AMP Lighting ASM-2407 Operating and safety instructions

AMP®Low Voltage Landscape Lighting
AMP® Path & Area Light Stem
ASM-2407 & ASM-1203
INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com

Important Safety Instructions: Read Before Installation
INSTALLATION & MAINTENANCE GUIDE
This luminaire is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this
luminaire.
2. Warning: risk of electrical shock. Install all luminaires 10 feet (3.05M) or
more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that
are suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire, or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
7. If additional lengths of low voltage cable are required, please contact
www.amplighting.com or call 1-813-978-3900.
!
www.amplighting.com
–2–
SAVE THESE INSTRUCTIONS
AMP®Path & Area Light Stem
ASM-2407 & ASM-1203
Important Safety Instructions: Read Before Installation
!
LIGHTED LAMP IS HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
8. Do not operate the xture with a damaged or missing lens or shield.

[email protected] • 813.978.3900
Parts Required (sold separately)
–3–
Package Contents
A. (1) Stem
A. (1) Hat
B. (1) Bulb
C. Stake
Product Dimensions
Magnum Hat Pictured Here on
Standard stem
Magnum Hat Pictured Here on
Mini stem
9”
2 1/2”
22 1/2”

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
2
Remove Stem Top
1
AMP®Path & Area Light Stem
ASM-2407 & ASM-1203
Loosen the stem top and remove
it from the stem.
Install Bulb
Insert the bulb with the correct
wattage and type marked on the
xture label and push rmly into
place.
CAUTION: Do not exceed
maximum wattage marked on
luminaire label.
Socket
Bulb
3
Install Stem Top
Place the stem top over the
bulb and thread the stem top
onto the stem. Hand tighten
until snug.
Stem Top
Stem
Stem Top
Stem

[email protected] • 813.978.3900
–5–
Install Stake
4
Install Stem to Stake
5
Determine the desired location for
mounting the xture. Hammer the
stake into the ground until the ange
of the stake is ush to grade. To avoid
damage to the stake, place a board
on top of the stake while hammering.
NOTE: If the ground is hard and the
stake is difcult to install, make a
crosscut in the ground using a at
shovel.
Board
Stake
Soil
Ground
Clear away an area in the ground
at the wireway slot on the top
of the stake. Lay the luminaire
pigtail into the wireway slot and
attach the stem onto the stake.
Tighten until snug.
Stem
Stake
Pigtail
Wireway Slot