Honeywell 6162 Owner's manual

6162 SERIES KEYPAD PROGRAMMING SUPPLEMENT
Introduction
The 6162 series of keypads (6162, 6162V, 6162RF) provide the following features when used with control panels
having the firmware revisions listed below:
•Menu Mode Programming for easy programming of options typically used in a basic installation. See menu
Mode Programming section for details.
•Menu-Based User Code Programming to easily manage system users. The master user can do the following:
- add new users and user codes
- delete users
- assign user attributes, including authority level, access group, partition, and RF user number
Refer to the user guide included with the keypad for details on using menu-based user code programming.
Menu Mode Programming with 6162 Series Keypads
Menu mode programming provides easy programming of the following options:
•Entry of accounts and phone numbers
•Enabling various reports
•Setting entry & exit delays
•Setting alarm & fire sounder timeouts
•Assigning the Installer code
•Enabling the Auto-Stay feature
•Programming zone attributes
Menu mode programming is supported by the following
controls having the listed or higher firmware revision levels:
Control Firmware Rev. Level
VISTA-10P 4.16
VISTA-15P 9.16
VISTA-20P 9.16
VISTA-21iP 3.16
Navigation Keys for Menu Mode Programmin
g
Ke
y
Function
Settings Key Enter and exit Menu mode
programming.
Night Stay Advance to the next page.
[∗
∗∗
∗]
Advance to the next field. If at the
last field on a page, it advances to
the next page.
[#] Goes to the previous field. If at the
first field, goes to the previous page.
SETTINGS KEY
(ENTER MENU MODE
PROGRAMMING)
CLEAR
ENTRY
TOGGLE
ENTRIES
NO
YES
AWAY
STAY
NEXT PAGE
NEXT FIELD PREVIOUS FIELD
6162 Series_Keypad_1
To enter menu mode programming:
1. Enter panel programming mode (installer code + 800).
2. Press and hold the Settings key for 2 seconds
The word “communicating” appears briefly, then the first page of programming options appears.
Programming Menus
Menu mode programming consists of seven (7) pages of menus as follows:
Menu Menu Function
1 Phone Number & Account Number Programming
2 Reporting Options (alarm restore, trouble, bypass, AC loss, low battery, test, RF low battery)
3 System Reports (RF jam, cancel, event log full, exit error, open, close away, close stay)
4 Timing & Miscellaneous Options (exit/entry delays, alarm sounder timeout, fire alarm sound timeout, installer
code, auto-stay enable)
5 Zone Number (prompt to begin zone programming)
6 Zone Programming (zone type, report enable, partition, input type, serial number, response time, hardwire type,
zone descriptor)
7 Quit Menu Mode Programming

– 2 –
Menu 1: Phone Number & Account Number Programming
NOTES:
Menu mode programming limits the number of digits for
phone numbers and account numbers. If more than the
allowed digits are needed for either a phone number or
account number, use standard control panel
programming mode (installer code + 800) to make those
entries. Refer to the field number column for the
respective programming field in standard programming
mode.
Phone - Account
Primary xxxxxxxxxxxx
Secondary xxxxxxxxxxxx
Download xxxxxxxxxxxx
Pri Acc. P1 FFFF
Pri Acc. P2 FFFF
Sec Acc. P1 FFFF
Sec Acc. P2 FFFF
PHONE NUMBER & ACCOUNT NUMBER PROGRAMMNG
(To clear entries, use the Akey.)
Programming Option Entries Field
a. Primary Phone Number
Enter up to 12 digits, 0-9; B for “∗
∗∗
∗”; C for “#.”
∗41
b. Secondary Phone Number
See Primary phone number for entries.
∗42
c. Download Phone Number
See Primary phone number for entries.
∗94
d. Primary Account Number
Partition 1
Enter up to 4 digits; 0-9; B; C; D; AWAY for “E;” STAY for “F.”
∗43
e. Primary Account Number
Partition 2
See primary account number part. 1 for entries. ∗45
f. Secondary Account Number
Partition 1
See primary account number part. 1 for entries. ∗44
g. Secondary Account Number
Partition 2
See primary account number part. 1 for entries. ∗46
Menu 2: Enabling Reporting Options (for ADEMCO Contact ID®reporting only)
NOTES:
This menu lets you enable various reports if ADEMCO
Contact ID®format is being used. If another report
format is desired, use standard control panel
programming mode (installer code + 800) to program
these reports. Refer to the field number column for the
respective programming field in standard programming
mode.
Reporting: Event Rest
Alarm Rest N
Trouble Y N
Bypass N N
AC Loss Y N
Low Bat Y N
Test N N
RF Low Bat N N
REPORTS
Programming Option Event Restore Field Notes
a. Alarm Restore Report n/a ∗70 To enable/disable reports:
0 = No
1= Yes
To toggle an entry: Use the Dkey.
b. Trouble Report ∗60, ∗71
c. Bypass Report ∗61, ∗72
d. AC Loss Report ∗62, ∗73
e. Low Battery Report ∗63, ∗74
f. Test Report ∗64, ∗76
g. RF Low Battery Report ∗67, ∗75

– 3 –
Menu 3: Enabling System Reports (for ADEMCO Contact ID®reporting only)
NOTES:
This menu lets you enable various system reports if
ADEMCO Contact ID®format is being used by
selecting yes or no for each report. If another report
format is desired, use standard control panel
programming mode (installer code + 800) to program
these reports. Refer to the field number column for the
respective programming field in standard programming
mode.
System Reports
RF Jam N Cancel N
Log Full N
Exit Error N
P1 P2 P3
Open Report N N N
Close Away N N N
Close Stay N N N
System Reports
Programming Option Event Field Notes
a. RF Jam Report ∗22 To enable/disable a report:
0 = No
1= Yes
To toggle the entry, use the Dkey.
Dashed boxes: Indicates the entry is available
only for partitioned systems (ex. VISTA-20P,
VISTA-21iP).
b. Cancel Report ∗68
c. Event Log Full Report ∗89
d. Exit Error Report ∗59
e. Open Report
Part 1 Part 2 Part 3
∗65
f. Close Away Report
(Arm Away)
Part 1 Part 2 Part 3
∗66
g. Close Stay Report
(Arm Stay)
Part 1 Part 2 Part 3
∗66
Menu 4: Timing and Miscellaneous Options
NOTES:
This menu lets you set entry/exit delays, alarm
sounding timeouts, installer code, and enable the auto-
stay option. To program other options, use standard
control panel programming mode (installer code + 800).
Refer to the field number column for the respective
programming field in standard programming mode.
Timing / Misc P1 P2
Exit Delay 60 60
Entry 1 Delay 30 30
Entry 2 Delay 30 30
Alarm Sound Time: 4M
Fire Snd. Timeout N
Installer Code xxxx
Auto Stay: Part 1 & 2
Timing and Miscellaneous Options
Scroll Backward: Use the Ckey; Scroll Forward: Use the Dkey.
Dashed boxes: Indicates the entry is available only for partitioned systems (ex. VISTA-20P, VISTA-21iP).
Programming Option Entries Field Notes
a. Exit Delay | |
Part. 1 Part. 2
∗34
00 - 96 = 0 - 96 seconds
97 = 120seconds
SIA Controls: Entries less than 45 result in 45-sec. delay.
b. Entry Delay 1 | |
Part. 1 Part. 2
∗35
00 - 96 = 0 - 96 seconds 98 = 180seconds
97 = 120seconds 99 = 240seconds
SIA Controls: Entries less than 30 result in 30-sec. delay.
c. Entry Delay 2 | |
Part. 1 Part. 2
∗36 See Entry Delay 1 for entries.
d. Alarm Sounder (Bell)
Timeout
∗33
0= none 3= 12 min
1= 4 min 4= 16 min
2= 8 min
e. Fire Alarm Sound
Timeout
[Fire Snd. Timeout]
∗32
0= Yes - sound stops at timeout set in field ∗33
1= No - no timeout
f. Installer Code | | | ∗20 4 digits, 0000-9999
g. Auto-Stay ∗84 0= no 2= part. 2 only
1= part. 1 only 3= part. 1 & part 2

– 4 –
Menu 5: Enter Zone Number
NOTES:
This menu starts Zone Programming, which lets you
program basic zone attributes. Enter the desired zone
number at this prompt, then press [∗]. The Zone
Programming page (menu 6) appears.
When all zones have been programmed, enter 00 to
advance to the Quit menu.
Zone Number
Enter Zone No
01
Programming Option Entries Field
a. Zone Number Control Wired Zone RF Zones
Vista-20P and Vista-21iP: 01-08; 09-48†09-48; 49-64††
95, 96,99†††
Vista-15P: 01-06;09-24†09-34; 49-56††
95, 96, 99†††
Vista-10P: 01-06 09-24
95, 96, 99††† 49-56††
†
Zone Expander Zones; †† RF button zones; ††† Emergency zones
[∗
∗∗
∗] = continue programming the selected zone
00 = go to Quit menu
∗56
Menu 6: Zone Programming
NOTES:
Pressing [∗] at the Zone Number prompt displays the
Zone Programming page. To program additional zone
attributes, or to use any other menu mode of
programming, use standard control panel programming
mode (installer code + 800).
DISPLAY NOTE: Typical hardwired zone shown in the
example display. For wireless zones, the Resp / Config line is
replaced by the serial number entry line:
S/N Axxx – xxxx Loop x
Zone Programming #01
Type: 09 Fire
Send Report: Y Part 1
Input Type: Hardwired
Resp: 350mS Config: EOL
Library 000 000 000
Disp : xxxxxxxxxxxxxxxx
Zone Programming
Programming Option Entries Field Notes
a. Zone Type |
∗56
Enter the 2-digit Zone Type from the table below.
00 = Not used 07 = 24-Hr Audible 20 = Arm–STAY*
01 = Entry/exit #1 08 = 24-Hr Aux 21 = Arm–AWAY*
02 = Entry/exit #2 09 = Fire 22 = Disarm*
03 = Perimeter 10 = Interior w/Delay 23 = No Alarm Resp
04 = Int. Follower 12 = Monitor Zone 24 = Silent Burglary
05 = Day/Night 14 = Carbon Monoxide 77 = Keyswitch
06 = 24-Hr Silent 16 = Fire w/Verify 81 = AAV Mon. Zone
To disable the current zone, enter 00.
Press [∗] to advance.
b. Send Report ∗56 0= No – do not send report
1= Yes – send report
c. Partition
∗56
1= parition 1
2= partition 2
3= partitions 1 & 2
Applies only to partitioned controls.
Press [∗] to advance.
d. Input Type
∗56
For built-in hardwired zones, the input type
automatically displays “Hardwired.” For wireless
and auxiliary wired zones, select the input type:
2= Aux (Aux wired zone; ex. 4219, 4229)
3= RF. Trans. (supervised RF transmitter)
4= Unsupv. RF (unsupervised RF transmitter)
5= RF Button (Unsupervised Button RF)
Press [∗] to advance.

– 5 –
e. Serial Number | | | | | |
Serial Number
Loop ∗56
Manually enter the 7-digit serial number printed on
the label of the transmitter.
Press the [∗] key to move to the “Loop” position,
and then enter the loop number.
To delete an existing serial number, enter 0 in the
loop number field. The serial number will change to
0's. If 0 was entered in error, simply re-enter the
loop number or press [#], the serial number will
return to the display.
Press [∗] to advance.
f. Response Time
∗56
Applies only to hardwire zones 1-8.
0= 10mSec
1= 350mSec
2= 700mSec
3= 1.2 seconds
Press [∗] to advance.
g. Configuration
(Hardwire Type)
∗56
Applies only to hardwire zones 1-8.
0= EOL
1= NC
2= NO
3= zone doubling (ZD) (V20P/V21iP only)
4= double-balanced (DB) (V20P/V21iP only)
Press [∗] to advance.
h. Library
(Zone Descriptor)
word 1 word 2 word 3
∗82
For each descriptor word for this zone, enter the
3-digit number from the Vocabulary list.
(see Library list of descriptors on the back page or
in the controls’ Programming Guide)
Press [∗] to return to the Zone Number prompt to
program the next zone or advance to the Quit menu.
Menu 7: Quit Menu Mode Programming
NOTES:
Use this menu to exit Menu mode programming. After
exiting, the “Communicating” message appears
briefly, indicating the control is being updated with the
programmed information.
QUIT QUICK
PROGRAMMING MODE
1 – Exit – Allow Re-entry
2 – Exit – Block Re-entry
3 – Back to 1st Page
Quit Menu
Programming Option Entries Field Notes
a. Exit – Allow Re-Entry 1
∗99
Exits program mode and allows re-entry by:
Installer Code + 8 0 0, or pressing [∗] and [#] at the
same time within 50 seconds of powering up
b. Exit – Block Re-Entry 2
∗98
Exits programming mode and prevents re-entry by:
Installer Code + 8 0 0.
To reenter programming mode, the system must be
powered down, then powered up. Then press [∗]
and [#] at the same time within 50 seconds of
powering up.
For other ∗98 program mode lockout options, see
field ∗88 in standard control panel programming
mode (installer code + 800).
c. Back to 1st Page 3 -- Press 3 to return to the first page of Menu mode
programming.

LIBRARY LIST (Zone Descriptors)
000 (Word Space)
– A –
001 AIR
002 ALARM
∗
004 ALLEY
005 AMBUSH
006 AREA
007 APARTMENT
009 ATTIC
∗
010 AUDIO
– B –
012 BABY
∗
013 BACK
∗
014 BAR
016 BASEMENT
∗
017 BATHROOM
∗
018 BED
019 BEDROOM
∗
020 BELL
021 BLOWER
022 BOILER
023 BOTTOM
025 BREAK
026 BUILDING
– C –
028 CABINET
029 CALL
030 CAMERA
031 CAR
033 CASH
034 CCTV
035 CEILING
036 CELLAR
037 CENTRAL
038 CIRCUIT
040 CLOSED
∗
046 COMPUTER
047 CONTACT
– D –
048 DAUGHTERS
049 DELAYED
050 DEN
∗
051 DESK
052 DETECTOR
∗
053 DINING
∗
054 DISCRIMINATOR
055 DISPLAY
057 DOOR
∗
059 DOWN
060 DOWNSTAIRS
061 DRAWER
062 DRIVEWAY
064 DUCT
– E –
065 EAST
066 ELECTRIC
067 EMERGENCY
∗
068 ENTRY
069 EQUIPMENT
071 EXIT
∗
072 EXTERIOR
– F –
073 FACTORY
075 FAMILY
076 FATHERS
077 FENCE
079 FIRE
∗
080 FLOOR
∗
081 FLOW
082 FOIL
083 FOYER
084 FREEZER
085 FRONT
∗
– G –
089 GARAGE
∗
090 GAS
091 GATE
092 GLASS
093 GUEST
094 GUN
– H –
095 HALL
∗
096 HEAT
098 HOLDUP
099 HOUSE
∗
– I –
100 INFRARED
101 INSIDE
∗
102 INTERIOR
103 INTRUSION
– J –
104 JEWELRY
– K –
105 KITCHEN
∗
– L –
106 LAUNDRY
∗
107 LEFT
108 LEVEL
109 LIBRARY
∗
110 LIGHT
111 LINE
113 LIVING
∗
114 LOADING
115 LOCK
116 LOOP
117 LOW
118 LOWER
– M –
119 MACHINE
121 MAIDS
122 MAIN
∗
123 MASTER
∗
125 MEDICAL
∗
126 MEDICINE
128 MONEY
129 MONITOR
130 MOTHERS
131 MOTION
∗
132 MOTOR
– N –
134 NORTH
135 NURSERY
– O –
136 OFFICE
∗
138 OPEN
∗
139 OPENING
140 OUTSIDE
142 OVERHEAD
– P –
143 PAINTING
144 PANIC
∗
145 PASSIVE
146 PATIO
∗
147 PERIMETER
148 PHONE
150 POINT
151 POLICE
∗
152 POOL
∗
153 POWER
– R –
155 RADIO
156 REAR
157 RECREATION
159 REFRIGERATION
160 RF
161 RIGHT
162 ROOM
∗
163 ROOF
– S –
164 SAFE
165 SCREEN
166 SENSOR
167 SERVICE
168 SHED
∗
169 SHOCK
170 SHOP
∗
171 SHORT
173 SIDE
∗
174 SKYLIGHT
175 SLIDING
∗
176 SMOKE
∗
178 SONS
179 SOUTH
180 SPRINKLER
182 STATION
184 STORE
185 STORAGE
∗
186 STORY
190 SUPERVISED
∗
191 SUPERVISION
192 SWIMMING
193 SWITCH
– T –
194 TAMPER
196 TELCO
197 TELEPHONE
199 TEMPERATURE
200 THERMOSTAT
201 TOOL
202 TRANSMITTER
– U –
205 UP
206 UPPER
207 UPSTAIRS
∗
208 UTILITY
∗
– V –
209 VALVE
210 VAULT
212 VOLTAGE
– W –
213 WALL
214 WAREHOUSE
216 WEST
217 WINDOW
∗
219 WING
220 WIRELESS
– X –
222 XMITTER
– Y –
223 YARD
– Z –
224 ZONE (No.)
225 ZONE
∗
226 0
227 1
228 1ST
∗
229 2
230 2ND
∗
231 3
232 3RD
∗
233 4
234 4TH
235 5
236 5TH
237 6
238 6TH
239 7
240 7TH
241 8
242 8TH
243 9
244 9TH
Note: Italicized words followed by an asterisk indicate those words supported by the 6162V/6152V Voice Keypads
Ê800-14049V1IŠ
800-14049V1 7/13 Rev. A
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2013 Honeywell International Inc.
www.honeywell.com/security