APO DK-9865 MK-II User manual
DIGITAL ACCESS CONTROL KEYPAD
DK-9865 MK-II
Programming & Installation Manual
FOR ELECTRIC LOCK
TABLE OF CONTENTS
INTRODUCTION
DESCRIPTION OF CONNECTION TERMINALS & INDICATORS
STANDARD PROGRAMMING SUMMARY CHART
SETTING & PROGRAMMING
SET KEYPAD TO SINGLE USER MODE (to whom it may require)
SPECIFICATIONS
APPLICATION EXAMPLE
APPLICATION HINTS FOR THE AUXILIARY FACILITIES
AUXILIARY INFORMATION
······························································································································· 3
······················································ 3-7
················································································································· 4
························································································································· 5
··········································································· 5
·········································································· 6-8
······································································································ 9-26
············································································································· 9
····························································································· 9
············· 9
······························································································ 10
··················································································· 10
······································································································· 11
························································································ 12-13
··································································································· 14
·············································································· 15
········································································ 16-17
·················································································· 18
················································································ 19
······································································································ 20
··················································································· 20
·················································································································· 21
································································································ 21
·········································································································· 22-23
·············································· 24-25
··························································· 24-25
·········································································· 25
······························································································································ 26
················································································································· 27
···································································· 28
············································································································· 29
2
INTRODUCTION
DESCRIPTION OF CONNECTION TERMINALS & INDICATORS
FIXING SCREWS x 2
GREEN (DOOR)
R (MAINS)EBMA
RED (INHIBIT)
Output 1 Door Bell
3 Amp Solid State 1 Amp Relay
3
1 - 2 : 12V DC --
3 - 4 : OUTPUT 1 --
Fail-Secure Electric
Lock in Default
6 - 7 : DOOR BELL
8 - EG IN --
13 - 14 : TAMPER N.C.
●
●
●
●
●
CONNECTION TERMINALS
4
THE LED INDICATORS
MAINS (AMBER)
DOOR (GREEN)
INHIBIT (RED)
BACK LIGHTING
THE PACIFIER TONES & THE LED INDICATING SIGNALS
NOTE:
*
**
STATUS TONES*LED SIGNALS
1. In programming mode
---
1 Beep
2 Beeps
5 Beeps
Continuous Beeps
---
1 second Long Beep **
ON
1 Flash
2 Flashes
5 Flashes
Continuous Flashes
1 Flash in 2 seconds interval
---
2. Successful key entry
3. Successful code entry
4. Unsuccessful code entry
5. DAP jumper not replaced
6. In standby mode
7. Output relay activated
●
●
●
5
A) Enter Programming Mode with Master Code (Exit-Factory Master Code: 0 0 0 0)
NOTE:
B) System Refreshing –
C) Code Entries –
1) Recording Master Code and User Codes – (No Default Codes)
2) Recording Super User Code – (No Default Codes)
3) Recording the Visitor Codes – (No Default Codes)
(Default: Momentary, 1-second)
STANDARD PROGRAMMING SUMMARY CHART
(default=1 second)
6
(Default: Fail-Secure)
(Default: 10 tries / 30 seconds)
(default)
(Default: 1 long beep)
H) User Code Entry Modes (Auto or Manual) – (Default: Manual)
(Default: ON)
(default)
J) Main LED Flashing ON-OFF – (Default: Flashing)
(default)
(default)
(default)
7
K) Egress Delay & Warning – (Default: Instant, No warning)
(default)
L) Exit Programming Mode
8
Criteria for Programming
MUST
DO NOT
Enter and Exit Programming Mode
key.
Master Code
3. Exit the programming mode by pressing the
NOTE:
●
●
●
●
●
SETTING & PROGRAMMING
DAP
ON OFF
9
New Master Code
NOTE:
●
●
●
Programming Example :
0 0 0 0
2. Program a new Master Code 3 2 8 9 for the keypad:
NOTE:
●3 2 8 9
●
3 2 8 9
2. key to clear all the current stored data
except the Master Code:
NOTE:
●(default)
System Refresh (Complete Data Refresh) (Refresh Code 8901)
10
User ID Entry of Code
Output 1
NOTE:
●
●00-99
●
●
●
Programming Example :
3 2 8 9
2. Program an User Code 8 3 2 1 for output 1 ---------- One of the 100 user codes (user ID: 00-99,
taking ID = 01 as example):
Operaon (Manual Code Entry Mode)
NOTE:
11
Super User Code
NOTE:
●
●
●
●
Programming Example :
3 2 8 9
2. Program 2 5 8 0 as Super User Code:
Operaon :
12
NOTE:
●
●
●This feature is recommended for Fail-safe locks only.
●
REMARK :
is in operation to hold the door lock open, all the User Codes
including Super User Code for Output 1 are temporarily suspended.
3)
NOTE:
●
●
●
13
One-Time
Time-Limit
User ID Entry of Code
NOTE:
●
●0-9
●
●
●
●
Programming Example :
3 2 8 9
2. Program a Visitor Code 1 3 7 8 at ID “0” for One-Time use:
3. Program a Visitor Code 2 3 0 8 9 at ID “1” with Time-Limit of 5 hours:
4. Program a Visitor Code 8 3 5 8 at ID “2” with Time-Limit of 10 hours:
Operaon :
14
Deleng Examples:
3289
a)
b)
c)
15
Time Length
A)
B)
C)
D)
NOTE:
●
Programming Options for Output 1 (See “Programming Summary Chart” Secon D for more informaon) :
Example:
8 3 2 18 3
5 4 3 2 15 4
Example:
5 4 3 2 15 4 3
9 2 7 0 5 39 2 7
16
Operaon :
8 3 2 1
8 3 2 1
8 3 2 1
NOTE:
●The purpose of the accelerated Code --
●
Super User Code
Programming Examples:
3 2 8 9
2. Set Output 1 in momentary mode of 5 seconds:
3. Set Output 1 in Start / Stop Mode:
4. Set Output 1 in Start / Stop Mode with 2-digit Accelerated Start Code:
17
Type of Lock
Programming Codes for Type of Locks:
Important Note to Installer:
de-energized
(Default)
energized
18
Programming Codes for Lock-Up Opons:
(Default)
Super User Code
Programming Examples:
3 2 8 9
19
Programming Opons:
(Default)
Programming Opons:
User Code Entry Modes (Auto or Manual) (Location 82)
(Default)
20
Table of contents
Other APO Keypad manuals
APO
APO DK-9866 MK-II User manual
APO
APO DK-9330 A User manual
APO
APO DK-9350 User manual
APO
APO DK-9823 MK-II User manual
APO
APO DK-9821 MK-II User manual
APO
APO DK-9522 MK-II User manual
APO
APO DK-9827 MK-II User manual
APO
APO DK-9520 MK-II User manual
APO
APO DK-9826 MK-II User manual
APO
APO DK-9820 MK-II User manual
