ENTPAS Free
Passage
Mode CW
SDC Sets the turnstile to Free
Passage mode in the CW
direction.
12 13 ENTREJ Bad Card
CW
MDC Illuminates the CW side
RED User Status Icon for 2
seconds.
13 14 ENTACC Good Card
CW
MDC Opens the turnstile for one
authorized passage until
passage occurs or timeout.
14 15 GND Ground N/A Common input ground signal.
Emergency
Override State
Arm drops to allow for
barrier free operation.
J4 Terminal Block Input Contacts
MDC
Control Board Description (Cont.)
J5 Terminal Block Output Contacts J4 Input Contacts
Pin # Pin
Name
Function
Description
Contact
Type
Function & Behavior
Description
Pin # Pin
Name
Function
Description
Contact
Type
Function & Behavior
Description
1 ENTUCX CCW
Passage
Count
MDC
for each rotation in the CCW
direction.
1 EXTPAS Free
Passage
Exit
SDC Sets the turnstile to Free
Passage mode in the exit
direction.
2 ENTACX CW
Passage
Count
MDC
for each rotation in the CW
direction.
2 EXTREJ Bad Card
Exit
MDC Illuminates the exit direction
RED User Status Icon for 2
seconds.
3 GNDX Ground N/A Common input ground signal. 3 EXTACC Good Card
Exit
MDC Opens the turnstile for one
authorized passage until
passage occurs or timeout.
Emergency
Override
SDC
(N.O. or
N.C.)
**Opens the barriers toward
the unsecured side; barriers
remain open and turnstile is
inactive until SDC is removed,
or contact is reestablished
if N.C. jumper is enabled.
or life safety systems.)
Ground SDC Common input ground signal.
Barrier
Disable
Mode
N/A **Disables the barrier.
** SDC Sets the EMROVR contact to
N.O or N.C.
No Passage
Mode Exit
SDC Sets the turnstile to No
Passage mode in the exit
direction.
N/A N/A Not available in the EDM.
Ground N/A Common input ground signal
No Passage
Mode Entry
SDC Sets the turnstile to No
Passage mode in the entry
direction.
Free
Passage
Mode Entry
SDC Sets the turnstile to Free
Passage mode in the entry
direction.
Bad Card
Entry
MDC Illuminates the entry side
RED User Status Icon for 2
seconds.
Good Card
Entry
MDC Opens the turnstile for one
authorized passage until
passage occurs or timeout.
Ground N/A Common input ground signal.
Outputs a dry-contact closure
Outputs a dry-contact closure
Identifying Rotation Direction
Clockwise (CW):
Turnstile arms rotate in a clockwise direction when viewed
looking down from behind the cabinet.
Counter-Clockwise (CCW):
Turnstile arms rotate in a counter-clockwise direction when
viewed looking down from behind the cabinet.
CW
Secured
Side
CCW
Unsecured
Side
Fig. 10
Orientation shown for a right-handed cabinet.
Adjacent Barrier or Turnstile

PUD4146R1-0 For Assistance: [email protected] [phone] Page 13
EDM Installation and Maintenance Instructions
Wiring the Control Board
The EDM provides bidirectional access control in conjunction with the facility access control system.
For bidirectional applications, the CW and CCW directions can be individually congured to di󰀨erent passage
modes to suit facility requirements. For example, a turnstile can be congured for Controlled Passage in the CW
direction, and Free Passage mode in the CCW direction.
Passage modes are set by two methods: wiring access control leads to the appropriate I/O input terminal or the
key override. Instructions for wiring to the I/O input terminal block are provided below. Instructions on using the
key override is provided on page 18.
NOTE Ensure power to the turnstile is OFF when wiring the I/O Terminal Blocks.
Setting Controlled Passage Mode (I/O Input - J4 Terminal Block)
EXTPAS 1
EXTREJ 2
EXTACC 3
EMROVR 4
GND 5
BDISABLE 6
ALRRST 7
ENTSER 8
ENTOVR 9
GND 10
ENTCLS 11
ENTPAS 12
ENTREJ 13
ENTACC 14
GND 15
J4
TO ACCESS
CONTROL
SYSTEM
CW Direction
CCW Direction
TO ACCESS
CONTROL
SYSTEM
Counterclockwise Direction (CCW)
1. Locate the EXTACC and GND terminals on
the I/O J4 terminal block.
2. Connect the leads used to indicate an
authorized passage in the CCW direction to
the EXTACC and GND terminals.
Clockwise Direction (CW)
1. Locate the ENTACC and GND terminals on
the I/O J4 terminal block.
2. Connect the leads used to indicate an
authorized passage in the CW direction to
the ENTACC and GND terminals.

Page 14 For Assistance: [email protected] [phone] PUD4146R1-0
EDM Installation and Maintenance Instructions
Setting Free Passage Mode (I/O Input - J4 Terminal Block)
Counterclockwise Direction (CCW)
1. Locate the EXTPAS and GND terminals on
the I/O J4 terminal block.
2. Using a wire jumper, connect the EXTPAS
and GND terminals.
Clockwise Direction (CW)
1. Locate the ENTPAS and GND terminals on
the I/O J4 terminal block.
2. Using a wire jumper, connect the ENTPAS
and GND terminals.
CW Direction
CCW Direction
Setting No Passage Mode (I/O Input - J4 Terminal Block)
EXTPAS 1
EXTREJ 2
EXTACC 3
EMROVR 4
GND 5
BDISABLE 6
ALRRST 7
ENTSER 8
ENTOVR 9
GND 10
ENTCLS 11
ENTPAS 12
ENTREJ 13
ENTACC 14
GND 15
J4
EXTPAS 1
EXTREJ 2
EXTACC 3
EMROVR 4
GND 5
BDISABLE 6
ALRRST 7
ENTSER 8
ENTOVR 9
GND 10
ENTCLS 11
ENTPAS 12
ENTREJ 13
ENTACC 14
GND 15
J4 Counterclockwise Direction (CCW)
1. Locate the ENTSER and GND terminals on
the I/O J4 terminal block.
2. Using a wire jumper, connect the ENTSER
and GND terminals.
Clockwise Direction (CW)
1. Locate the ENTCLS and GND terminals on
the I/O J4 terminal block.
2. Using a wire jumper, connect the ENTCLS
and GND terminals.
CCW Direction
CW Direction

PUD4146R1-0 For Assistance: [email protected] [phone] Page 15
EDM Installation and Maintenance Instructions
Post-Installation Inspection
NOTE Perform this post-installation inspection BEFORE powering on the turnstile for the rst time.
1. Anchoring (xed installations only): Verify the anchor bolts are tensioned to 20 ft-lbs. Tighten if necessary.
2. Dust, Dirt, & Debris: While the unit is powered down, open the lid to reveal the interior electronics. Blow any
dirt, dust, and small debris out of the turnstile with low-pressure compressed air such as Dust-O󰀨.
3. Wiring: Inspect all wires and contacts for exposure to any metal parts that may lead to a short.
Perform the following checks to verify the turnstile is performing properly. Function checks are included for optional
accessories (i.e. User Status lights, Open / Close lights, Local Counters, etc.) and may not be applicable to your
installation. See page 19-20 for details on optional accessories. If any problems are encountered, refer to the
Troubleshooting section on page 24.
Post-Installation Functions Check
Loss of Power Operation
Fig. 11
Perform the following steps to conrm turnstile power-loss
conguration:
1. Power OFF the turnstile.
2. Verify the horizontal drop arm falls [Fig. 11].
3. Power ON the turnstile and verify the dropped
arm rotates and locks back into the home position.
Drop Arm
Powering On
Press the Power Button located on the primary power terminal block [Fig. 7].
The arms will rotate for the duration of the boot up sequence. Before powering on, ensure area is
clear of people and property.
CAUTION

Page 16 For Assistance: [email protected] [phone] PUD4146R1-0
EDM Installation and Maintenance Instructions
Testing Turnstile Functionality
Perform the following turnstile functionality tests to validate basic turnstile operation.
The following is assumed (Controlled Passage mode tests only):
• The access control system is operational and all access control wiring to the turnstile is connected.
• Valid access control cards are on hand for activating the turnstile.
If valid access control cards are not available, use the test buttons located on the control board to simulate an
activation. See page 11 for button location.
See page 20 for location of optional User Status and Open / Close lights.
Test Procedure Turnstile Response
Breakaway • Without providing an activation, push arms
in the direction of passage.
• Arms will rotate small
amount in the direction of
passage and then lock.
• Buzzer will sound.
• Arms reset in two seconds.
Optional Accessories:
• User Status lights change
from yellow to ashing red.
• Open / Close lights change
from green to red.
• Lights reset after two seconds.
Access Time-out • Provide an activation.
• Do not enter the turnstile
• Wait for the turnstile to time out
(default is 20 seconds.)
Optional Accessories:
• User Status lights change
from yellow to green.
• Lights reset after time-out
period.
• Arms will move a small
amount in the direction of
passage.
• Arms reset to home position
after the time-out period
expires.
Valid Passage • Provide an activation.
• Rotate the arms in the direction of
passage.
• Arms will move a small
amount in the direction of
passage.
• Arms will complete rotation as
patron walks through.
• Arms will reset to home
position after passage.
Optional Accessories:
• User Status lights change
from yellow to green.
• Lights reset after passage.

PUD4146R1-0 For Assistance: [email protected] [phone] Page 17
EDM Installation and Maintenance Instructions
Testing Turnstile Functionality (Cont.)
Test Procedure Turnstile Response
Drop Arm • Place a jumper across Pins 4 & 5,
EMROVR and GND, respectively.
EMROVR/GND
• Arms drop allowing passage
in emergency situations.
• Performs boot up sequence
and returns to normal
operation once jumper is
removed.
Optional Accessories:
• User Status and
Open / Close lights turn o󰀨.
Impact • Provide an activation.
• Begin to rotate the arms in the
passage direction and block with
either your hand or leg.
• Buzzer sounds
• Arms reset two seconds
after obstruction has cleared.
Optional Accessories:
• User Status lights change
from yellow to ashing red.
• Open / Close lights change
from green to red.
• All lights reset 2 seconds
after obstruction is clear.
• Place a jumper across Pins 5 & 6,
GND and BDISABLE, respectively.
OR
• Arms drop allowing barrier
free operation.
• Returns to normal function
once jumper is removed.
GND/BDISABLE

Page 18 For Assistance: [email protected] [phone] PUD4146R1-0
EDM Installation and Maintenance Instructions
Key Override switches are provided to manually place the turnstile into Controlled Passage or Free Passage. There
is one key override switch for each rotation direction. The key switches are located on the underside of the turnstile
adjacent to the head and arms [Fig. 12].
1. Default position - CENTER sets turnstile to Controlled Passage mode: Verify the arms are locked in the
appropriate direction and unlock with valid credentials. If you have User Status lights installed, verify the
YELLOW light is illuminated until activation occurs in which it turns GREEN.
2. The RIGHT position sets the turnstile to Free Passage mode: Verify the arms rotate freely in the appropriate
direction. If you have User Status lights installed, verify the GREEN light is ashing.
Test Key Override Operation
Fig.12a
Free
Passage
Controlled
Passage
Fig. 12
Key
Overrides
CW CCW

PUD4146R1-0 For Assistance: [email protected] [phone] Page 19
EDM Installation and Maintenance Instructions
Test the Local Counter (Optional)
The battery-powered LCD counter is used to count turnstile rotations. Each rotation of the turnstile arm generates
a count. One counter is required per rotation direction.
1. Place the turnstile in Free Passage Mode using the Key Override.
2. Rotate the turnstile arms several times. Verify that the counter is registering each rotation.
3. To reset the counter, use the counter reset key and turn 90°. The counter reset lock is located next to the
counter display on the turnstile lid. [Figure 13]
Counter
Reset Lock
Counter
REVISIONS
REV. DESCRIPTION DATE BY
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
N/A
DRAWN
CHECKED
ENGR
DATE
NAME
TITLE:
SIZE
B
DWG. NO.
REV
SCALE: 1:4
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES [mm]
ANGULAR: 0.5
.XX [.X] = 0.06 [1.5mm]
.XXX [.XX] = 0.030 [0.76mm]
A
RGM
RPL
10/12/2016
10/12/2016
TAS12-MEDCS, LH
SHEET 1 OF 1
DO NOT SCALE DRAWING
6627
E.A.R. #
MATERIAL
NOTES:
BREAK ALL SHARP EDGES. 1.
DIMENSIONS APPLY AFTER FINISH. 2.
MA120000
N/A
APPLICATION/ NEXT ASSY
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
ALVARADO MANUFACTURING INC. ANY
REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN
PERMISSION OF ALVARADO
MANUFACTURING INC. IS PROHIBITED.
N/A
FINISH
PART NO.
SEE TABLE
THIRD ANGLE PROJECTION
Alvarado Mfg. Co. Inc.
12660 Colony Street, Chino, CA 91710
909.591.8431 - 909.628.1403 (Fax) - www.alvaradomfg.com
Fig. 13
Fig. 13a

Page 20 For Assistance: [email protected] [phone] PUD4146R1-0
EDM Installation and Maintenance Instructions
Remote 3-Way Switch (Optional)
A three-position key switch can be provided that allows the turnstile to be placed in one of the three available
passage modes: Controlled, Free, or No Passage. A key switch is required for each direction of operation. RKO-3
key switches are provided loose, for installation in a location remote from the turnstile. This option is separate from
the two-position key override that is installed in the turnstile cabinet.
User Status and Open / Close Lights (Optional)
The EDM can be equipped with User Status lights. The User Status lights are installed ush under the turnstile lid and
are congured to function in the following manner [Fig. 14]:
• Yellow - The turnstile is locked in Controlled Mode ready for a valid card presentation.
• Green - When the green light illuminates, the turnstile is unlocked and ready for passage. The access
control system has provided the turnstile control board with an "authorized" input. This light ashes when
in Free Passage Mode.
• Red - The access control system provided the turnstile control board an "unauthorized" input, in which case
the turnstile remains locked. This light is solid when in No Passage Mode. This light also ashes if the
moving arms impact an object during rotation or if the arm is forced to move without an activation, called
"breakaway".
The EDM can also be equipped with Open / Close lights. The lights are installed on the upper "leg" of the cabinet and
perform in the following manner [Fig. 14]:
• Green - Illuminates when the turnstile is open for use.
• Red - Illuminates when the turnstile is closed for use and activation inputs are ignored. It also illuminates
solid if the moving arms encounter an impact or a breakaway.
Open / Close
Lights
User Status Lights
Fig. 14