Ametek mocon Dansensor MAP Mix ProVectus User manual

P/N 300862-K
11/2019
User Guide
&/

This blank page has been inserted to enable double sided
printing of the document!

Dansensor®MAP Mix Provectus EN User Guide
P/N 300862-K
11/2019
User Guide
Published by: MOCON Europe A/S
Rønnedevej 18
4100 Ringsted, Denmark
Tel [phone]
info[email protected]
www.dansensor.com
&/

2 User Guide EN Dansensor®MAP Mix Provectus
P/N 300862-K
11/2019

Dansensor®MAP Mix Provectus EN User Guide 3
P/N 300862-K
11/2019
Table of contents
1. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Intended Use of this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Reservations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Important! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Safety and Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Notes, cautions, warnings and tips! . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Tips and recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Operation and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2. Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Dansensor® MAP Mix Provectus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Flow System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
“Flow”. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
“Buffer”. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
3. Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Gas Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Correct mounting/dismounting of fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Correct tubing for gas inlets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
“Flow” versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
“Buffer” versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Power connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
I/O Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
COM-1/COM-2 Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Relay signalling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
I/O signals for machine control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Bridging of multiple mixers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

4 User Guide EN Dansensor®MAP Mix Provectus
P/N 300862-K
11/2019
4. Operation and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
The Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Start up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
“Black Box” models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Display models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Selecting a product for mixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Start mixer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Analog control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Errors/Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Error/Warning messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Error/Warning list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Using MAP Mix Provectus in MM8000 emulation mode . . . . . . . . . 35
MMP emulating MM8000 using PBI protocol (PSIP) interface on COM1 . . . . . . . 35
MMP as MM8000 using analogue control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
MMP emulating MM8000 connected to CMV-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Cables for use with MAP Mix Provectus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Cleaning and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Replacing gas inlet filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Replacing air inlet and outlet dust filters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
5. Menus and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Product menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Edit product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Clear product contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
View collected data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Delete collected data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Delete all collected data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Data log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Diagnostics menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
General setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Mixer configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Network setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Data log setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Formats/Units/Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Dansensor®MAP Mix Provectus EN User Guide 5
P/N 300862-K
11/2019
Access level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Change Supervisor PIN code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Export/Import . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
6. PuTTY Terminal Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Configuration and Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Initial configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Using PuTTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
7. Technical Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Electrical connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Connectivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Gas connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Basic specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Specification conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Pressure dependend flow capacity tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Spare parts, consumables and accessories. . . . . . . . . . . . . . . . . . . . . 75
Ordering items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Consumables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Toxic and Hazardous Substances or Elements. . . . . . . . . . . . . . . . . . 75

6 User Guide EN Dansensor®MAP Mix Provectus
P/N 300862-K
11/2019

Dansensor®MAP Mix Provectus EN User Guide 7
P/N 300862-K
11/2019
1. General Information
About this Manual
Intended Use of this Manual
This manual describes the common use and maintenance procedures of the
Dansensor® MAP Mix Provectus gas mixer.
It is intended for the daily users and should be kept with the equipment for reference at all
times.
Reservations
This manual was written and illustrated using the best possible information available at the
time of publication.
Any differences between this manual and the equipment reflect improvements introduced
after the publication of the manual.
Changes, technical inaccuracies and typographic errors will be corrected in subsequent
editions.
As a part of our policy of continuous improvement, we reserve the right to alter design and
specifications without further notice.
Important!
Safety and Use
Prior to using the equipment it is assumed that it has been properly installed and
configured as described in this manual.
The manufacturer cannot be held responsible for any damage caused by incorrect use of
this equipment.

8 User Guide EN Dansensor®MAP Mix Provectus
P/N 300862-K
11/2019
Notes, cautions, warnings and tips!
Throughout the manual notes, cautions, and warnings are indicated with various icons and
written in bold like the example below:
CAUTION! Never use hard tools or abrasive materials when cleaning any part of the
device.
Explanation
NOTE! The operator should observe and/or act according to the information in
order to obtain the best possible function of the equipment.
CAUTION! The operator must observe and/or act according to the information in
order to avoid any mechanical or electrical damage to the equipment.
WARNING! The operator must observe and/or act according to the information in
order to avoid any personnel injury.
Tips and recommendations
Tips, recommendations and “best practise” advises are indicated as shown in the example
below:
TIP! If grille does not come off easily, you can use a screwdriver or the like to release it. 

Dansensor®MAP Mix Provectus EN User Guide 9
P/N 300862-K
11/2019
Safety Instructions
Personnel operating and maintaining the device must be familiar with all aspects of its
operation and be proficient in maintenance.
Such personnel should review the following precautions to promote safety awareness.
General
Always refer to the manual before operating or maintaining the equipment.
Observe all WARNINGS, CAUTIONS and NOTES.
Do not open the device. In case of technical problems please contact your service provider.
Do not cover the machine with a cloth or piece of plastic to protect it from dust, as this
prevents free air circulation around the machine and might lead to overheating.
Do not expose the equipment to heavy moisture or heat and keep it away from direct
sunlight.
Never short circuit or remove safety devices.
Installation
To ensure the best installation with the least technical problems, please install equipment
as described in this manual.
Never install the equipment in explosive environments.
Always use correct fittings when connecting gas from the gas bottle.
Provide adequate space around the equipment for proper ventilation.
The units are Class 1 appliances and must be connected to an earthed mains connection.
It is the responsibility of the owner and operator(s) of the equipment, that the installation is
made in accordance with local rules and regulations.
When installing the equipment it is necessary to ensure proper ventilation in the room of
the installation in accordance with requirements from manufacturer.
The manufacturer cannot be held responsible for any damage caused by incorrect
installation of this equipment.
Operation and Maintenance
Be sure to disconnect electrical power and unplug the unit before performing any cleaning
or maintenance.
All panels and protective guards must be in place before operating the equipment.
When operating or maintaining the equipment always obey the relevant rules and
regulations for workers safety.
Repair or replace damaged power cords immediately.
Never block gas outlets.

10 User Guide EN Dansensor®MAP Mix Provectus
P/N 300862-K
11/2019

Dansensor®MAP Mix Provectus EN User Guide 11
P/N 300862-K
11/2019
2. Introduction
Dansensor® MAP Mix Provectus
Dansensor® MAP Mix Provectus is a proportional gas mixer for gas mixing and monitoring of
gas and pressure, especially designed for packaging machines, welding and other industrial
applications, where the gases Ar (option), O2, CO2, N2, and Air can be used in either 2-gas or 3-
gas combinations.
The mixing principle of Dansensor® MAP Mix Provectus is very stable and can be used for all
types of packaging machines, both flow packaging machines, vacuum packaging machines
and other industrial processes such as welding.
Dansensor® MAP Mix Provectus is user-friendly with very high precision, also under
conditions which usually cause problems for most other types of gas mixers.
In combination with the Dansensor® MAP Check 3 gas analyzer the mixer can replace the
older purging system 
TGC-2 and offer similar functionality by letting Dansensor® MAP Check 3 control the mixer.
Fig. 1. Dansensor® MAP Mix Provectus “Black-Box” and “Stand-Alone” versions
Dansensor® MAP Mix Provectus is offered either as a “Stand-Alone” version or a "Black-Box"
version without user interface. The “Black-Box”version is especially designed for cost effective
automated machine control and can only be externally controlled and maintained.

12 User Guide EN Dansensor®MAP Mix Provectus
P/N 300862-K
11/2019
Flow System
The figure below shows the internal flow system of the Dansensor® MAP Mix Provectus 2-
Gas and 3-Gas versions respectively.
The principle used in the gas mixer is based on the use of "Mass Flow Controllers" (MFC). For
each gas line in the mixer there is an MFC controlling the flow of the respective gas. The
mixture is programmed by the software and each MFC is then set to a flow proportional to the
required mixture of the respective gas.
Example: Total flow required = 500 l/min, 30% CO2and 70% N2; the software calculates the
necessary flow of each gas input (150l/min CO2and 350l/min N2) and the MFC´s are set to
deliver these flows.
Each MFC has a PID controller which controls the proportional valve based on the measured
flow from the Mass Flow Sensor and the set point.
The pressure drop through the gas mixer is much lower than on traditional mechanical mixers
and this assures maximum usage of the input gas pressure ranges and also allows running at
lower input pressures (depending on the back pressure at the output).
Each gas line is fitted with a pressure sensor (PS) and in case of low gas supply pressure a gas
input pressure alarm can be set to give an early "Alarm" signal to alert user of low gas supply
pressure.
If input pressure exceeds the minimal or maximal functional levels a "Fault" relay will be
activated. This can be used to stop the packaging machine.
PS
PS
PS
PS
PS
2
2
3
1
1
PS
PS
F3
F2
F2
F1
F1
MFC 1
MFC 1
MFC 2
MFC 2
MFC 3
PV
PV
PV
PV
PV
GAS
IN
GAS
IN
GAS
IN
GAS
IN
GAS
IN
MIX
OUT
MIX
OUT
FLOW/BUFFER
PRESSURE
FLOW/BUFFER
PRESSURE
Proportional
Valve 1
Proportional
Valve 2
Proportional
Valve 1
Proportional
Valve 2
Proportional
Valve 3
Pressure
Sensor 3
Pressure
Sensor 2
Pressure
Sensor 2
Pressure
Sensor 1
Pressure
Sensor 1
Pressure
Sensor 4
Pressure
Sensor 4
Mass Flow
Sensor 3
Mass Flow
Sensor 2
Mass Flow
Sensorr 2
Mass Flow
Sensor 1
Mass Flow
Sensor 1
3-GAS
2-GAS

Dansensor®MAP Mix Provectus EN User Guide 13
P/N 300862-K
11/2019
The mixer can be installed for either "Flow" or "Buffer" operation. The main difference is in the
installation (see explanation below).
“Flow”
The "Flow" mixer feeds gas directly to a line in the packaging machine. The built-in pressure
sensor has no control function but is solely used for monitoring of the output pressure.
“Buffer”
The "Buffer" version, which is typically used by vacuum packers, feeds gas to a buffer tank
from where the packaging machine gets its gas supply. The built-in pressure sensor is used to
maintain the set buffer tank pressure.
NOTE! We recommend that the buffer tank has a separate connection for the
pressure sensor. If this is not the case make sure to establish a connection on the
inlet string as close to the buffer tank as possible.
WARNING! Make sure that the gas outlet is NEVER blocked or restricted in front of
the buffer tank.
PS
MIX
OUT
FLOW
PRESSURE
TO PACKAGING
MACHINE
Pressure
Sensor 4
PS PS
MIX
OUT
MIX
OUT
TO PACKAGING
MACHINE
RECOMMENDED INSTALLATION ALTERNATIVE INSTALLATION
TO PACKAGING
MACHINE
BUFFER TANK
PRESSURE
BUFFER TANK
PRESSURE
Pressure
Sensor 4
Pressure
Sensor 4
BUFFER
TANK
BUFFER
TANK
MIX
OUT
TO PACKAGING
MACHINE
BUFFER
TANK

14 User Guide EN Dansensor®MAP Mix Provectus
P/N 300862-K
11/2019
Overview
5" touch panel color display (“Stand-Alone” versions only)
For intuitive operation of the device by use of explanatory icons and easy
understandable text messages and buttons.
USB host 
For connection of a memory stick (“Stand-Alone” versions only)
The connector is fitted with a water-proof cover.
All versions have a USB connector on the backside of the device as well.
ON/Status indicator (“Black-Box” versions only)
When lit power is on.
Colour/light combinations indicate the following:
• Green - steady Ready
• Green - flashing Mixing
• Red - steady Error (Fault)
• Red - flashing Warning


1SPEVDU
4UBSU
'MPX
MNJO

.FOV1SPEVDU
CBS CBS CBS CBS



0

$0

/

2
1
&2








Dansensor®MAP Mix Provectus EN User Guide 15
P/N 300862-K
11/2019
”POWER”
Power supply connector
Cooling air inlet grille
With dust filter and a fan inside the device
Cooling air outlet grille
With dust filter
“GAS IN (1-2-3)”
Connectors for inlet gasses (3-Gas mixer illustrated)
“MIX OUT”
Connector for mixed gas outlet
“PRESSURE SENSOR”
Inlet connector for flow gas/buffer pressure measurement
“I/O CONTROL”
Communication port (D-SUB 25) for packaging machine control signals
“COM1”
RS232 port (D-SUB 9) for connection to packaging machine, MAP Check 3 or master
mixer or external data collection and control via PC software (SDK-PSIP)
“COM2”
RS232 port (D-SUB 9) for control signals when controlling a slave mixer
."1.JY1SP7(BT






  

16 User Guide EN Dansensor®MAP Mix Provectus
P/N 300862-K
11/2019
LAN/Ethernet port 
Connection to local computer network for
- external data collection
- Modbus TCP communication with packaging machine
The port has 2 built-in status indicator LED’s
USB host 
For connection of a memory stick
“Stand-Alone”versions have a USB connector on the device front as well.

Dansensor®MAP Mix Provectus EN User Guide 17
P/N 300862-K
11/2019
3. Connections
Gas Connections
Correct mounting/dismounting of fittings
CAUTION! When mounting/dismounting fittings in order to change filters or
connect gasses, it is very important that you hold against on the already mounted
fittings to avoid damaging the existing assemblies.
Correct tubing for gas inlets
NOTE! To ensure a uniform gas flow into the device, there must be a straight hose
with a length of min. 30 cm (12”) between the gas inlet and the closest 90° elbow.
Alternatively the connection hose must have a bending radius of min. 5 cm (2”).

min. 30 cm 12( ")
R min. 5 cm (2")
R

18 User Guide EN Dansensor®MAP Mix Provectus
P/N 300862-K
11/2019
“Flow” versions
The input gas filters have been fitted to the “GAS IN” inlet connectors from the factory.
Connect the T-fitting to the “MIX OUT” outlet connector, then connect the hose fittings
using the gaskets to the T-fitting and to the gas filters on the “GAS IN” inlet
connectors.
Connect pressure measurement hose from the T-fitting to the “PRESSURE SENSOR”
inlet connector.
Connect the gas in- and outlet hoses and to the hose fittings on “GAS IN” and
“MIX OUT” using the hose clamps .
CAUTION! Never operate the mixer without installing the input filters .











."1.JY1SP7(BT