Amana DK9001D User manual

Description
This kit is used to control condensate from the unit. Conden-
sate water drains from the chassis into the sleeve during
normal heat pump operation and during times of high
humidity when the unit is in cooling operation. The drain kit
allows the condensate from the outdoor and indoor coils to
be routed to a suitable area. It can be installed for either
outdoor or indoor use. For outdoor use, the condensate can
be drained from either the right- or left-hand side of the wall
sleeve. Local codes will determine the proper condensate
disposal. For indoor use, the drain components must be
installed on the bottom of the wall sleeve and connected to
a drain system inside the building.
NOTE: This drain kit serves only as a link between the unit
and field-supplied condensate drain system. Installing the
kit without connecting it to a drainage system will result in
inadequate condensate removal, possible leakage and
corrosion.
ALGAECIDE: Most algaecide products will cause damage
to the unit basepan or coils and should not be used. Contact
your sales representative for the recommended algaecide
pan treatment for your unit.
Part No. A3494906 (1)
The installation and servicing of the equipment should be done by
qualified experienced technicians.
The drain components for outdoor use must be installed
before the wall sleeve condenser grille.
1. Remove the rear enclosure panel and the sleeve stiff-
ener. These items can be removed from the inside of
the building.
2. Insert the 1/2” drain fitting in the opening of the outdoor
drain fitting gasket and plate. Secure this assembly into
the holes located on the rear of the wall sleeve using
two of the outdoor mounting screws provided.
3. Place the remaining outdoor gasket on the outside
blank-off plate and secure the assembly to the left rear
of wall sleeve with the two mounting screws provided.
Unit chassis installed immediately
Install the condenser grille to wall sleeve with hardware
provided. See condenser grille installation instructions.
Unit chassis installed later
Replace the rear enclosure panel in the wall sleeve to
protect the inside of the building from weather damage.
1/2" Drain Fitting
Outdoor
Drain Fitting
Plate
Outdoor Drain
Fitting Gasket
Outdoor Drain Fitting
Left Blank-Off
Drain
Fitting
Indoor
Drain Fitting
Gasket
Indoor
Drain Fitting
Plate
Outdoor
Mtg. Screws
Qty: 4
Indoor
Mtg. Screws
Qty: 2
Outdoor
Drain Fitting
Plate
Outdoor
Drain Fitting
Gasket
Qty: 2
Outdoor
Blank-Off Plate
Drain Kit Components
Installation for Outdoor Use
PTAC
COMBINATION DRAIN KIT (DK9001D)
INSTALLATION INSTRUCTIONS
For outdoor or indoor sleeve drainage
September 2003
NOTE
USE ONLY WS900BWALL SLEEVES WITH DK9001D.
DO NOT INSTALL THIS DRAIN KIT ON WS900DWALL
SLEEVES!

2
Installation for Indoor Use
The components of the wall sleeve drain kit for indoor use are shown in figure below. These components must be
installed prior to the installation of the wall sleeve.
1. Locate an area on the wall sleeve that will be inside the
room when the sleeve is installed. If a subbase is
installed, locate the kit a minimum of 3 1/2” from the
front flange of the wall sleeve. This clearance will
provide adequate clearance for the subbase.
2. Cutout the template shown to the right. Using this
template, locate and drill the drain kit holes as close to
the outside wall as possible.
3. Using detail A (above) as a guide, assemble the drain
gasket, drain fitting plate, and indoor drain fitting to-
gether. Install the assembly into the drilled holes and
secure using the two indoor mounting screws pro-
vided. The screws must be inserted INSIDE the wall
sleeve and TOP driven down into the drain fitting plate.
Ensure drain tube is not restricted. Cover the two
screw heads with a good quality outdoor caulking (not
supplied) for additional corrosion protection.
NOTE: If the drain fitting is not immediately connected
to an indoor drainage system after the wall sleeve
installation, plug the hole with cork (not included) to
prevent indoor water damage in case it rains.
4. Install a 1/2” ID tube or hose (not included) on the drain
fitting and interconnect it to the drain system inside of
the building. Ensure that there are no kinks or traps in
tube or hose. Kinks or traps can cause improper
drainage.
5. Install the two drain blank-off plates and outdoor drain
gaskets on the outdoor portion of the wall sleeve.
These components can be installed after the sleeve is
secured in the wall opening just prior to the installation
of the condenser grille and chassis.
Template
.187" DIA.
MTG. HOLES
(2)
C of
MTG.
HOLES
MIN.
DIM.
L
INSIDE EDGE OF
FRONT SLEEVE FLANGE
.687" .687"
.500" DIA.
3.5" Min.
for PTSB
clearance
(not to
scale)
DRAIN
GASKET
DRAIN
FITTING
PLATE
MTG.
SCREWS (2)
WALL
SLEEVE
BOTTOM
Detail A
Due to policy of continual product
improvement, the right is reserved to
change specifications and design
without notice.