ANTAIRA LNP-101AG-T User manual

i
Industrial PoE Splitter for 10/100/1000T
Wide Operating Temperature
User Manual

ii
FCC Warning
This Equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy. It may cause harmful interference
to radio communications if the equipment is not installed and used in
accordance with the instructions. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CE Mark Warning
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.

iii
Content
FCC Warning ......................................................i
CE Mark Warning...............................................ii
Content ............................................................. iii
Introduction ........................................................1
Features................................................................... 1
Package Contents.................................................... 2
Hardware Description.........................................3
Physical Dimension.................................................. 3
Front Panel............................................................... 3
Top View .................................................................. 4
Wiring the Power Outputs........................................ 4
LED Indicators.......................................................... 5
Ports......................................................................... 5
Cabling..................................................................... 5
Mounting Installation..........................................6
DIN-Rail Mounting.................................................... 6
Wall Mount Plate Mounting......................................8
Hardware Installation .........................................9
Installation Steps...................................................... 9
Network Application .........................................10
Troubles shooting.............................................11
Technical Specification ....................................12

1
Introduction
The Industrial Power over Ethernet Splitter receives a unified PoE signal
(data and power) via UTP/STP cable, and then separates the data and
power onto two different outputs for non-PoE devices which is not
compliant with IEEE802.3af standard. The network device can accept the
power and Ethernet data from the Splitter.
Features
Supports 10/100/1000T for PoE in and Data out
Power Isolation and Short circuit protection for power output
Auto disconnection for over power voltage input
Supports Output power up to 12.95W at 24VDC
Wide-range Power Design
IP-30 Protection
DIN Rail and Wall Mount Design
Provides EFT protection 3,000VDC for power line
Supports 6,000 VDC Ethernet ESD protection

2
Package Contents
Please refer to the package content to verify them against the checklist
below.
Industrial PoE Splitter x 1
Pluggable block connector x 1
Wall-Mount rack x 2
User manual x 1
Compare the contents with the standard checklist above. If any item is
damaged or missing, please contact your local dealer for service.

3
Hardware Description
In this paragraph, we will introduce the hardware spec, port, cabling
information, and wiring installation.
Physical Dimension
Industrial PoE Splitter dimension (W x D x H) is 30mm x 95mm x 140mm
Front Panel
The Front Panel of the Industrial PoE Splitter is shown as below.
Front Panel of the Industrial PoE Splitter
LED Indicator
RJ-45 Port

4
Top View
The top panel of the Industrial PoE Splitter has one terminal block
connector of two DC power outputs.
Top Panel of the Industrial PoE Splitter
Wiring the Power Outputs
Please follow the steps below to insert the power wire.
Insert the positive and negative wires into the V+ and V- contacts on the
terminal block connector.
Note
The wire gauge for the terminal block should be in the range
between 12~24 AWG.

5
Tighten the wire-clamp screws for preventing the wires from loosing.
LED Indicators
LED Status Meaning
Power Green Power is active
Off No power inputs
Ports
RJ-45 ports: 10/100/1000Mbps ports are auto-sensing for 10Base-T,
100Base-TX, or 1000Base-T connections.
Data pins for PoE IN port: 1, 2, 3, 6, 4, 5, 7, and 8
Power pins for PoE IN port: 4, 5 (V+); 7, 8 (V-) or 1, 2 (V+); 3, 6 (V-);
Data pins for DATA OUT port: 1, 2, 3, 6, 4, 5, 7, and 8
Power output (located on the top side): 1 x 6 pin terminal block
Cabling
Use the four twisted-pair, Category 5e cabling for RJ-45 port connection.
The cable between the splitter and the non-PoE device must be less than
100 meters (328 ft.) long.

6
Mounting Installation
DIN-Rail Mounting
The DIN-Rail is screwed on the Industrial PoE Splitter when out of factory.
If the DIN-Rail is not screwed on the Industrial PoE Splitter, please see the
following pictures to screw the DIN-Rail on the splitter. Follow the steps
below to hang the Industrial PoE Splitter.
1. Use the screws to screw the DIN-Rail on the rear side of the Industrial
PoE Splitter.
2. To remove the DIN-Rail, reverse step 1.

7
3. Insert the top of DIN-Rail into the track.
4. Then, lightly push the button of DIN-Rail into the track.
5. Check the DIN-Rail is tightly on the track.
6. To remove the Industrial PoE Splitter from the track, reverse steps
above.

8
Wall Mount Plate Mounting
Follow the steps below to mount the Industrial PoE Splitter with wall mount
plate.
1. Remove the DIN-Rail from the Industrial PoE Splitter; loose the screws
to remove the DIN-Rail.
2. Place the wall mount plates on the top & bottom side of the Industrial
PoE Splitter.
3. Use the screws to screw the wall mount plates on the Industrial PoE
Splitter.
4. Use the hook holes at the corners of the wall mount plates to hang the
Industrial PoE Splitter on the wall.
5. To remove the wall mount plates, reverse steps above.

9
Hardware Installation
In this paragraph, we will describe how to install the Industrial PoE Splitter
and the installation points for the attention.
Installation Steps
1. Unpack the Industrial PoE Splitter packing.
2. Check if the DIN-Rail is screwed on the Industrial PoE Splitter or not. If
the DIN-Rail is not screwed on the Industrial PoE Splitter, please refer
to DIN-Rail Mounting section for DIN-Rail installation. If the user
wants to wall mount the Industrial PoE Splitter, please refer to Wall
Mount Plate Mounting section for wall mount plate installation.
3. To hang the Industrial PoE Splitter on the DIN-Rail track or wall, please
refer to the Mounting Installation section.
4. Connect the UTP/STP cable between the PoE hub and the Industrial
PoE Splitter and the power LED on the Industrial PoE Splitter will light
up. Please refer to the LED Indicators section for indication of LED
lights.
5. Prepare the twisted-pair, straight through Category 5e/above cable for
Ethernet connection.
6. Insert one side of the RJ-45 cable into the Industrial PoE Splitter DATA
OUT port and another side to the non-PoE device.

10
Network Application
This segment provides the sample application to help user to have more
actual idea of Industrial PoE Splitter application. A sample application of
the Industrial PoE Splitter is shown as below.

11
Troubles shooting
Select the proper UTP/STP cable to construct user network. Use
unshielded twisted-pair (UTP) or shielded twisted-pair (STP) cable for
RJ-45 connections: 100ΩCategory 3, 4 or 5 cable for 10Mbps
connections, 100ΩCategory 5 cable for 100Mbps connections, or
100ΩCategory 5e cable for 1000Mbps connections. Also be sure
that the length of any twisted-pair connection does not exceed 100
meters (328 feet).
Diagnosing LED Indicators:To assist in identifying problems, the
Industrial PoE Splitter can be easily monitored through panel
indicators, which describe common problems the user may encounter
and where the user can find possible solutions.
If the power indicator does not light up when the power cable is
plugged in, you may have a problem with power cable. Then check
for loose power connections and power losses. If you still cannot
resolve the problem, please contact the local dealer for assistance.
If the Industrial PoE Splitter LED indicators are normal and the
connected cables are correct but the packets still cannot transmit.
Please check your system’s Ethernet devices configuration or status.

12
Technical Specification
The Industrial PoE Splitter technical specifications are as follows.
Standard
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3ab 1000Base-T
IEEE 802.2af Power over Ethernet
Connector
Data and power in:
1 x RJ-45 data pin 1, 2, 3, 6, 4, 5, 7, 8
Power pin 4, 5 (V+), 7, 8 (V-);
1, 2 (V+), 3, 6 (V-)
(Note: This PoE port should not be connected
to TNV-1 circuits.)
Data out:
1 x RJ-45 data pin 1, 2, 3, 6, 4, 5, 7, 8
Power out:
1 x 6-pin Terminal Block
Power Input 44 ~ 72VDC
Power Output 12.95W max. (0.539A @ 24VDC)
Power Output
Protection Power Isolation, Short Circuit Protection
Overload Current
Protection Present
LED Power (Green)

13
Network Cable
10/100Base-TX: 2-pair UTP/STP Cat. 3, 4, 5
cable
EIA/TIA-568 100-ohm (100m)
1000Base-T: 4-pair UTP/STP Cat. 5e cable
EIA/TIA-568 100-ohm (100m)
Power
Consumption 17.76 Watts@ 48VDC
Install Provides DIN rail kit and wall mount design
Operating
Temperature -40oC to 75oC
Operating
Humidity 5% to 95% (Non-condensing)
Storage
Temperature -40°C to 85°C
Case Dimension
Metal case IP-30, 30 mm (W) x 95 mm (D) x
140mm (H)
EMI
FCC Class A, CE EN61000-4-2 (ESD),
CE EN61000-4-3 (RS), CE EN-61000-4-4
(EFT), CE EN61000-4-6 (CS), CE
EN61000-4-8, CE, CE EN61000-6-2, CE
EN61000-6-4
Stability testing IEC60068-2-32 (Free fall), IEC60068-2-27
(Shock), IEC60068-2-6 (Vibration)
Safety UL, cUL, CE/EN60950-1