AMX D-1901-PAN Parts list manual

Operation/Reference Guide
Touch Panels
MXT/D-1901-PAN
19.4" Modero X Series® G5 Panoramic Tabletop Touch Panel
19.4" Modero X Series® G5 Panoramic Wall Touch Panel
Initial Release: 3/19/2013

AMX Limited Warranty and Disclaimer
This Limited Warranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Partner which
include AMX Dealers, Distributors, VIP’s or other AMX authorized entity.
AMX warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of
purchase, with the following exceptions:
• Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay compo-
nents are warranted for a period of one (1) year.
• Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year.
• AMX lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long
as the AMX lighting products are under warranty. AMX also guarantees the control of dimmable loads that are properly con-
nected to our lighting products. The dimming performance or quality there of is not guaranteed, impart due to the random combi-
nations of dimmers, lamps and ballasts or transformers.
• AMX software is warranted for a period of ninety (90) days.
• Batteries and incandescent lamps are not covered under the warranty.
• AMX AutoPatch Epica, Modula, Modula Series4, Modula CatPro Series and 8Y-3000 product models will be free of defects in
materials and manufacture at the time of sale and will remain in good working order for a period of three (3) years following the
date of the original sales invoice from AMX. The three-year warranty period will be extended to the life of the product (Limited
Lifetime Warranty) if the warranty card is filled out by the dealer and/or end user and returned to AMX so that AMX receives it
within thirty (30) days of the installation of equipment but no later than six (6) months from original AMX sales invoice date. The
life of the product extends until five (5) years after AMX ceases manufacturing the product model. The Limited Lifetime Warranty
applies to products in their original installation only. If a product is moved to a different installation, the Limited Lifetime Warranty
will no longer apply, and the product warranty will instead be the three (3) year Limited Warranty.
All products returned to AMX require a Return Material Authorization (RMA) number. The RMA number is obtained from the AMX
RMA Department. The RMA number must be clearly marked on the outside of each box. The RMA is valid for a 30-day period. After
the 30-day period the RMA will be cancelled. Any shipments received not consistent with the RMA, or after the RMA is cancelled, will
be refused. AMX is not responsible for products returned without a valid RMA number.
AMX is not liable for any damages caused by its products or for the failure of its products to perform. This includes any lost profits, lost
savings, incidental damages, or consequential damages. AMX is not liable for any claim made by a third party or by an AMX Autho-
rized Partner for a third party.
This Limited Warranty does not apply to (a) any AMX product that has been modified, altered or repaired by an unauthorized agent or
improperly transported, stored, installed, used, or maintained; (b) damage caused by acts of nature, including flood, erosion, or earth-
quake; (c) damage caused by a sustained low or high voltage situation or by a low or high voltage disturbance, including brownouts,
sags, spikes, or power outages; or (d) damage caused by war, vandalism, theft, depletion, or obsolescence.
This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort claim (including
negligence and strict product liability), a contract claim, or any other claim. This limitation of liability cannot be waived or amended by
any person. This limitation of liability will be effective even if AMX or an authorized representative of AMX has been advised of the
possibility of any such damages. This limitation of liability, however, will not apply to claims for personal injury.
Some states do not allow a limitation of how long an implied warranty last. Some states do not allow the limitation or exclusion of inci-
dental or consequential damages for consumer products. In such states, the limitation or exclusion of the Limited Warranty may not
apply. This Limited Warranty gives the owner specific legal rights. The owner may also have other rights that vary from state to state.
The owner is advised to consult applicable state laws for full determination of rights.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX MAKES NO OTHER WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX
EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT
MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. EXCEPT AS OTHERWISE LIMITED
BY APPLICABLE LAW, AMX RESERVES THE RIGHT TO MODIFY OR DISCONTINUE DESIGNS, SPECIFICATIONS, WARRAN-
TIES, PRICES, AND POLICIES WITHOUT NOTICE.

Table of Contents
i
MXD/T-1901-PAN 19.4" Modero X Series® G5 Touch Panels
Table of Contents
Modero X Series® G5 Touch Panels ...................................................................1
Overview .................................................................................................................. 1
Features.................................................................................................................... 1
Modero X Dealer Benefits ........................................................................................ 1
Modero X Customer Benefits ................................................................................... 1
MXT-1901-PAN......................................................................................................... 2
Connector Locations........................................................................................................ 5
Memory ........................................................................................................................... 5
Basic Operation ............................................................................................................... 5
Powering on the MXT-1901-PAN .................................................................................... 5
Microphone............................................................................................................... 5
Audio/Video Capabilities................................................................................................. 5
MXD-1901-PAN ........................................................................................................ 6
Memory ........................................................................................................................... 9
Basic Operation ............................................................................................................... 9
Powering on the MXD-1901-PAN.................................................................................... 9
Microphone ..................................................................................................................... 9
Audio/Video Capabilities................................................................................................. 9
MXD/T-1901-PAN Features ...................................................................................... 9
Configuration .................................................................................................................. 9
NFC ................................................................................................................................. 9
Cleaning the Touch Overlay and Case........................................................................... 10
Installation ........................................................................................................11
MXT-1901-PAN Installation..................................................................................... 11
Wiring Guidelines ................................................................................................... 11
Wiring a Power Connection........................................................................................... 12
A Note About Wall and Rack Installation................................................................ 12
Installation Recommendations....................................................................................... 13
MXD-1901-PAN Installation .................................................................................... 14
Installing the MXD-1901-PAN into a wall ...................................................................... 14
Wiring a Power Connection........................................................................................... 20
Configuration and Programming ......................................................................21
Modero X Series G5 Programming Guide .............................................................. 21
Upgrading Firmware .........................................................................................23
Overview ................................................................................................................ 23
Upgrading Firmware via USB Flash Drive ............................................................... 23
Load the Firmware on a USB Flash Drive ...................................................................... 23

ii MXD/T-1901-PAN 19.4" Modero X Series® G5 Touch Panels
Table of Contents
Transfer the Firmware File From the Flash Drive to the Touch Panel............................ 23
Removing All Data From The Touch Panel .................................................................... 24
Resetting the Touch Panel Settings to Factory Defaults ............................................... 24
Resetting to Factory-Installed Firmware........................................................................ 25
Installing Previous Firmware.......................................................................................... 25
Installing New Firmware From An External USB Stick................................................... 26
Installing Touch Panel Pages From An External Disk..................................................... 27
Removing User Pages From a Touch Panel ................................................................... 27
Upgrading Firmware Via NetLinx Studio (v3.4 or higher) ....................................... 27
Appendix: Troubleshooting ..............................................................................31
Overview ................................................................................................................ 31
Panel Doesn’t Respond To Touches .............................................................................. 31
Panel Isn’t Appearing In The Online Tree Tab ............................................................... 31
Can’t Connect To a NetLinx Master .............................................................................. 31
Only One Modero Panel In My System Shows Up ......................................................... 31

Modero X Series® G5 Touch Panels
1
MXD/T-1901-PAN 19.4" Modero X Series® G5 Touch Panels
Modero X Series®G5 Touch Panels
Overview
The most elegant interface designed specifically for dedicated room control has been significantly enhanced to include a
new G5 Graphic Engine to provide even faster and smoother animations and transitions, and we quadrupled the
processing power with a new Quad Core Processor. The Modero X Series G5 Touch Panels provide several industry
firsts including a beautiful, panoramic capacitive multi-touch screen that provides users access to multiple applications
with minimal navigation. It is hardware-ready for support of Near Field Communication™ (NFC) Technology to allow
personalization of the user experience and productivity enhancing capabilities through integration with NFC capable
personal devices. The distinctive, low-profile design is engineered to sit perfectly on a table without obstructing views.
Modero X Series G5 is the control surface that simply delivers more.
Features
G5 Graphics Engine and Quad Core Processing – The most powerful processing in the industry delivers
smooth gesturing, swiping, dynamic reordering, enhanced animation with transitions all at higher speeds for
an experience any user will enjoy.
Simplified Enterprise Touch Panel Updates – Deploy and update touch panel files from a network URL for
simplified company-wide updates.
Built-in Web Browser and Document Viewers – Conveniently simplifies accessing and presenting
documents during meetings.
Panoramic Control Surface – Combined with the new PanTastic UI, the panoramic touch panels take the
user experience to a whole new level with an impressive control surface to perform activities much in the
same way you use a computer – multi-tasking with dedicated spaces.
Latest Communication Technologies – HD video chat and conferencing using integrated camera (tabletop
and landscape versions only) and supports Near Field Communication (NFC) – short-range wireless
technologies that deliver peer-to-peer communication by 'sharing, pairing and transaction' between RF
devices like exchanging data/identities.
Enhanced Usability – HD video streaming.
Perfect From Any Angle – Includes In-Plane Switching (IPS), the latest technology in popular tablet/mobile
devices that delivers the widest viewing angles and the most accurate color reproduction on the market.
Modero X Dealer Benefits
Attract More Corporate Customers - The elegant design and simple beauty of the Modero X Series G5 will
create demand from both new and current customers.
Address Unique Requirements – With a panoramic profile, the Modero X Series G5 provides dealers with a
solution for uses where multiple applications must be viewed simultaneously.
Differentiate Yourself – The Modero X Series G5 offers design and technology features unmatched in the
industry.
Modero X Customer Benefits
Multi-Task Capability – The contemporary design provides a large control surface, which allows multiple
views for different activities such as presenting, controlling and previewing.
Simple to Use Interfaces – The capacitive multi-touch screen combined with intuitive user-interfaces makes
it easy for anyone to operate sophisticated meeting room equipment
Sleek, Low-Profile Design - The Modero X Series G5 is engineered to sit perfectly on a table without
obstructing views.

Modero X Series® G5 Touch Panels
2MXD/T-1901-PAN 19.4" Modero X Series® G5 Touch Panels
MXT-1901-PAN
The MXT-1901-PAN (FG5968-41) (FIG. 1) is ideal for boardrooms, conference rooms, or auditoriums where a
panoramic control surface is needed to provide access to multiple functions simultaneously while remaining elegantly
unobtrusive. In residences, it is perfect for kitchens, home theaters, or home offices where the panoramic control surface
can be used to manage systems throughout the house.
The MXT-1901-PAN features a 20.4" x 6.9" (519 mm x 175 mm), 20.4" (518 mm) diagonal display, with a viewable area
of 18.7" x 5.9" (475 mm x 151 mm), 19.4" (493 mm) diagonal.
The device communicates via Ethernet (10/100 port, RJ-45 connector, supported IP and IP-based protocols: UDP, TCP,
ICMP, ICSP, IGMP, DHCP, SSH, DNS, RFB for VNC, and HTTP) and USB (3 USB host 2.0, Type A ports).
The MXT-1901-PAN also supports Near Field Communication (NFC) technology (please see the NFC on page 9 for
more information).
FIG. 1 MXT-1901-PAN touch panel
FIG. 2 MXT-1901-PAN side view
Sleep/Settings Button
7"
(177 mm)
20 3/8"
(59 mm)
5 5/16"
(135 mm)
USB Ports (2)
Sleep/Settings Button
Cable Slot
7"
177 mm)

Modero X Series® G5 Touch Panels
3
MXD/T-1901-PAN 19.4" Modero X Series® G5 Touch Panels
MXT-1901-PAN Specifications
Power Requirements: 12VDC, 4.4A LPS: 2-pin, locking 3.5mm captive wire connector.
Power Consumption: • Full-On: 35 W (12 VDC, 2.9 A)
•Standby: 7 W (12 VDC, 0.6 A)
•Recommended minimum power supply: 4.4A (PSN4.4)
Front Panel Components:
NFC Transceiver: Antenna and transceiver for Near Field Communications device detection and interaction.
Light Sensor: Photosensitive light detector for automatic adjustment of the panel brightness.
Motion Sensor: Proximity detector to wake the panel when it is approached.
•Typical Range: 1 foot (30.48 cm)
•Maximum Range: 3 feet (91.44 cm)
•Range width: 10 degrees
LED Indicator: Camera active indicator.
Sleep/Settings Button: Single button on top of panel for placing panel in sleep mode, for powering off the panel,
and for accessing the Settings app.
Microphone: -42dB ± 3dB sensitivity FET microphone.
Speakers: 4 ohm, 2 Watt, 300Hz cutoff frequency.
Camera: HD 720P camera for video conferencing/video chat support.
Rear Panel Components:
USB connections: 2 easily accessible USB ports on rear of base, used for connection to keyboard, mouse,
or USB flash drive.
Underside Panel Components:
Ethernet 10/100 Port: 10/100 Base-T RJ-45 connector for Ethernet connectivity.
Left green LED: Lights On when the connection speed is 100 Mbps and turns Off when
the speed is 10 Mbps.
Right yellow LED: Lights On when the Ethernet cables are connected and
terminated correctly and then blinks when receiving Ethernet data packets.
Power Port: Locking 2-Pin, 3.5mm captive wire connector.
Micro-USB Port: Not implemented.
USB Port: 1 USB port, used for connection to keyboard, mouse, or USB flash drive.
Touch Panel Display:
Display Type: TFT Active Matrix Color LCD with In-Plane Switching (IPS) technology.
Size: 19.4" (492.8 mm) diagonal.
Viewing Angle: • Vertical: ± 88°
•Horizontal: ± 88°
Screen Resolution
(W x H): 1920x530
Aspect Ratio (W x H): 32x9
Brightness: 350 cd/m2
Contrast Ratio: 1000:1
Color Depth: 16,7M colors.
Backlight Type: LED
Touch Overlay: Projected Capacitive; Multi-touch support, 3 simultaneous max.
Communications:
Ethernet: 10/100 port, RJ-45 connector and cable. Supported IP and IP-based protocols:
UDP, TCP, ICMP, ICSP, IGMP, DHCP, SSH, DNS, RFB (for VNC), HTTP
USB: 3 - USB host 2.0, Type A ports.

Modero X Series® G5 Touch Panels
4MXD/T-1901-PAN 19.4" Modero X Series® G5 Touch Panels
MXT-1901-PAN Specifications (Cont.)
Communications (Cont.):
Near Field Communications
(NFC): Supports standards ISO/IEC 15693, ISO/IEC 14443A, ISO/IEC 14443B; Unique Identifier (UID), Typical Range =.25”, Max = .5"
Video:
Supported Video Codecs: • MPEG2-TS: MPEG-2 Main Profile @High Level up to 720p at 25 fps, H.264 (decode
only)
• MJPEG up to 720p at 25 fps (decode only)
Streaming/File Formats: MPEG-TS for H.264, MPEG2; HTTP for MJPEG
Audio:
Streaming/File Formats: WAV, MP3.
Intercom: Full Duplex VoIP* (see note)
Operating Environment: • Operating Temperature: 32° F to 104° F (0° C to 40° C)
• Storage Temperature: 4° F to 140° F (-20° C to 60° C)
• Humidity Operating: 20% to 85% RH
• Humidity Storage: 5% to 85% RH
Dimensions (HWD): 7" x 20 7/16” x 5 5/16” (177.8 mm x 519 mm x 134.6 mm)
Weight: 9.4 lbs (4.26 Kg)
Certifications: • FCC Part 15 Class B
• C-Tick CISPR 22 Class B
• CE EN 55022 Class B and EN 55024
• CB Scheme IEC 60950-1
•IC
• IEC/EN-60950
• RoHS/WEEE compliant
Included Accessories: • MXT-1901-PAN Installation Guide (93-5968-41)
• MXA-CLK Modero X Series Cleaning Kit (FG5968-16)
• 3.5mm Locking Captive Wire Connector (41-0002-SA)
• HPG-10 .75-inch HydraPort .75-IN. Grommet (FG570-01)
• Type A USB Covers (2)
• Tie Wrap for Power Source Ferrite
Other AMX Equipment: • MXA-MP, Modero X/S Series Multi Preview (FG5968-20)
• MXA-MPL, Modero X/S Series Multi Preview Live (FG5968-10)
• PSN4.4, Power Supply, 4.4 A, 3.5 mm Phoenix, 13.5 VDC (FG423-45)
• HPG-10-10K, 3/4" Mini-Grommet, 10-Pack (FG570-01-10K)
• MXA-USB-C USB Cover Kit (FG5968-18)
• MXA-STMK-19, Secure Table Mount Kit (FG5968-65)
*- Feature will be supported in a future firmware update

Modero X Series® G5 Touch Panels
5
MXD/T-1901-PAN 19.4" Modero X Series® G5 Touch Panels
Connector Locations
With the unit facing you, the two USB ports for peripherals are located on the rear right corner of the device (FIG. 3).
The power and Ethernet connectors, as well as an additional USB port are located on the bottom of the device.
Memory
The MXT-1901-PAN comes with 2GB of SDRAM and 16GB of Flash memory, neither of which can be upgraded. A
maximum of 12GB is available to the user for projects.
Basic Operation
The MXT-1901-PAN is operated using its integral touchscreen, as well as the Sleep/Settings button on the top of the
device (FIG. 1). If the device has gone into its Sleep Mode, a touch of the touchscreen or of the Sleep/Settings button
will reactivate it.
Powering on the MXT-1901-PAN
The MXT-1901-PAN may be powered on by touching and holding the Sleep/Settings button on the top of the device.
Microphone
The MXT-1901-PAN contains a built-in microphone above the touch screen for video and audio conferencing
capabilities. This microphone is concealed by the casing.
Audio/Video Capabilities
The MXT-1901-PAN has the capability of displaying multiple JPEG and PNG files at one time. The device also supports
streaming motion JPEG video (of the sort used by many IP and Web cameras), as well as MP3 and WAV audio files.
FIG. 3 MXT-1901-PAN USB port location
Type A USB Ports

Modero X Series® G5 Touch Panels
6MXD/T-1901-PAN 19.4" Modero X Series® G5 Touch Panels
MXD-1901-PAN
The MXD-1901-PAN 19.4” Modero X Series G5 Panoramic Wall Touch Panels (Portrait Wall Mount: FG5968-42;
Landscape Wall Mount: FG5968-43) are ideal for boardrooms, conference rooms, or auditoriums where a panoramic
control surface is needed to provide access to multiple functions simultaneously while remaining elegantly unobtrusive.
In residences, they are perfect for kitchens, home theaters, or home offices where the panoramic control surface can be
used to manage systems throughout the house.
The MXD-1901-PAN features a 20.4" x 6.9" (519 mm x 175 mm), 20.4" (518 mm) diagonal display, with a viewable
area of 18.7" x 5.9" (475 mm x 151 mm), 19.4" (493 mm) diagonal.
The device communicates via Ethernet (10/100 port, RJ-45 connector, supported IP and IP-based protocols: UDP, TCP,
ICMP, ICSP, IGMP, DHCP, SSH, DNS, RFB for VNC, and HTTP) and USB (2 USB host 2.0, Type A ports).
The MXD-1901-PAN also supports Near Field Communication (NFC) technology (please see the NFC on page 9 for
more information).
FIG. 4 MXD-1901-PAN, Landscape Wall Mount
FIG. 5 MXD-1901-PAN, Portrait Wall Mount
Sleep/Settings Button
Sleep/Settings Button

Modero X Series® G5 Touch Panels
7
MXD/T-1901-PAN 19.4" Modero X Series® G5 Touch Panels
MXD-1901-PAN Specifications
Power Requirements: 12VDC, 4.4A LPS: 2-pin, locking 3.5mm captive wire connector.
Power Consumption: • Full-On: 35 W (12 VDC, 2.9 A)
•Standby: 7 W (12 VDC, 0.6 A)
•Recommended minimum power supply: 4.4A (PSN4.4)
Front Panel Components:
NFC Transceiver: Antenna and transceiver for Near Field Communications device detection and interaction.
Light Sensor: Photosensitive light detector for automatic adjustment of the panel brightness.
Motion Sensor: Proximity detector to wake the panel when it is approached.
•Typical Range: 1 foot (30.48 cm)
•Maximum Range: 3 feet (91.44 cm)
•Range width: 10 degrees
LED Indicator: Camera active indicator
Sleep/Settings Button: Single button on edge of panel for placing panel in sleep mode, for powering off panel,
and for access to the Settings app.
Microphone: -42dB +- 3dB sensitivity FET microphone
Speakers: 4 ohm, 2 Watt, 300Hz cutoff frequency
Camera: HD 720P camera for video conferencing/video chat support.
Rear Panel Components:
Ethernet 10/100 Port: 10/100 Base-T RJ-45 connector for Ethernet connectivity.
Power Port: Locking 2-Pin, 3.5mm captive wire connector.
Micro-USB Port: Not implemented.
USB Ports (2): USB connectors used for keyboard and mouse connections, or for firmware uploads. Side
port may require right angle mating connector (not included) for some configurations.
Touch Panel Display:
Display Type: TFT Active Matrix Color LCD with In-Plane Switching (IPS) technology.
Display Size
(W x H): •Landscape: 20.4" x 6.9" (519 mm x 175 mm)
•Portrait: 6.9" x 20.4" (175 mm x 519 mm)
• 20.4" (518 mm) diagonal
Viewable Area
(W x H): •Landscape: 18.7" x 5.9" (475 mm x 151 mm)
•Portrait: 5.9" x 18.7" (151 mm x 475 mm)
• 19.4" (493 mm) diagonal
Viewing Angle: • Vertical: ± 89°
•Horizontal: ± 89°
Screen Resolution
(W x H): •Landscape: 1920x530
•Portrait: 530x1920
Aspect Ratio
(W x H): •Landscape: 18:5
•Portrait: 5:18
Brightness: 350 cd/m2
Contrast Ratio: 1000:1
Color Depth: 16,7M colors
Backlight Type: LED
Touch Overlay: Projected Capacitive; Multi-touch support, 3 simultaneous max.

Modero X Series® G5 Touch Panels
8MXD/T-1901-PAN 19.4" Modero X Series® G5 Touch Panels
MXD-1901-PAN Specifications (Cont.)
Communications:
Ethernet: 10/100 port, RJ-45 connector and cable. Supported IP and IP-based protocols:
UDP, TCP, ICMP, ICSP, IGMP, DHCP, SSH, DNS, RFB (for VNC), HTTP
USB: 2 - USB host 2.0, Type A ports
Near Field Communications
(NFC): Supports standards ISO/IEC 15693, ISO/IEC 14443A, ISO/IEC 14443B; Unique Identifier (UID), Typical Range = .25", Max = .5"
Video:
Supported Video Codecs: • MPEG2-TS: MPEG-2 Main Profile @High Level up to 720p at 25 fps, H.264 (decode
only)
• MJPEG up to 720p at 25 fps (decode only)
Streaming/File Formats: MPEG-TS for H.264, MPEG2; HTTP for MJPEG
Audio:
Streaming/File Formats: WAV, MP3
Intercom: Full Duplex VoIP* (see note)
Operating Environment: • Operating Temperature: 32° F to 104° F (0° C to 40° C)
• Storage Temperature: 4° F to 140° F (-20° C to 60° C)
• Humidity Operating: 20% to 85% RH
• Humidity Storage: 5% to 85% RH
Dimensions (HWD): •Landscape: 6.9" x 20.4" x 0.7" (175 mm x 519 mm x 19 mm)
•Portrait: 20.4" x 6.9" x 0.7" (519 mm x 175 mm x 19 mm)
Weight: 7.0 lbs (3.18 Kg)
Certifications: • FCC Part 15 Class B
• C-Tick CISPR 22 Class B
• CE EN 55022 Class B and EN 55024
• CB Scheme IEC 60950-1
•IC
• IEC/EN-60950
• RoHS/WEEE compliant
Included Accessories: • MXD-1901-PAN Quick Start Guide (93-5968-42)
• MXD-1901-PAN Installation Template (68-5968-02)
• MXA-CLK Modero X Series Cleaning Kit (FG5968-16)
• 3.5mm Locking Captive Wire Connector (41-0002-SA)
• MXD-1901-PAN Back Box (68-5968-02)
Other AMX Equipment • MXA-MP, Modero X/S Series Multi Preview (FG5968-20)
• MXA-MPL, Modero X/S Series Multi Preview Live (FG5968-10)
• PSN4.4, Power Supply, 4.4 A, 3.5 mm Phoenix, 13.5 VDC (FG423-45)
• CB-MXP19/20, Rough-In Box, Modero X Series Touch Panel, Panoramic 19/20
(FG039-15)
• MXA-CLK, Modero X/S Series Cleaning Kit (FG5968-16)
• MXA-USB-C, USB Port Covers for the Modero X Series Touch Panels (FG5968-18)
• MXA-RMK-19, Rack Mount Kit (FG5969-61)
• MXA-FMK-19, Flush Mount Kit (FG5968-69)
*- Feature will be supported in a future firmware update

Modero X Series® G5 Touch Panels
9
MXD/T-1901-PAN 19.4" Modero X Series® G5 Touch Panels
Memory
The MXD-1901-PAN comes with 2GB of SDRAM and 16GB of Flash memory, neither of which can be upgraded. A
maximum of 12GB is available to the user for projects.
Basic Operation
The MXD-1901-PAN is operated using its integral touchscreen, as well as the Sleep/Settings button on the top of the
device (FIG. 1). If the device has gone into its Sleep Mode, a touch of the touchscreen or of the Sleep/Settings button
will reactivate it.
Powering on the MXD-1901-PAN
The MXD-1901-PAN may be powered on by touching and holding the Sleep/Settings button on the top of the device.
Microphone
The MXD-1901-PAN contains a built-in microphone above the touch screen for video and audio conferencing
capabilities. This microphone is concealed by the casing.
Audio/Video Capabilities
The MXD-1901-PAN has the capability of displaying multiple JPEG and PNG files at one time. The device also
supports streaming motion JPEG video (of the sort used by many IP and Web cameras), as well as MP3 and WAV audio
files.
MXD/T-1901-PAN Features
Configuration
The MXT-1901-PAN and MXD-1901-PAN are equipped with a Settings app that allow you to set and configure various
features on the panels. For more information on connecting and configuring the touch panels to a network, please refer to
the Modero X Series G5 Programming Guide, available at www.amx.com.
NFC
Both the MXT-1901-PAN and the MXD-1901-PAN support Near Field Communications™ (NFC) Technology. NFC
technology facilitates making transactions, exchanging digital content, and connecting electronic devices with a touch.
NFC transmissions are short-range (from a touch to a few centimeters), working with existing contact-less card
technologies and containing built-in capabilities to support secure applications. By using NFC technology, users may
receive access to touch panels and touch panel pages through access badges and other card options.
The maximum range for the NFC antenna is 0.5" (12.7 mm), but the typical usage range is 0.25" (6.35 mm). The antenna
itself is accessible from the front of the panel, 3.25" (82.55 mm) from the left corner of the panel and 0.375" (9.53 mm)
from the top edge. When using an NFC device with the MXT-1901-PAN, you should align your device’s antenna with
the center of the touch panel’s antenna (FIG. 6).
Common Access Card (CAC) Support In MXT/D-1901-PAN
Card Type Card Unique Identifier
(UID) Card Data Personal Identity Verification (PIV) Card
holder UID
15693 8 byte UID Not Supported N/A
14443A Non-Gov't 4, 7 or 10 byte UID (1) Not Supported N/A
14443A Gov't 4, 7 or 10 byte UID (1) Not Supported (2) Not currently
14443B Non-Gov't 4 byte UID Not Supported N/A
14443B Gov't 4 byte UID Not Supported (2) Not currently
FeliCa Not Supported Not Supported N/A
(1) The UID can be a fixed unique number or a random number dynamically generated by the card.
(2) Requires contact card reader (not accessible via NFC)

Modero X Series® G5 Touch Panels
10 MXD/T-1901-PAN 19.4" Modero X Series® G5 Touch Panels
Cleaning the Touch Overlay and Case
Both the MXT-1901-PAN and the MXD-1901-PAN come with the MXA-CLK Modero X Series Cleaning Kit (FG5968-
16), which may be used to clean fingerprints and dirt from the device. This kit comes with cleaning cloths and a bottle of
cleaning fluid specifically for use with the device.
When cleaning the device, do not directly spray the device with cleaning fluid. Instead, spray the cloth and then apply
the cloth to the touch screen. Do NOT use abrasives of any type to clean the device, as abrasives may permanently
damage or remove the device’s finish.
FIG. 6 NFC antenna location on the MXT-1901-PAN
3.25" (82.55 mm)
0.375" (9.53 mm)
NFC antenna location
To facilitate NFC antenna access, you may want to add an icon to the panel’s
page(s), pointing to the location of the antenna on the panel.

Installation
11
MXD/T-1901-PAN 19.4" Modero X Series® G5 Touch Panels
Installation
MXT-1901-PAN Installation
Other than the two USB ports on the back of the device (FIG. 3), the power and data connectors for the MXT-1901-PAN
are located on the underside of the device (FIG. 7). The underside USB port, as well as the two rear USB ports, may be
used with a flash drive for page transfers or firmware upgrades. Any USB peripherals (mouse, keyboard, etc.) may be
connected to one of the two USB ports on the rear of the device.
The MXT-1901-PAN does not have individual channels on the base of the device to allow passage of cables from
underneath the base. Instead, it has one slot at the base to allow options on cable configuration, with channels for
securing power and Ethernet cables (FIG. 8).
Each channel side has slots for attaching tie-wraps to secure each cable. The ferrite on the power cable must be secured
with the included tie-wrap during installation to prevent the possibility of the panel not sitting flush on the table. Other
cables may be secured with tie-wraps if desired, but this is not necessary.
Wiring Guidelines
The MXT-1901-PAN uses a 12 VDC-compliant power supply to provide power to the panel via the 2-pin 3.5 mm captive
wire PWR connector. Use the previously provided power requirement information in the Specifications table on page 3
to determine the power draw. The incoming PWR and GND wires from the power supply must be connected to the
corresponding locations within the PWR connector.
FIG. 7 MXT-1901-PAN underside connectors
FIG. 8 Tie-wrap for power connector ferrite
Ethernet 10/100
Port
USB Port
12 VDC
Power Port
Tie-wrap channels
Tie-wrap
Ferrite
Apply power to the panel only after installation is complete.

Installation
12 MXD/T-1901-PAN 19.4" Modero X Series® G5 Touch Panels
Wiring a Power Connection
To use the 2-pin 3.5 mm captive wire connector with a 12 VDC-compliant power supply, the incoming PWR and GND
wires from the external source must be connected to their corresponding locations on the connector (FIG. 9). The
connector uses locking screws to insure a connection to the device, so make sure to insert and tighten the screws before
applying power.
1. Insert the PWR and GND wires on the terminal end of the 2-pin 3.5 mm captive wire cable. Match the wiring
locations of the +/- on both the power supply and the terminal connector.
2. Tighten the clamp to secure the two wires. Do not tighten the screws excessively; doing so may strip the threads and
damage the connector.
3. Verify the connection of the 2-pin 3.5 mm captive wire to the external 12 VDC-compliant power supply and apply
power.
A Note About Wall and Rack Installation
Some products are installed in areas of differing temperature and cooling methodologies. These include products
installed in walls, racks, cabinets, etc. Those areas may have different temperatures and/or cooling approaches that must
be taken into consideration to maintain the product within the specified operating temperature.
FIG. 10 shows an AMX device installed in a wall with a filled volume (such as with insulation or concrete), as well as
with a closed volume (such as between studs in an otherwise finished wall). The diagram shows how heat generated by
the device or other devices may have no way to escape, and may build up to levels that may affect device operation.
Connecting power to the MXT-1901-PAN should be done using the included 2-pin
3.5mm captive wire connector included with the device. This connector is retained
within its port with locking screws instead of the pins on each side of standard captive
wire connectors, and using force to insert a standard captive wire connector may
damage the device.
FIG. 9 NetLinx power connector wiring diagram
FIG. 10 Heat convection in filled or closed volume, limited or no convection
PWR +
GND -
To the Touch Panel
Power Supply

Installation
13
MXD/T-1901-PAN 19.4" Modero X Series® G5 Touch Panels
In FIG. 11, the diagram displays an AMX device in a typical rack mounting, with full air circulation around the front and
back of the device. In this case, the main concern is with heat building up between components, possibly to levels that
may affect device operation.
Installation Recommendations
During any installation, a lack of ventilation may produce conditions that may adversely affect the device’s operation. In
these circumstances, special care must be made to make sure that temperatures within enclosed areas do not exceed the
device’s maximum rated temperature.
FIG. 11 Heat convection in rack-mounted devices
While the outside temperature of the device may be at or below its maximum
operating temperature, special care must be taken before and during installation to
ensure that the maximum operating temperature is not exceeded within wall or rack
installation spaces.

Installation
14 MXD/T-1901-PAN 19.4" Modero X Series® G5 Touch Panels
MXD-1901-PAN Installation
The MXD-1901-PAN may be installed directly into a solid surface environment, using either solid surface screws or the
included locking tabs for different mounting options. Once installed, the MXD-1901-PAN is contained within a clear
outer housing known as the back box. This back box is removed when installing the device into a wall or when using the
optional Rough-In Box accessory (FG039-15).
Installing the MXD-1901-PAN into a wall
The MXD-1901-PAN comes with a clear plastic backbox (FIG. 12) designed to attach the panel to most standard wall
materials. This backbox has four locking tabs (two on top and two on bottom) to help lock the backbox to the wall. These
locking tabs are only extended AFTER the backbox is inserted into the wall. The backbox also has four slots for
accepting the temporary mounting posts mounted on the back of the device (FIG. 13 and FIG. 14).
FIG. 12 MXD-1901-PAN Back Box
Locking Tabs
Locking Tabs
Temporary Mounting Posts
Temporary Mounting Posts
When installing the backbox, make sure that the assembly is in the correct position
and in the correct place. Once the locking tabs are extended and locked into place,
removing the backbox may be difficult without having access to the back of the wall
or causing damage to the wall.
FIG. 13 Side view of installed MXD-1901-PAN (Landscape)
Wall
Temporary Mounting Posts
MXD-1901-PAN
(front)
Back Box
Back box knockouts

Installation
15
MXD/T-1901-PAN 19.4" Modero X Series® G5 Touch Panels
To install the back box:
1. Prepare the area by removing any screws or nails from the drywall before beginning the cutout process.
2. Since the cutout for the back box is off-center from the edges of the touch panel, use the MXD-1901-PAN
Installation Template (68-5968-02) to ensure proper placement (FIG. 15).
FIG. 14 Side view of installed MXD-1901-PAN (Portrait)
Wall
Back box
knockouts Locking tabs
MXD-1901-PAN
front)
In order to guarantee a stable installation of the MXD-1901-PAN, the thickness of the
wall material must be a minimum of .50 inches (1.27cm) and a maximum of .875
inches (2.22cm).
The maximum recommended torque to screw in the locking tabs on the plastic back
box is 5 IN-LB [56 N-CM]. Applying excessive torque while tightening the tab screws,
such as with powered screwdrivers, can strip out the locking tabs or damage the
plastic back box.

Installation
16 MXD/T-1901-PAN 19.4" Modero X Series® G5 Touch Panels
3. Cut out the surface for the back box.
4. Thread the incoming power and Ethernet wiring from their terminal locations through the surface opening (FIG. 16
and FIG. 17). Leave enough slack in the wiring to accommodate any re-positioning of the panel.
FIG. 15 MXD-1901-PAN Template
20.433"
519.00 mm)
6.89"
175.00 mm)
14.50"
368.30 mm)
5.69"
144.50 mm)
Using the included template to select the final placement of the back box is highly
recommended. The outside edges of the template are the same dimensions as the
touch panel, which allows you to troubleshoot possible conflicts with wall edges,
doors, and other potential obstacles.
Making sure that the actual cutout opening is slightly smaller than the provided
dimensions is highly recommended. This action provides the installer with a margin
for error if the opening needs to be expanded. Too little wall material removed is
always better than too much.
FIG. 16 MXD-1901-PAN Back Box installation (Landscape)
Cables routed
to wall opening
Knockouts
top)
Mounting screw
placement (optional)
Back box cutout
Outer edge of
back box
Locking tab