Animas OneTouch Ping User manual

Gather your supplies.
Pump Infusion Set IV Prep and Alcohol
Wipe (or 2 alcohol
wipes)
Cartridge Insulin Vial
How to Change Your OneTouch Ping®
Infusion Set and Cartridge
Wash your hands.
Clean top of insulin vial with alcohol wipe.
Page 1 of 2
1. Unscrew black cartridge cap from pump.
2. Thread tubing connector through small end of black cartridge cap.
3. Remove small, clear cap from cartridge.
4. Screw tubing connector onto cartridge.
Attach infusion set tubing to cartridge.
Black Cartridge Cap
>
1. Prepare cartridge for filling:
• Twist needle onto cartridge.
• Attach blue handle onto plunger end of cartridge.
• Move plunger in and out 2 or 3 times.
2. Fill cartridge with insulin:
• Remove needle cover.
• With insulin vial on hard, level surface, insert needle
through top of vial so needle points down.
• Push plunger the whole way in and hold plunger in place.
• Turn vial upside down so needle points up.
• Slowly pull plunger back to fill cartridge to amount needed.
3. Get air bubbles out of cartridge:
• Tap cartridge to move bubbles to needle end of cartridge.
• Slowly push plunger in until bubbles go into vial.
• Slowly pull plunger back to fill cartridge to desired amount.
• Remove bottle and recap needle.
4. Twist needle off cartridge and put small, clear cap on cartridge.
5. Remove blue handle. Set filled cartridge aside.
Fill your cartridge.
>
>
Small Clear Cap
>
>
Needle
Blue Handle
>
Plunger
Cartridge
Make sure tubing is NOT connected to site on body.

Prime your tubing.
MAIN MENU
Home
Bolus
Suspnd/Resum
History
Basal
Setup
Prime/Rewind
Status
(Please wait)
PRIME
Cancel
Be sure set is
disconnected
from your body.
Then select
Continue.
Continue
Insulin: 200U
until insulin
comes out
of end of tubing
Press and hold
DELIVER
PRIME
Cancel
Press AND HOLD
OK button
while priming
tubing.
Go Prime
Insulin: 200U
PRIMING
ACTIVE
Press AND HOLD
OK button
while priming
tubing.
>>------>>------>>------
Insulin: 177U
>>>
3118284B, © 2016 Animas Corporation 2016/03 Rx Only.
ezPrime
Main Menu
Rewind
Load Cart
Prime
Fill Cannula
o
o
o
o
Go
Rewind
REWIND MOTOR
Cancel
Disconnect
infusion set
from your body!
Go Rewind
REWIND
COMPLETE
Cancel
Load U100
cartridge.
Attach cap.
Select Continue.
Continue
Put in cartridge.
Screw on
cartridge
cap. Press
Make sure tubing is NOT connected to site when priming.
Prime/
Rewind
Press
Press
Press
(Please wait)
REWIND
ACTIVE
Please wait.
Full rewind
required.
<<------<<------<<------
LOAD
CARTRIDGE
ACTIVE
>>------>>------>>------
Please wait.
>
>
> >
>
Press
0U
> > >
2 : 27PM
Status
Basal Rate
0.025U/Hr
Insulin: 105U
Menu
Press
>
*Follow instructions that came with your meter.
Page 2 of 2
ezPrime
Main Menu
Rewind
Load Cart
Prime
Fill Cannula
n
n
n
o
Press
FILL CANNULA
Main Menu
Amount
Go
0.00 U
Enter correct amount for your infusion set: ____units.
Press twice to deliver.
>Check blood
glucose* in
2-3 hours to
make sure
new site
is working.
1. Wipe skin with IV Prep or alcohol wipe at new site. Let dry.
2. Insert your infusion set using the instructions that came with your
infusion set.
3. If not already connected, connect tubing to site on body. Listen for a click.
>
—>
Insert your infusion set.
Fill your cannula. No cannula fill needed if using steel needle infusion set.
If insulin does not
come out of end of
tubing, then ,
Prime, and repeat
Prime.