AMX AutoPatch CP-10 User manual

Instruction Manual
AutoPatch Control Panel
CP-10
Control Panel
Release: 1/20/2009

Contents
i
CP-10 Instruction Manual
Contents
Introduction.........................................................................................................1
Applicability Notice ................................................................................................................. 1
Overview ................................................................................................................................. 1
Control Keys............................................................................................................................ 2
Executing Switches..............................................................................................3
Verifying Signal Status ........................................................................................5
Executing Presets ................................................................................................7
Global & Local Presets Overview............................................................................................. 7
Executing Local Presets........................................................................................................... 8
Defining Global Presets........................................................................................................... 9
Executing Global Presets....................................................................................................... 10
Checking the Software Version .........................................................................11
Installing a CP-10 Remote Control Panel...........................................................12
General Specifications ........................................................................................................... 12
Connecting to AMX AutoPatch Matrix Switcher ................................................................... 13
Applying Power ..................................................................................................................... 14
Rack Installation..................................................................................................................... 15
Executing a Test Switch.........................................................................................................15
Appendix A – System Error Codes ....................................................................17
Common System Error Codes................................................................................................ 17
Troubleshooting .................................................................................................................... 18
Technical Support.................................................................................................................. 18

Contents
ii CP-10 Instruction Manual

Introduction
1
CP-10 Instruction Manual
Introduction
Applicability Notice
The information in this manual applies to the CP-10 Control Panel, which comes with many of the
Modula pre-engineered systems or can be ordered as part of a custom system or as a remote control
panel.
Pre-Engineered Systems
The CP-10 is a component of a number of Modula pre-engineered systems that do not include
audio volume control. All Modula pre-engineered systems are numbered FGP34-xxxx-xxx
(e.g., FGP34-0412-112).
Custom Systems
The CP-10 can be ordered as an option for Modula 3 RU and 4 RU custom systems.
Remote Control Panel
The CP-10 Remote Control Panel (Model # FG1090-216) can be ordered as a separate unit to control
a Modula, a Modula CatPro, an Optima, an Optima SD, or a Precis SD.
Overview
The CP-10 is used for controlling the system’s switches and system attributes. Although control panels
are optional, we recommend one per system for system verification, redundant control, and
troubleshooting.
FIG. 1 illustrates a Modula Distribution Matrix with a CP-10 Control Panel. Other models may vary
slightly in appearance.
Note: AMX AutoPatch software can also be used to control a system; for more information, see the
“AMX AutoPatch CD.” In addition, AMX AutoPatch enclosures can be controlled using BCS (Basic
Control Structure) commands transmitted through an external controller; for more information, see
the “BCS Protocol Instruction Manual” on the CD or at www.amx.com.
CP-10 Control Panels for Custom Systems
Model # Type of Enclosure Models
FG1034-213 (3 RU) Modula 32x32 and flex-slot models
FG1034-234 (4 RU) Modula RGBHV/HD-15 and Modula CatPro models
FIG. 1 CP-10 on a Modula
Power
Indicator

Introduction
2CP-10 Instruction Manual
Control Keys
Note: The following keys are not currently implemented: Special, Undo, Comma, Period, and
Up and Down Arrows.
Keys & Functions
 Cancel Key – cancels an incomplete command and returns the panel to the Command screen.
Cannot undo a completed operation, i.e., an operation followed by the pressing of the
Take Key
 Take Key – functions like the “Enter” key on a computer key board. Pressing the Take Key
instructs the system to complete an operation
 Status Key – queries the system for signal routing information and switch verification
 Level Key – prepares the system to receive a level identification number. When controlling a
system with a CP-10, the terms “Level” and “VM (Virtual Matrix)” are interchangeable
 Change Key – prepares the system to accept a Change command
 Input (source) Key – prepares the system to receive an input (source) identification number
as the next entry
 Output (destination) Key – prepares the system to receive an output (destination)
identification number as the next entry
 Arrow Keys – scroll left or right through long lists of outputs (required only when an arrow
graphic is displayed on the LCD Command screen)
 Preset Key – implements local and global presets
 Program Key – displays software version only
 Backlight Key – illuminates the LCD for approximately 20 seconds. Press the Backlight Key
again to turn the backlight off before the 20 seconds are over
 Space Key – inserts a space between multiple outputs or multiple local presets when entering
a command. Output and local preset prompts are the only prompts that accept multiple
number entries
 Number Keys (0 - 9) – enter level, input, output, and preset numbers, and to enter digits for
any other functions that may require numbers
FIG. 2 CP-10 LCD & control panel keys
Arrow Keys
Number Keys (0 through 9)
LCD Command Screen
Command Keys
Take Key

Executing Switches
3
CP-10 Instruction Manual
Executing Switches
A switch is an active connection between an input (source) device and one or more output (destination)
devices. The signals routed in a switching operation are individual signals or groups of individual signals
coming through the connectors on the rear of an enclosure. You can execute switches from the CP-10
using the steps below.
Switching Level
All switches are executed on a specific level (virtual matrix). When controlling a system with a CP-10,
the terms “Level,” “virtual matrix,” and “VM” are interchangeable. The standard levels for most AMX
AutoPatch matrix switchers are: 0 = All (Audio-follow-Video), 1 = Video, and 2 = Audio.
Unless otherwise specified, switches are executed using the factory designated default level of
audio-follow-video (Level 0). When using the default, you do not have to press the Level Key and a
level number. When executing a switch on a level other than the default (e.g., video alone is usually
VM 1), you must press the Level Key and the desired level number. When specifying a level, be sure it
includes all the signals you want to route.
Executing Switches
In an execute switch command either an input or an output can be selected first. You can enter multiple
output signals, but only one input signal and only one level. To select multiple outputs, you must select
the input first. Once satisfied with the switch selections, press the Take Key to execute the switch.
You can return to the Command screen (FIG. 3) at any time by pressing the Cancel Key. Pressing the
Cancel Key does not cancel any completed operations.
For new installations, we recommend that before attaching all inputs and outputs, you execute a test
switch routing Input 1 to Output 2 on the level designated by the enclosure’s “Connector Guide.”
Depending on the signal type (e.g., component signals), you may need to attach multiple input and
output connectors.
FIG. 3 CP-10 Command screen

Executing Switches
4CP-10 Instruction Manual
The example following switches Input 1 to Output 2 on Level 0.
To execute a switch:
1. At the Command screen, press the Change Key.
The Change screen appears.
2. At the Change screen, press the Level Key and enter “0.”
3. Press the Input Key and enter “1.”
4. Press the Output Key and enter “2.”
5. Press the Take Key.
Input 1 is routed to Output 2, and the system returns to the Command screen.
To execute a switch with multiple outputs:
1. Complete Steps 1 through 3 above.
2. Press an Output Key and then press the Space Key, repeating until all desired outputs are selected
(use no more than 33 outputs at one time).
If necessary, use the left and right arrow keys to navigate through the entries.
3. Press the Take Key.
Input 1 is routed to Outputs 2, 3, 4, and 5, and the system returns to the Command screen.

Verifying Signal Status
5
CP-10 Instruction Manual
Verifying Signal Status
Signal status can be verified to confirm that a switch has executed properly or to confirm correct routing
to multiple outputs (destinations) without accidently executing or disconnecting switches. Input status
and output status both function on the CP-10 Control Panel. An output can only receive a signal from
one input (source); therefore verifying the status of an output will display only the one input it is
currently receiving a signal from. It will not show other outputs that are also receiving a signal from the
same input. Verifying an input will display all outputs currently receiving the input’s signal.
Once in Status mode, the CP-10 stays in Status mode until the Cancel Key is pressed. You can return to
the Command screen at any time by pressing the Cancel Key.
The following example verifies the signal status for Input 2 on Level 0.
To verify the status of an input signal:
1. At the Command screen, press the Status Key.
The Status screen appears.
2. Press the Level Key and enter “0.”
3. Press the Input Key and enter “2.”
4. Press the Take Key.
A single output –The Status screen below left indicates that Input 2 is routed to Output 4.
Multiple outputs –The Status screen below right indicates that Input 2 is routed to multiple
outputs. When the screen does not have enough room to display all of the outputs that the input is
routed to, use the right arrow key to scroll right and see the rest of the outputs.

Verifying Signal Status
6CP-10 Instruction Manual
No outputs – If no outputs are routed to the specific input, “DIS” (disconnect) displays in the
Output field. The Status screen below indicates that Input 2 is not routed to any outputs.
5. Press the Status Key to return to the Status screen and select another signal to verify.
Or
Press the Cancel Key to return to the Command screen.
The following example verifies the signal status of Output 9 on Level 0.
To verify the status of an output signal:
1. At the Command screen, press the Status Key.
The Status screen appears.
2. Press the Level Key and enter “0.”
3. Press the Output Key and enter “9.”
4. Press the Take Key.
An input –The status screen below left indicates that Output 9 is receiving a signal from Input 3.
No inputs –The Status screen below right displays “DIS” (disconnect) in the Input field, indicating
that Output 9 is not receiving a signal from an input.
5. Press the Status Key to return to the Status screen and select another signal to verify.
Or
Press the Cancel Key to return to the Command screen.

Executing Presets
7
CP-10 Instruction Manual
Executing Presets
Global & Local Presets Overview
Global and local presets are predefined sets of switches that can easily be executed.
Local Presets
A local preset is a predetermined set of switches on a particular level (virtual matrix) that are routed
simultaneously. They are stored in each enclosure’s configuration file and can be executed at any time.
Local presets are not programmed (defined) at the factory. To program them, use XNConnect (see the
XNConnect Help file) or contact your AMX representative (for contact information, see page 18). Once
the local presets have been defined as part of the configuration file, the new file must be loaded to the
system’s CPU (see the XNConnect Help file).
Global Preset
A global preset is a snapshot of an entire system’s state which enables that system state to be replicated
at a later time. The system state includes all current signal routings (regardless of the number of levels
involved) and any digital gain and/or volume settings. Before defining a Global Preset, route the system
to the desired state (including audio settings if applicable). A global preset number is assigned to a
system state during runtime using the CP-10 Control Panel (or BCS commands) and is stored in the
switcher’s non-volatile memory. That system state can then be restored at any time by selecting the
assigned global preset number.
Note: Global presets cannot be defined (created) in XNConnect.
Since the CP-10 Remote Control Panel can be used to operate different types of matrix switchers, check
the product documentation for any limitations to the number of supported global presets.
We strongly recommend keeping track of the number used and the system’s routing state for each global
preset. If another system state is assigned a previously used number, the former state will be
automatically overwritten.
Caution: If the system is reconfigured, global presets may be lost, depending on the method used to
load the new configuration file (see the XNConnect Help file).

Executing Presets
8CP-10 Instruction Manual
Executing Local Presets
Note: Executing a local preset does not change any system routings that are not part of the preset.
Make sure the CP-10 is on the level (virtual matrix) where the local preset resides.
To return to the Command screen at any time, press the Cancel Key.
The example below executes Local Preset 6 on Level 0.
To execute a local preset:
1. At the Command screen, press the Preset Key.
The Global preset screen appears.
2. Press the Level Key to access the Local Preset screen
The Local preset screen appears with the cursor after the Level prompt.
3. Enter “0” for the level.
Caution: Before selecting multiple presets, make sure all the presets switch on the same level.
4. Press the Preset Key again and enter “6.”
When entering multiple presets, separate the numbers by pressing the Space Key after each entry.
5. Press the Take Key.
Local Preset 6 is executed and the system returns to the Command screen.

Executing Presets
9
CP-10 Instruction Manual
Defining Global Presets
To return to the Command screen at any time, press the Cancel Key.
The example below defines Global Preset 3, and the example on page 10 executes Global Preset 3.
To define a global preset:
1. Route the system to the desired state.
2. At the Command screen, press the Preset Key.
The Global Preset screen appears.
3. Press the Preset Key again.
The program prompt appears with the cursor after the prompt.
Note: From the Global Preset screen, press the Preset key to toggle between the Program prompt
and the Execute prompt.
4. Enter “3” as the number to be associated with the current system state.
5. Press the Take Key.
The current system state can now be recalled at any time by executing Global Preset 3.
The system returns to the Command screen.
Note: We strongly recommend keeping track of the numbers and system state routings used for
global presets. If another system state is assigned to a previously used number, the former state will
be automatically overwritten.

Executing Presets
10 CP-10 Instruction Manual
Executing Global Presets
To return to the Command screen at any time, press the Cancel Key.
Note: When you execute a global preset, the system routes the switches immediately.
To execute a global preset:
1. At the Command screen, press the Preset Key.
The Global Preset screen appears with the cursor after the Execute prompt.
2. Enter “3.”
3. Press the Take Key.
Global Preset 3 is executed and the system returns to the Command screen.

Checking the Software Version
11
CP-10 Instruction Manual
Checking the Software Version
Use the following steps to check the software version of the CP-10 Control Panel.
To check the software version:
1. Press the Cancel Key.
2. At the Command screen press the Program Key.
The Software Version screen appears.
Current software version number

Installing a CP-10 Remote Control Panel
12 CP-10 Instruction Manual
Installing a CP-10 Remote Control Panel
This chapter covers rack installation for the CP-10 Remote Panel (FG1090-216), as well as instructions
for linking the panel to an enclosure. When the installation is complete, execute a test switch to make
sure the system is working properly (see page 15).
General Specifications
Rear View
Parameter Value
Cable for XNNet
Communications Two-conductor, 20 AWG, 7/28 strand cable with a drain wire or shield, such as Alpha 2412C (customer supplied)
Maximum length of cable: 1000 ft. (305 m) total, including linked panels
Power +7 VDC to +12 VDC @ 500 mA
Operational Temperature 32° F to 110° F (0° C to 43° C)
Humidity 0 to 90% non-condensing
Dimensions 1.0 in. (2.54 cm) depth
18.9 in. (48.0 cm) width with mounting ears
5.2 in. (13.21 cm) height, 3 RU
Weight Approximately 2 lb (0.91 kg) per panel
FIG. 4 Rear view of CP-10 Remote Panel
Power connector Comm Link connector

Installing a CP-10 Remote Control Panel
13
CP-10 Instruction Manual
Connecting to AMX AutoPatch Matrix Switcher
Communication Cable Requirements
 Two-conductor, 20 AWG, 7/28 strand cable with a drain wire or shield, such as Alpha 2412C
(customer supplied)
Maximum length of cable: 1,000 ft. (305 m) total, including linked panels
 AMX AutoPatch pigtail (provided)
To connect a CP-10 Remote to an AMX AutoPatch Matrix Switcher:
1. Attach the two wires of the AMX AutoPatch pigtail to the communication cable.
2. On the rear of the panel, plug the AMX AutoPatch pigtail into the Comm Link connector (FIG. 5).
3. On the matrix switcher’s CPU, unplug the REMOTE (XNNet) connector (for REMOTE connector
location, see the matrix switcher documentation).
4. Loosen the two outer screws on the connector.
5. Insert the two wires from the CP-10 Remote into the two outer slots of the REMOTE connector on
the matrix switcher, leaving the center slot empty (FIG. 6).
Note that either wire can go into either of the outer slots.
6. Tighten the screws and plug the connector back into the CPU.
FIG. 5 Plug pigtail into the Comm Link
FIG. 6 Insert wires into REMOTE connector on enclosure
AutoPatch pigtail (provided)
Comm cable (customer supplied)

Installing a CP-10 Remote Control Panel
14 CP-10 Instruction Manual
Applying Power
Power Requirements
 AMX AutoPatch wall transformer
Or
 +7 VDC to +12 VDC @ 500 mA
Important: Always use a UL approved power source. Be sure to check the power source
documentation for information specific to that power source.
The instructions below are for using the (optional) AMX AutoPatch wall transformer. If you use the
AMX AutoPatch transformer, the side of the wire with the white stripe is positive and the other side is
ground.
To apply power to the CP-10 Remote using the wall transformer:
1. Unplug the CP-10 Remote’s power connector.
2. Loosen the ground and positive screws.
3. Insert the power cable ground and positive wires into the slots (FIG. 7) and tighten the screws.
4. Plug the power connector back into the CP-10 Remote.
5. Install the CP-10 Remote in a rack (see page 15) or other permanent location before plugging the
transformer into the power source.
FIG. 7 Remove power connector, wire it, and replace
Positive
Ground

Installing a CP-10 Remote Control Panel
15
CP-10 Instruction Manual
Rack Installation
CP-10 Remote Panels are designed to fit in a standard EIA 19 in. (48.26 cm) rack.
Once the CP-10 Remote is wired, follow the rack installation instructions below.
Tip: When placing control panels, keep in mind that the optimal viewing angle is at eye level.
To install the CP-10 Remote in a rack:
1. Insert the wired panel through the rear of the rack.
2. Attach with front-mounting screws to hold it firmly in place (FIG. 8).
3. Apply power to the panel.
4. Wait briefly for the system to establish communication with the remote panel.
Execute a test switch to make sure the system is working properly (see below). If the system is not
working properly, check all system connections and retry the test switch before contacting technical
support (for contact information, see page 18).
Executing a Test Switch
We recommend completing the installation by executing a test switch routing Input 1 to Output 2 on the
level designated by the enclosure’s “Connector Guide” (the following example uses Level 0).
To execute a test switch:
1. At the Command screen, press the Change Key.
The Change screen appears.
FIG. 8 Place in rack and fasten with mounting screws

Installing a CP-10 Remote Control Panel
16 CP-10 Instruction Manual
2. Press the Level Key and enter “0.”
3. Press the Input Key and enter “1.”
4. Press the Output Key and enter “2.”
5. Press the Take Key.
Input 1 is routed to Output 2, and the system returns to the Command screen.
If the system is not working properly, check all system connections and retry the test switch before
contacting technical support (see page 18).

Appendix A – System Error Codes
17
CP-10 Instruction Manual
Appendix A – System Error Codes
This appendix contains an overview of common error codes that can appear on a CP-10 Control Panel,
provides basic troubleshooting strategies, and gives technical support contact information.
Common System Error Codes
The table below lists the error code, the name of the code, the meaning of the code, and some basic
troubleshooting strategies (additional troubleshooting strategies are included on page 18). The codes in
the table are not intended to be comprehensive. If an error code appears that is not listed, note the
specific number and contact technical support (for contact information, see page 18).
The first letter of the error code indicates the following:
E = Error
W = Warning
A = Alarm* (requires immediate attention)
I = Information*
* Because these codes very rarely appear, they are not included in the table.
Error
Code
Name Meaning Troubleshooting Strategies
E01000A Enclosure
timeout error One or more of the enclosures in a multi-enclosure system did not
acknowledge a control operation
command.
• Resend the command.
• Check the Status LED on the rear of each
enclosure. If any are red, contact
technical support.
• Check the power indicators.
• Check the link connections between
enclosures.
EFF8002 Enclosure
timeout error The operation was not completed before the timer expired. • Resend the command.
• Check the power indicators.
• Check the link connections in
multi-enclosure systems.
• Check that the level used in the command
was valid.
E01DFFF Audiorequest
error A volume or gain request was made on a level that does not
switch audio.
• Resend the command on a level that
includes audio.
W010005 Sync timeout
warning The system did not receive the vertical interval sync signal. Note
that the switch occurred, but not at
the sync interval.
• Resend the command.
• Check the sync cable connections.
• Check the HyperTerminal splash screen to
verify that sync is enabled (see the
vertical interval sync board information in
the matrix switcher’s manual).
• Check that the sync signal from the
generator is being received by the vertical
interval sync board.
• Power the system down and check sync
board alignment and seating.