AMP Lighting AFL-4015-4-B-BZ Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Low Voltage Landscape Lighting
AMP® StoutPro PAR36 Flood Light (Lamp Ready)
AFL-4015-4-B-BZ

AMP®StoutPro PAR36 Flood Light (Lamp Ready)
AFL-4015-4-B-BZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
Important Safety Instructions
!
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS

[email protected] • 813.978.3900
Product Dimensions
–3–
1
Package Contents
A. (1) Fixture
Parts Required (sold separately)
A. (1) PAR36 Bulb
B. (1) Mounting Accessory
2.3”
4.65”
4.25”
Remove Glare Guard
Rotate the glare guard
counter clockwise and remove
it from the xture. Then
remove the bulb holder.
ROTATE
Fixture
Bulb Holder
Glare Guard

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
3
2
AMP®StoutPro PAR36 Flood Light (Lamp Ready)
AFL-4015-4-B-BZ
Install PAR36 Bulb
Fixture
Supply Wire
PAR36 Bulb
Screw
Use a PAR36 bulb (sold separately),
with the correct wattage and type
as marked on luminaire label.
Connect the supply wires using the
screws on the bottom of the PAR36
bulb, tighten with a screwdriver.
CAUTION: Do not exceed maximum
wattage marked on luminaire
label.
NOTE: DO NOT touch lamp with
bare hands. Use soft cloth to
handle lamp.
Install Bulb Holder and Glare Guard
Glare Guard
Tuck the excess wires inside
of the xture and place the
PAR36 bulb inside. Place the
bulb holder onto the top of
the PAR36 bulb and thread
the glare guard onto the
xture.
Fixture Bulb Holder
PAR36 Bulb

[email protected] • 813.978.3900
–5–
INSTALLATION & MAINTENANCE GUIDE
4
5
Install Stake
AMP®StoutPro PAR36 Flood Light (Lamp Ready)
AFL-4015-4-B-BZ
Board
Ground
Soil
Stake
Determine the desired location
for mounting the stake. Hammer
the stake into the ground until
ange of stake is ush to grade.
To avoid damage to the stake,
place a board on top of the stake
while hammering.
Note: If the ground is hard and
the stake is difcult to install,
make a crosscut in the ground
using a at shovel.
Install Fixture to Stake
Fixture
Wireway Slot
Ground
Soil
Stake
Cable
Clear away an area in the
ground at the wireway slot on
the top of the stake. Place the
xture wire into the wireway
slot and thread the xture onto
the stake. Hand tighten until
snug.

INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
6
Wire Connections
AMP®StoutPro PAR36 Flood Light (Lamp Ready)
AFL-4015-4-B-BZ
Strip both leads from the xture pigtail. Using two UL listed wire
connectors (sold separately), connect the leads from the xture to the
main supply cable leads.
Pigtail
Wire Connectors
Main Supply Cable
7
Adjust Fixture
Fixture
Screw
ROTATE
Loosen the knuckle and adjust the
xture to the desired orientation.
Tighten the knuckle after you nd
the desired orientation.

–6––6–
[email protected] • 813.978.3900
–7–
Install/Replace Bulb
Reverse Step 1 - Step 3 to expose the PAR36 bulb and replace it with correct
wattage and type marked on luminaire label. Reinstall glare guard.
IMPORTANT: Halogen lamps must be protected from moisture and dust
at all times. Always reinstall glare guard when removed.

IS-AFL-4015-4-B-BZ-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2020, AMP®Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com