Animas inset 30 User manual

Features:
• Luer Lock™connector with integrated automatic insertion system
• Preset 30 degree insertion angle
• Soft, flexible 13mm Teflon cannula
• Needle size: 27 gauge
• Reversible connector with audible “click”
• 2 tubing lengths: 60 cm (23 in) and 110 cm (43 in)
• 3 colours (60 cm): blue, pink and grey
Benefits:
• All-in-one, for quick and convenient infusion set changes
• Designed for stable 30 degree insertion
• Easy connection/disconnection
• Easy to carry in a pocket or purse
• Convenient, built-in needle cover following use
inset®30
The first and only
all-in-one angled set

1 2 3
45 6
7
8
9
1
2 3
45 6
7 8 9
Pull the red tape to remove the seal. Pull off
the sterile paper. Do not touch the spring at
this stage. Hold on the lined indentations with
one hand and pull the lid off with the other.
CAUTION: Be careful not to bend or touch
the inset®30 introducer needle.
After connecting the tubing to the insulin
pump, prime the infusion set until insulin
dispenses from the tip. Place a finger in
front of the cannula housing and insert
the connector needle. Make sure the
connector locks with a “click”.
Remove the backing paper under the front
end. Massage the adhesive thoroughly
onto the skin.
IMPORTANT: Do not attempt to straighten
the adhesive if curled.
1 2 3
4
5
6
7 8 9
Make sure that the cannula stays in place:
Put your finger gently on the clear window
while removing the insertion device and
introducer needle. Pull it gently straight back.
Put the lid back on for disposal.
inset®30
All-in-one angled infusion set
Place your fingers on the lined indentation
on each side. Pull back the spring softly
until you hear a “click”. The needle
protector will lift up or peel off. Do not
touch or bend the needle.
1
2
3
45 6
7 8 9
Immediately before insertion, carefully
remove the needle protector. Be sure the
tape is not stuck on the introducer needle.
1 2
3
45 6
7 8 9
Secure the cannula with one finger on
the clear window. Carefully remove the
backing paper under the cannula housing
as shown.
1 2 3
45
6
7 8 9
1 2 3
45 6
7
8 9
1 2 3
45 6
7 8
9
Place your index finger on the top release
button and your thumb on the bottom
release button. Position inset®30 with
its legs level (flat) on the skin to ensure
an insertion angle of 30o. Make sure to
maintain a 30oangle while insertion and
gently squeeze once to insert inset®30.
1 2 3
4
5 6
7 8 9
30%
Animas®is a registered trademark used under licence by LifeScan Canada Ltd.
All other trademarks are property of their respective owners.
© 2014 LifeScan Canada Ltd., Burnaby, BC V5C 6S7 AW103-265A 06/2014
200 Whitehall Drive
Markham (Ontario) L3R 0T5
Phone: [phone]
Email: [e-mail]
Web: www.Animas.ca
Distributed in Canada by
NOTE: This guide only illustrates some of the steps to follow when inserting inset®30 and is not a substitute for reading the instructions
for use that come with the product.
1 2 3
45 6
7 8 9
FRONT BACK
Recommended
insertion sites
Item No. :
10039600 inset®30, 60 cm (23 in), 13 mm, grey
10039601 inset®30, 60 cm (23 in), 13 mm, blue
10039602 inset®30, 60 cm (23 in), 13 mm, pink
10039603 inset®30, 110 cm (43 in), 13 mm, grey
Cannula fill amount
13mm cannula = 0.70 units
To order inset®30, call Animas
Canada at 1-866-406-4844.