AMGOO am83Z User manual

mobilephone
Brand Name: AMGOO
Model Name: AM83Z
FCC ID: UOS-AM83Z

Please note
All the functions in this manual should
be operated in Standby Mode.
Like the picture below.
Tips:
Press END go back to the
Standby Mode
(Standby Mode)

Make a call
Input the numbers, Press Send1
or Send2 .
Answer a Call.
Press the Send1 or Send2
.
Tips:
*down Key to volume down..
*up Key to volume up.
*To unlock the keypad Left Soft
Key>*

OK> >OK
Missed Calls
OK> >OK>1
Display your recent missed numbers.
Dialed Calls
OK> >OK>2
Display your recent dialed numbers.
Received Calls
OK> >OK>3
Display your recent answered numbers.
Delete All
OK> >OK>4
You could delete all the records of the Dialed,
Received, Missed and Rejected.
Call timers
OK> >OK>5
Display Last Call, Received Calls, Dialed
Calls, and All Calls. Press Left Soft Key to
"Reset".
GPRS Counter

OK> >OK>6
Display Last sent, Last received, Total sent, and
Total received. Press Left Soft Key to "Reset".

Contacts
To browse the name card holder, store,
edit and delete the names and phone
numbers in the phone and SIM card.
Tips:
OK> >OK
To Add:
Options>New
To Edit
Choose the contact>Options>Edit
To Delete
Choose the contact>Options>Delete

Message
To receive and send the message.
OK> >OK
Write Message
To write new message.
In box
Store the SMS and Push message
Out box
Store the SMS you’ve sent in failure.
Drafts
Store the SMS you’ve edited.
Sent box
Store the SMS you’ve sent successfully.
Tip: Press # to select the desired input methods
Press * to input symbols

Multimedia
FM Radio
Please connect with the earphone You can
listen to Fm radio freely.
Press key
Tip: For the performance Multimedia
function please insert the T-flash card.
* key to volume down.
# key to volume up.

Bluetooth
Turn on or off Bluetooth.
Bluetooth settings: click to automatically search for and display the Bluetooth devices
list, touch the Menu button, the Bluetooth name rename detection timeout setting, display
the received file
Note:
A. display device name, search the device name is too long, it will automatically
truncated to the appropriate length.
B. select pairing the device will pop up a dialog box, the user needs to enter the
Bluetooth PIN match code. The two devices must use the same password. Headset or
earpiece kit may use a fixed password, you can refer to the Bluetooth headset instructions.
(Device can perform a lookup operation has been paired do not have to be matched.)

Camera
The device is equipped with a webcam
with high pixels. You can take photo at
any time.
Press OK> >OK>OK
Press ok to take the picture

Internet
The device is compatible with WAP
service. You can visit news, weather
forecast and airlines etc.
Press OK> >OK
*Depends on network support.

Calculator
Press OK> >4>OK

Settings
You can customize the settings, such as
time and date, language, call settings etc.
Tips:
Press OK> >OK

Ring settings:
OK> >OK.
To customize the ring
Settings options>settings>ring settings.
SIM 1 call ring
SIM1 message ring
SIM 2 call ring
SIM2 message ring

FCC RF EXPOSURE INFORMATION:
WARNING!! Read this information before using your phone
In August 1986 the Federal Communications Commission (FCC) of the United States with its
action in Report and Outer FCC 96-326 adopted an updated safety standard for human exposure
to radio frequency (RF) electromagnetic energy emitted by FCC regulated transmitters. Those
guidelines are consistent with the safety standard previously set by both U.S. and international
standards bodies. The design of this phone complies with the FCC guidelines and these
international standards. Use only the supplied or an approved antenna. Unauthorized antennas
modifications, or attachments could impair call quality, damage the phone, or result in violation
of FCC regulations. Do not use the phone with a damaged antenna. If a damaged antenna comes
into contact with the skin, a minor burn may result. Please contact your local dealer for
replacement antenna.
BODY-WORN OPERATION:
This device was tested for typical body-worn operations with the back of the phone kept 5mm
from the body. To comply with FCC RF exposure requirements, a minimum separation distance
of 5mm must be maintained between the user's body and the back of the phone, including the
antenna. Third-party belt-clips, holsters and similar accessories
containing metallic components shall not be used. Body-worn accessories
that cannot maintain 5mm separation distance between the user’s body and the back of the
phone, and have not been tested for typical body-worn operations may not comply with FCC RF
exposure limits and should be avoided.
For more information about RF exposure, please visit the FCC website at www.fcc.gov
Your wireless handheld portable telephone is a low power radio transmitter and receiver. When
it is ON, it receives and also sends out radio frequency (RF) signals. In August, 1996, the Federal
Communications Commissions (FCC) adopted RF exposure guidelines with safety levels for
hand-held wireless phones. Those guidelines are consistent with the safety standards previously
set by both U.S. and international standards bodies:
<ANSIC95.1> (1992) / <NCRP Report 86> (1986) / <ICIMIRP> (1996)
Those standards were based on comprehensive and periodic evaluations of the relevant
scientific literature. For example, over 120 scientists, engineers, and physicians from universities,
government health agencies, and industry reviewed the available body of research to develop
the ANSI Standard (C95.1). Nevertheless, we recommend that you use a hands-free kit with
your phone (such as an earpiece or headset) to avoid potential exposure to RF energy. The
design of your phone complies with the FCC guidelines (and those standards).
Use only the supplied or an approved replacement antenna. Unauthorized antennas,
modifications, or attachments could damage the phone and may violate FCC regulations.
NORMAL POSITION:
Hold the phone as you would any other telephone with the antenna pointed up and over your
shoulder.
RF Exposure Information:
This product is compliance to FCC RF Exposure requirements and refer to FCC website search for FCC
ID: UOS-AM83Z to gain further information include SAR Values.
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may
cause undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help
Do not use the device with the environment which below minimum -10℃or over maximum
50℃, the device may not work.
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

Thank you!