AmazonBasics GXA09 User manual

Adjustable Bed Base with No Massage
Base de Lit Réglable sans Dispositif de Massage
Base para Cama Ajustable sin Masajeador
B07Y2F9HMX, B07Y2D8SF7, B07Y2CNMZN

English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3
EN
IMPORTANT SAFETY
INSTRUCTIONS
Read these instructions carefully and retain them for future use.
If this product is passed to a third party, then these instructions
must be included.
WARNING To reduce the risk of burns, fire, electric shock, or injury
to persons:
• Read all instructions before using the furnishing.
DANGER To reduce the risk of electric shock; always unplug this
furnishing from the electrical outlet before cleaning or servicing.
WARNING Risk of injury! Keep children away from the foot support.
CAUTION Risk of injury and fire! Connect only to the furnishing
specified in this instruction manual.
• Unplug from outlet before putting on or taking off parts.
• Close supervision is necessary when this furnishing is used by, or
near children, invalids, or disabled persons.
• Use this furnishing only for its intended use as described in these
instructions. Do not use attachments not recommended by the
manufacturer.
• Never operate this furnishing if it has a damaged cord or plug, if it is
not working properly, if it has been dropped or damaged, or dropped
into water. Return the furnishing to a service center for examination
and repair.
• Keep the cord away from heated surfaces.
• Never drop or insert any object into any opening.
• Do not use outdoors.
• Do not operate where aerosol (spray) products are being used or
where oxygen is being administered.
• To disconnect, turn all controls to the off position, then remove plug
from outlet.
• To reduce the risk of electric shock, this furnishing has a polarized
plug (one blade is wider than the other). This plug will fit in a polarized
outlet only one way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified electrician to install
the proper outlet. Do not change the plug in any way.

4
EN
Battery Warnings
• Exhausted batteries should be immediately removed from the remote
control and properly disposed.
• If the battery leaks avoid contact with skin and eyes. Rinse affected
areas immediately with plenty of clean water, then consult a doctor.
SAVE THESE INSTRUCTIONS
Intended Use
• This furnishing is a motorized bed base with a wireless remote
intended to hold and adjust the position of a mattress.
• This furnishing is intended for household use only. It is not intended
for medical or therapeutic use.
• This furnishing is intended to be used in dry indoor areas only.
• No liability will be accepted for damages resulting from improper use
or non-compliance with these instructions.
Before First Use
• Check the furnishing for transport damages.
• Remove all the packing materials.
• Before connecting the furnishing to the power supply, check that the
power supply voltage and current rating corresponds with the power
supply details shown on the furnishing rating label.
DANGER Risk of suffocation! Keep any packaging materials
away from children – these materials are a potential source of danger,
e.g. suffocation.

5
EN
Product Description
C
D
B
A
ABase frame
BPower supply with plug
CMattress holder
DBed leg x4
ERemote control with LED light
G K
E
H L
I M
J N
F
FBattery compartment
GHead and foot up
HHead up
IHead down
JFlashlight button
KHead and foot down
LFoot up
MFoot down
NFlat

6
EN
Operation
Inserting batteries
1.5V-AAA
1.5V-AAA
F
• Remove the battery compartment (F) cover on the backside of the
remote control (E).
• Insert 2x 1.5 V AAA batteries (not included).
• Close the battery compartment (F) cover.
Assembly
NOTICE
Review the assembly instructions to confirm that the
appropriate critical components and accessories are being used with
the furnishing.
• Unfold the base frame (A).
A

7
EN
• Attach the bed legs (D) on the base frame (A).
• Flip the base frame (A) over.
• Install the mattress holder on the end of the base frame (C).
D
C

8
EN
Connect to power
• Connect the plug (B) to a suitable socket-outlet.
Functions
(G): The head and foot of the base frame (A) rises up at the
same time.
(H): The head of the base frame (A) rises up.
(I): The head of the base frame (A) lowers.
(J): Turn on/off the flashlight on the remote control (F).
(K): The head and foot of the base frame (A) lowers at the
same time.
(L): The foot of the base frame (A) rises up.
(M): The foot of the base frame (A) lowers.
(N): The base frame (A) resets to the original flat position.
max. 65°
max. 6.2" (15.8 cm)

9
EN
Pairing
• If the remote control (E) is not synced, press the recover button on
the main unit under the base frame (A).
• Hold the head down (I) and foot up (L) buttons for
10seconds. A beep is heard when the remote control (E) is synced.
Cleaning and Maintenance
WARNING Risk of electric shock! To prevent electric shock,
unplug the furnishing before cleaning.
WARNING Risk of electric shock! During cleaning do not
immerse the electrical parts of the furnishing in water or other liquids.
Never hold the furnishing under running water.
Cleaning the base frame (A)
• To clean the metal parts of the furnishing, wipe with a soft,
slightly moist cloth.
• Dry the furnishing after cleaning.
• Never use corrosive detergents, wire brushes, abrasive scourers,
metal or sharp utensils to clean the furnishing.
Cleaning the covers on the base frame
Machine wash 65-85 °F (30 °C)
Do not tumble dry. Do not bleach.
Do not iron. Do not dry clean.

10
EN
• Use a mild detergent or warm water to spot clean the covers.
• For deep cleaning, remove the covers to hand or machine wash.
• Let the covers dry before reattaching them to the base frame (A).
Maintenance
• Any other servicing than mentioned in this manual should be
performed by a professional repair center.
FCC Compliance Statement
1. This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.