Aplex ARMPAC-6 Series User manual

ARMPAC-6XX Series
7”, 8”, 10.1”, and 12.1”Fanless i.MX6 DualLite ARM Cortex A9 HMI Series
User Manual
Release Date Revision
Oct. 2017 V1.4
®2017 Aplex Technology, Inc. All Rights Reserved. Published in Taiwan
Aplex Technology, Inc.
15F-1, No.186, Jian Yi Road, Zhonghe District, New Taipei City 235, Taiwan
Tel: [phone] Fax: [phone] URL: http://www.aplextec.com/zh/home.php

ARMPAC-6XX Series User Manual
1
Revision History
Reversion
Date
Description
1.0
2016/11/08
Official Version
1.1
2017/01/13
Add SOP of updating Firmware and Linux QT, and
update power consumption and net weight. Update
SBC-7112 motherboard manual to R1.2 version
1.2
2017/04/12
Modify power consumption data.
1.3
2017/07/19
Remove 5”
Add 15”, 15.6”
1.4
2017/10/20
Add motherboard version
Modify software/IP rating
Delete 15”, 15.6”

ARMPAC-6XX Series User Manual
2
Warning!________________________
Caution
Risk of explosion if the battery is replaced with an incorrect type.
Batteries should be recycled where possible. Disposal of used batteries must be in
accordance with local environmental regulations.
Disclaimer
This information in this document is subject to change without notice. In no event
shall Aplex Technology Inc. be liable for damages of any kind, whether incidental or
consequential, arising from either the use or misuse of information in this
document or in any related materials.
This equipment generates, uses and can radiate radio frequency energy and
if not installed and used in accordance with the instructions manual, it may cause
interference to radio communications. It has been tested and found to comply
with the limits for a Class A computing device pursuant to FCC Rules, which are
designed to provide reasonable protection against such interference when
operated in a commercial environment. Operation of this equipment in a
residential area is likely to cause interference in which case the user at his own
expense will be required to take whatever measures may be required to correct
the interference.
Electric Shock Hazard –Do not operate the machine with its back cover removed.
There are dangerous high voltages inside.

ARMPAC-6XX Series User Manual
3
Packing List
Accessories (as ticked) included in this package are:
□Adaptor
□Driver & manual CD disc
□Other.___________________(please specify)

ARMPAC-6XX Series User Manual
4
Safety Precautions
Follow the messages below to prevent your systems from damage:
◆Avoid your system from static electricity on all occasions.
◆Prevent electric shock. Don‘t touch any components of this card when
the card is power-on. Always disconnect power when the system is not
in use.
◆Disconnect power when you change any hardware devices. For instance,
when you connect a jumper or install any cards, a surge of power may
damage the electronic components or the whole system.

ARMPAC-6XX Series User Manual
5
Table of Contents
Revision History…………………………………………………………………………………………………….1
Warning!.............................................................…………………………….……………………2
Caution/Disclaimer………………….......………………………………………………………………………3
Packing List…………………………………….…………………………………………………....................4
Safety Precautions………………………………….……………….…..……………………....................5
Chapter 1 Getting Started
1.1 Features……..…………………..………………………...…………………………..6
1.2 Specifications…..………………...………………………………………………….6
1.3 Dimensions……..…………………....……………………………………………...8
1.4 Brief Description of ARMPAC-6XX…..….…..……………………….……10
1.5 VESA Mounting……………….…………..………..…...…………………..…..11
1.6 Panel Mounting…..………….…………..………..…...…………………..…..11
Chapter 2 Hardware
2.1 Motherboard Jumpers Setting and Connectors…………………...12
Chapter 3 Software images
3.1 Linux QT……………………………………....................……………………...18
3.2 Android………………………………………..................……………………...19
Figures
Figure 1.1: Dimensions of ARMPAC-607(P)..…….……….……………………….…..8
Figure 1.2: Dimensions of ARMPAC-608(P)………………… ……..………………….8
Figure 1.3: Dimensions of ARMPAC-610(P) ……………………………………..…….9
Figure 1.4: Dimensions of ARMPAC-612(P)…..……..…………………………………9
Figure 1.5: Front View of ARMPAC-6XX Series………………………………………10
Figure 1.6: Rear View of ARMPAC-6XX Series…………………………………….…10
Figure 1.7: ARMPAC-6XX Series VESA Mounting.……..……………….……….…11
Figure 1.8: ARMPAC-6XX Series Panel Mounting…..…………………………..11

ARMPAC-6XX Series User Manual
6
Chapter 1 Getting Started
1.1 Features
ARM based HMI
Fanless design
Flat front panel touch screen
Freescale i.MX6 DualLite/Quad (option) ARM Cortex A9 Processor
Onboard 1GB DDR3 DRAM
Onboard 4GB eMMC Flash
Wide range DC 9~36V power input
LED backlight LCD
Resistive touch windows/Projected capacitive touch
1.2 Specifications
ARMPAC-607(P)
ARMPAC-608(P)
ARMPAC-610(P)
ARMPAC-612(P)
System
CPU
Freescale i.MX6 DualLite/Quad(option) ARM Cortex A9 processor 1.0GHz
Memory
Onboard 1GB DDR3 DRAM
External IO Port
USB
2 x USB 2.0 type A
1 x USB 2.0 (Micro B type)
Serial/Parallel
1 x RS-232/422/485 DB-9, COM1
LAN
1 x LAN Port
Power
1 x 9~36V DC power input via 1 x 3-pin terminal block
Option
1 x RS-232/422/485 (TB-508C1)
WIFI/4G module via Mini-PCIe
Internal IO Port
Internal IO Port
1 x SIM card slot
1 x Micro SD slot
Storage Space
Storage
Onboard 4GB eMMC NAND flash
Expansion
Expansion Slot
1 x Mini-PCIe Slot full size
Display
Display Type
7”color TFT LCD
8”color TFT LCD
10.1”color TFT LCD
12.1”color TFT LCD

ARMPAC-6XX Series User Manual
7
Resolution
800x480
800x600
1024x600
800x600
Max. Color
262K
262K
262K
262K
Luminance
350
350
250
450
Contrast Ratio
400: 1
500: 1
500: 1
800: 1
Viewing Angle
140(H)/110(V)
140(H)/135(V)
140(H)/120(V)
160(H)/140(V)
Backlight Lifetime
40,000 hrs
40,000 hrs
25,000 hrs
50,000 hrs
Touch Screen –Resistive Touch Window Type
Interface
SPI
Light Transmission
Over 80%
Touch Screen –Projected Capacitive Type
Interface
USB
Light Transmission
Over 90%
Power
Power Input
DC 9~36V
Power
Consumption
MAX: 5.3W
(607)
MAX: 6.9W
(608)
MAX: 6.7W
(610)
MAX: 10.8W
(612)
Mechanical
Front Bezel Metal
Plastic/Panel Mount
Rear Panel Metal
Plastic/VESA 75
Plastic/VESA 100
Chassis Color
Pantone Cool Gray 11C
IP Rating
IP66 Front Panel
Dimensions
204 x 150 x 42.5
mm
231.1 x 176.1 x 45
mm
285 x 189 x 49.6
mm
319 x 245 x
51 mm
Net Weight
0.9 Kg
0.9 kg
1.4 Kg
1.5 Kg
Environmental
Operating
Temperature
0~50℃
Storage
Temperature
-20~60℃
Storage Humidity
10 to 90% @ 40℃, non-condensing
Certification
CE / FCC Class A
Operating System
Linux 3.0.35; Android 5.1.1

ARMPAC-6XX Series User Manual
8
1.3 Dimensions
Figure 1.1: Dimensions of ARMPAC-607(P)
Figure 1.2: Dimensions of ARMPAC-608(P)

ARMPAC-6XX Series User Manual
9
Figure 1.3: Dimensions of ARMPAC-610(P)
Figure 1.4: Dimensions of ARMPAC-612(P)

ARMPAC-6XX Series User Manual
10
1.4 Brief Description of ARMPAC-6XX
There are 7”, 8”, 10.1”, and 12.1”in fanless designed ARM based HMI, which
comes with flat front panel LED backlight touch designed. It is powered by Freescele
i.MX6 DualLite/Quad (option) ARM Cortex A9 processor, 1GB DDR3 onboard memory,
and 4GB eMMC NAND flash onboard. ARMPAC-6XX series is DC 9~36V wide range
power input and IP66 compliant front panel. The 7”, and 8”model can be VESA 75 x
75 mounted, and 10.1”, 12.1”can be VESA 100 x 100 mounted. The chassis color are
pantone cool gray 11C for plastic design in 7”, 8”, 10.1”, and 12.1”. Optional projected
capacitive touch screen supports 7H anti-scratch surface is ideal for use as PC-based
controller for industrial automation & factory automation.
Figure 1.7: Front View of ARMPAC-6XX Series
Figure 1.8: Rear View of ARMPAC-6XX Series

ARMPAC-6XX Series User Manual
11
1.5 VESA Mounting
The ARMPAC-6XX series is designed to be VESA mounted as shown in Picture. Just
carefully place the unit through the hole and tighten the given screws from the rear
to secure the mounting.
Figure 1.9: ARMPAC-6XX Series VESA Mounting
1.6 Panel Mounting
There are four holes located along the four sides of the HMI. Insert the clamp from
the four sides and tighten them with the nuts provided.
Figure 1.10: ARMPAC-6XX Series Panel Mounting

ARMPAC-6XX Series User Manual
12
Chapter 2 Hardware
2.1 Motherboard Jumpers Setting and Connectors
1. J5:
(Micro USB OTG 5P Connector), it is used to download and connect to Android App.
2. USB1:
(Double stack USB type A), Front USB connector, it provides 2 USB2.0 ports,
High-speed USB 2.0 allows data transfers up to 480 Mb/s, support USB full-speed and
low-speed signaling.
3. LAN1:
(RJ45 Connector), Front LAN port. One standard 10/100M RJ45 Ethernet port is
provided. Used Atheros AR8031 chipset, support LINK LED (green) and ACTIVE LED
(yellow).
4. MIO1:
(1.25mm Pitch 2*15 Connector), Including eight General-purpose input/output、a
group of SMBUS and two groups of serial communication interfaces, it provides a
group of self-programming interfaces to customers for flexible use.
Signal Name
Pin#
Pin#
Signal Name
PWRON
1
2
GND
POR_B
3
4
GND
5V_S0
5
6
GND
GPIO_IN0
7
8
GPIO_IN1
GPIO_IN2
9
10
GPIO_IN3
GPIO_OUT0
11
12
GPIO_OUT1
GPIO_OUT2
13
14
GPIO_OUT3
I2C3_SCL
15
16
5V_S0
I2C3_SDA
17
18
NC
GND
19
20
NC
UART1_TXD_B
21
22
GND
UART1_RXD_B
23
24
UART2_TXD
NC
25
26
NC
NC
27
28
UART2_RXD
GND
29
30
NC

ARMPAC-6XX Series User Manual
13
5. COM1
(Type DB9), Front serial port, standard DB9 Male serial port is provided to make a
direct connection to serial devices. Used the SP339E as the driver, which is an
advanced multiprotocol transceiver supporting RS-232, RS-485 and RS-422.
Pin#
Signal Name
1
DCD3-_422TX-_485-
2
RXD3_422TX+_485+
3
TXD3_422RX+
4
DTR3_422RX-
5
GND
6
NC
7
NC
8
NC
9
COM3_9PIN(connect to JP1)
6. CON2:
(2.0mm Pitch 2*8 Pin Socket), it provides a group USB2.0、SMBUS、UART and CANBUS
interfaces.
Signal Name
Pin#
Pin#
Signal Name
5V_S0
1
2
NC
USBDN_CON2_DM3
3
4
UART4_TXD
USBDN_CON2_DP3
5
6
UART4_RXD
GND
7
8
GND
GND
9
10
CAN1_TX
I2C2_SDA
11
12
CAN1_RX
I2C2_SCL
13
14
NC
3P3V_S0
15
16
NC
7.CON1：
(TF Card Socket), Support TF Card devices.
8. TOUCH1:
(2.00mm Pitch 2*5 Pin Header), Used the AR1021 as the touch screen controller
which supports resistive touch screen.

ARMPAC-6XX Series User Manual
14
Signal Name
Pin#
Pin#
Signal Name
Y-
1
2
SY-
SY+
3
4
Y+
X-
5
6
5WSX-
SX+
7
8
X+
M2(U17)
9
10
GND
9. SIM1:
(SIM Card Socket), Support SIM Card devices.
10. LVDS1:
(1.25mm Pitch 2*10 Connector, DF13-20DP-1.25V), For 18-bit LVDS1 output
connector.
Signal Name
Pin#
Pin#
Signal Name
VCC_LVDS0
1
2
VCC_LVDS0
GND
3
4
GND
LVDS0_TX0_N
5
6
LVDS0_TX0_P
LVDS0_TX1_N
7
8
LVDS0_TX1_P
LVDS0_TX2_N
9
10
LVDS0_TX2_P
NC
11
12
NC
LVDS0_CLK_N
13
14
LVDS0_CLK_P
GND
15
16
NC
BKLT_CTRL0
17
18
BKLT_EN_OUT0
VCC_BL0
19
20
VCC_BL0
11. LVDS2:
(1.25mm Pitch 2*10 Connector, DF13-20DP-1.25V), For 18/24-bit LVDS1 output
connector.
Signal Name
Pin#
Pin#
Signal Name
VCC_LVDS1
1
2
VCC_LVDS1
GND
3
4
GND
LVDS1_TX0_N
5
6
LVDS1_TX0_P
LVDS1_TX1_N
7
8
LVDS1_TX1_P
LVDS1_TX2_N
9
10
LVDS1_TX2_P
LVDS1_TX3_N
11
12
LVDS1_TX3_P
LVDS1_CLK_N
13
14
LVDS1_CLK_P

ARMPAC-6XX Series User Manual
15
GND
15
16
NC
BKLT_CTRL1
17
18
BKLT_EN_OUT1
VCC_BL1
19
20
VCC_BL1
12. INVT1:
(2.0mm Pitch 1*6 box Pin Header), Backlight control connector for LVDS1.
Pin#
Signal Name
1
VCC_BL0
2
VCC_BL0
3
GND
4
GND
5
BKLT_EN_OUT0
6
BKLT_CTRL0
13. BT1:
(1.0mm Pitch 1*2 box Pin Header), 3.0V Li battery is embedded to provide power for
RTC.
Pin#
Signal Name
1
VRTC
2
GND
14. INVT2:
(2.0mm Pitch 1*6 box Pin Header), Backlight control connector for LVDS2.
Pin#
Signal Name
1
VCC_BL1
2
VCC_BL1
3
GND
4
GND
5
BKLT_EN_OUT1
6
BKLT_CTRL1

ARMPAC-6XX Series User Manual
16
15. J20:
(1.0mm Pitch 1*2 box Pin Header), Reserved to connect switch reset button..
16. MPCIE1:
(Mini PCIe Socket 52Pin), mini PCIe socket, it is located at the top, it supports mini
PCIe devices with USB2.0 and SIM and SMBUS and PCIe signal. MPCIe card size is
30*30mm or 30*50.95mm.
17. JP1:
(2.0mm Pitch 2*3 Pin Header), COM1 jumper setting, pin1~6 are used to select signal
out of pin 9 of COM1 port.
JP1 Pin#
Function
Close 1-2
COM1 Pin9 = NC (option)
Close 3-4
COM1 Pin9 = +5V (default)
Close 5-6
COM1 Pin9 = +12V (option)
18. J1:
(2.0mm Pitch 1*3 Pin Header), LVDS1 jumper setting. It is used to provide 3.3V or 5V
voltage to VCC_LVDS0.
J1 Pin#
Function
Close 1-2
VCC_LVDS0 = 3.3V (option)
Close 2-3
VCC_LVDS0 = 5V (default)
19. J2:
(2.0mm Pitch 1*3 Pin Header), LVDS1 jumper setting. It is used to provide 5V or 12V
voltage to VCC_BL0.
J2 Pin#
Function
Close 1-2
VCC_ BL0 = 5V (option)
Close 2-3
VCC_ BL0 = 12V (default)
20. J3:
(2.0mm Pitch 1*3 Pin Header), LVDS2 jumper setting. It is used to provide 3.3V or 5V
voltage to VCC_LVDS1.
J3 Pin#
Function
Close 1-2
VCC_LVDS1 = 3.3V (option)
Close 2-3
VCC_LVDS1 = 5V (default)

ARMPAC-6XX Series User Manual
17
21. J4:
(2.0mm Pitch 1*3 Pin Header), LVDS2 jumper setting. It is used to provide 5V or 12V
voltage to VCC_BL1.
J4 Pin#
Function
Close 1-2
VCC_ BL1 = 5V (option)
Close 2-3
VCC_ BL1 = 12V (default)
22. SW2:
Dial Switch , it is used to select the voltage for BKLT_CTRL0 and BKLT_EN_OUT0.
SW2 Pin#
Function
Function
1-4
Close
Open(default)
BKLT_CTRL0 = 3.3V
BKLT_CTRL0 = 5V
2-3
Close
Open(default)
BKLT_EN_OUT0 = 3.3V
BKLT_EN_OUT0 = 5V
23. SW3:
Dial Switch, it is used to select the voltage for BKLT_CTRL1 and BKLT_EN_OUT1.
SW3 Pin#
Function
Function
1-4
Close
Open(default)
BKLT_CTRL0 = 3.3V
BKLT_CTRL0 = 5V
2-3
Close
Open(default)
BKLT_EN_OUT0 = 3.3V
BKLT_EN_OUT0 = 5V

ARMPAC-6XX Series User Manual
18
Chapter 3 Software images
3.1 Linux QT
1. Linux 3.0.35+QT4.85.

ARMPAC-6XX Series User Manual
19
3.2 Android
1. Android 4.2.2 (Kernel:3.0.35)