APO DK-9823 MK-II User manual
MULTI-PURPOSE
DIGITAL ACCESS CONTROL KEYPAD
DK-9823 MK-II
Programming & Installation Manual
FOR ELECTRIC LOCK, INTER-LOCK
AND SECURITY SYSTEM INSTALLATIONS
TABLE OF CONTENTS
INTRODUCTION
DESCRIPTION OF CONNECTION TERMINALS & INDICATORS
(IV)
STANDARD PROGRAMMING SUMMARY CHART
SETTING & PROGRAMMING
SET KEYPAD TO SINGLE USER MODE (to whom it may require)
SPECIFICATIONS
APPLICATION EXAMPLE
APPLICATION HINTS FOR THE AUXILIARY FACILITIES
AUXILIARY INFORMATION
······························································································································· 3
······················································ 3-7
··············································································································· 4
························································································································· 5-6
·························································································································· 6
··········································································· 7
········································································ 8-10
······································································································ 11-26
············································································································· 11
····························································································· 11
············· 11
······························································································ 12
··················································································· 12
······································································································· 13
························································································ 14-15
·································································································· 16
··································································································· 17
·············································································· 18
····························································· 19-20
················································································ 21
················································································ 22
··························································································· 23
······································································································ 23
··················································································· 24
·················································································································· 24
································································································ 24
·········································································································· 25-26
·········································································· 26
············································· 27-28
··························································· 27-28
·········································································· 28
······························································································································ 29
············································································································ 30-32
······························································ 33-35
············································································································· 36
2
INTRODUCTION
DESCRIPTION OF CONNECTION TERMINALS & INDICATORS
Output 1 Output 2 Output 3 Door Bell
3 Amp Solid State 1 Amp Relay NPN Open Collector 50mA Tact Switch
INTRODUCTION
DK-9823 is an universal, self-contained digital access keypad oers eld proven reliability and cost eective solutions
for residential and commercial installations. It is designed for stand alone electric lock and inter-lock systems and
operates from a 12 to 24V AC/DC power supply. It is virtually compatible with any electric locking device. Apart
from that it is also the perfect choice for controlling security systems, automatic operators and machinery.
DK-9823 consists two application softwares of Single User Mode for the general Users, and Multi-User Mode for the
advanced Users. The system oers a 4 digit length user code with 10,000 combinations for each output in single user
mode; and 100 user codes for output1and 10 user codes each for output2and output3in length of 4-8 digits with
combinations of more than 100 million in multi-user mode. Operation options of Auto Code entry and Manual Code entry
are available in both two user modes. Programmed information that stored in the system are non-volatile in power failure.
The DK-9823 oers three outputs with the following facilities:
The connection facilities consist one set of terminal block mainly for Output1for door striking purpose; and one
set of wire harness for Output2and 3, and the auxiliary functions.
A Normally Open dry contact with maximum rating of 12VDC/50mA prepared as the triggering point of a low
power electronic door chime. DO NOT use this contact as a power path ofadoor bell.
A Normally Closed (N.C.) input terminal referring to ( ) ground. With the help of a normally closed magnetic
door switch, the system will monitor the position of the door and will give the following functions:
THE TERMINAL BLOCK
DOOR BELL
DOOR SENS DOOR POSITION SENSOR INPUT
-
CONNECTION FACILITIES
2
OUTPUT 1
5 Amp relay
OUTPUT 3
NPN Open Collector
OUTPUT 2
1 Amp relay
WHITE/ORANGE DURESS OUTPUT
YELLOW GREEN ( ) GND
BROWN INTERLOCK CONTROL
ORANGE OUTPUT1INHIBIT
WHITE/RED OUTPUT 3
OUTPUT 2
RELAY
PURPLE (N.C.)
YELLOW (+)
LIGHT BLUE ( )
GREEN (+)
GREY ( )
BLACK
RED
ALARM (RED) LED
DOOR (GREEN) LED
TAMPER
AUXILIARY (GREEN) LED ( ) WHITE
KEYPAD ACTIVE OR ALARM OUTPUTPINK
BLUE (N.O.)
WHITE/BROWN (COM)
116
215
314
413
512
611
710
98
DK-9823
ON OFF
DAP
KEY AL
K OR A
( ) ( )
12 24V
AC / DC
EG
IN
DOOR BELL
N.O.
DOOR
SENS
OUTPUT 1
N.C. COM N.O.
1 2 3 4 5 6 789 10 11 12 13 14 1516
DOOR BELL
N.O.
DOOR
SENS
EG
IN
(–) (+)
12V DC
(+) (–)
DOOR LOCK
AUXILIARY (RED) LED ( )
3
●
●
●
●
●
CONNECTION TERMINALS
1 - 2 : DOOR BELL
3 : DOOR SENS --
NOTE
1) Door Auto Re-lock
2) Door Forced Open Alarm and Warning
3) Door Propped-up Warning
4) Inter-lock Control
4 - 5 : 12V DC --
6 : EG IN --
7 - 8 : OUTPUT 1
Fail-Secure Electric Lock
in Default
4
NOTE:
1 -2 : TAMPER N.C
3 - 4, 5 - 6, 7 : DOOR LED, ALARM LED & AUXILIARY LED
"LED INDICATORS"
8 : K OR A O/P --
i) KEYPAD ACTIVE OUTPUT (K)
ii) ALARM OUTPUT (A)
9 -10 -11 : OUTPUT 2
12 : OUTPUT 3
13 : O/P 1 INHIB. --
(II) WIRE HARNESS
K OR A
KEY ALARM
●
●
●
●
●
●
5
14 : INT. LOCK
15 : GND (–) --
16 : DU OUT --
(III) LED INDICATORS
one
MAINS (AMBER)
DOOR (GREEN) (Wire 3-4)
ALARM (RED) (Wire 5-6)
AUXILIARY (RED) (Wire 7)
AUX LED
INHIBIT AUX
●
●
●
●
●
●
●
6
(IV) PACIFIER TONES & THE LED INDICATING SIGNALS
NOTE:
*
**
STATUS TONES*LED SIGNALS
1. In programming mode
---
1 Beep
2 Beeps
5 Beeps
Continuous Beeps
---
1 second Long Beep **
ON
1 Flash
2 Flashes
5 Flashes
Continuous Flashes
1 Flash in 2 seconds interval
---
2. Successful key entry
3. Successful code entry
4. Unsuccessful code entry
5. DAP jumper not replaced
6. In standby mode
7. Output relay activated
7
A) Enter Programming Mode with Master Code (Exit-Factory Master Code: 0 0 0 0)
NOTE:
B) System Refreshing –
C) Code Entries –
1) Recording Master Code and User Codes – (No Default Codes)
2) Recording Super User Code – (No Default Codes)
3) Recording Duress Codes – (No Default Codes)
4) Recording the Visitor Codes – (No Default Codes)
STANDARD PROGRAMMING SUMMARY CHART
8
19
The Duress Output will switch to ( ) ground when duress code is entered. You may use it to turn ON an LED
lamp and /or a small buzzer to notifyaguard; or connect it toa24 hour Normally Open protection zone of an
alarm system.
-
Only one connection option is recommended. Make sure that the sink current does not exceed the maximum
rating of 100mA.
(D) DURESS OUTPUT (WHITE/ORANGE WIRE)
(E) OUTPUT 2
OR
1.5K
LED
+12V
LOW POWER
PIEZO BUZZER
(10)
(11)
(12)
(13)
(14)
(15)
(16) WHITE/ORANGE
WIRE HARNESS
ALARM CONTROL PANEL
24 HOUR N.O.
PROTECTION
ZONE
(10)
(11)
(12)
(13)
(14)
(15) YELLOW GREEN
(16) WHITE/ORANGE
WIRE HARNESS
(i)Shunting an N.C. Zone(WHITE/BROWN&BLUE WIRES)
Use the Normally Open (N.O.) output contact to shuntaNormally Closed (N.C.) protection zone of an
alarm system.
Set output contact to Start/Stop Mode (Programming Option 51).
( ii)Alarm System Arm-Disarm Control(WHITE/BROWN&BLUE or PURPLE WIRES)
Use the (N.O.) or (N.C.) output contact to make arm-disarm control of an alarm system.
Consult your alarm control panel manual for the appropriate output contact to be used in arm-disarm control.
Usually set output 2 to Momentary mode (Programming Option 501) for multi station systems and Start
/ Stop mode (Programming Option 51) for single station systems.
WIRE HARNESS
(8)
(9) WHITE/BROWN
(10) BLUE
(11) PURPLE
(12)
OR
ALARM CONTROL PANEL
REMOTE
ARM-DISARM
CONTROL
NO. OR N.C.
WIRE HARNESS
(8)
(9) WHITE/BROWN
(10) BLUE
(11)
(12)
N.C.
N.C. MAGNETIC CONTACT
TO PROTECTION ZONE
OF AN ALARM CONTROL PANEL
(Default: Momentary, 1-second for all 3 outputs)
(default = 1 second)
(default = 1 second)
(Default: Fail-Secure)
(Default: 10 tries / 30 seconds)
(default)
G) Door Forced-Open Alarm – (Default: Disabled)
(default)
(default=1 second)
9
(Default: 1 long beep)
I) User Code Entry Modes (Auto or Manual) – (Default: Manual)
(Default: ON)
(default)
K) Main LED Flashing ON-OFF – (Default: Flashing)
L) Egress Delay & Warning – (Default: Instant, No warning)
(default)
M) Delay Time to Start Door Propped-up Warning – (Default: OFF)
(default)
N) Exit Programming Mode
(default)
(default)
(default)
10
Criteria for Programming
MUST
DO NOT
Enter and Exit Programming Mode
key.
Master Code
3. Exit the programming mode by pressing the
NOTE:
●
●
●
●
●
SETTING & PROGRAMMING
DAP
ON OFF
11
New Master Code
NOTE:
●
●
●
Programming Example :
0 0 0 0
2. Program a new Master Code 3 2 8 9 for the keypad:
NOTE:
●3 2 8 9
●
3 2 8 9
2. key to clear all the current stored data
except the Master Code:
NOTE:
●(default)
System Refresh (Complete Data Refresh) (Refresh Code 8901)
12
User ID Entry of Code
Output 1
Output 2
Output 3
NOTE:
●
●00-99
●0-9
●
●
●
Programming Example :
code 3 2 8 9
2. Program an User Code 8 3 2 1 for output 1 ---------- One of the 100 user codes (user ID: 00-99,
taking ID = 01 as example):
3. Program an User Code 5 4 3 2 1 for output 2 ------- One of the 10 user codes (user ID: 0-9, taking
ID=1 as example):
4. Program an User Code 9 2 7 0 5 3 for output 3 ---- One of the 10 user codes (user ID: 0-9, taking
ID=1 as example):
Operaon (Manual Code Entry Mode)
NOTE:
13
Super User Code
NOTE:
●
●
●
●
Programming Example :
3 2 8 9
2. Program 2 5 8 0 as Super User Code:
Operaon :
14
NOTE:
●
●
●This feature is recommended for Fail-safe locks only.
●
REMARK :
●
●
●
●
●
●
3)
NOTE:
●
●
●
●
15
User ID Duress Code
NOTE:
●
●0-9
●
●
For example:1 3 5 7
3 3 5 7 1 3 5 8
●
●
Programming Example :
3 2 8 9
2. Program 3 3 5 7 as 1st Duress Code:
Program 2 3 9 8 0 as 2nd Duress Code --- if more user needs duress code:
Operaon :
NOTE :
●
●
16
One-Time
Time-Limit
User ID Entry of Code
NOTE:
●
●0-9
●
●
●
●
Programming Example :
3 2 8 9
2. Program a Visitor Code 1 3 7 8
3. Program a Visitor Code 2 3 0 8 9
4. Program a Visitor Code 8 3 5 8
Operaon :
17
Deleng Examples:
3289
a)
b)
c)
d)
e)
f)
18
Time Length
A)
B)
C)
D)
NOTE:
●
●
●
Programming Options for Outputs 1, 2 & 3 (See “Programming Summary Chart” Secon D for more
informaon) :
Example:
8 3 2 18 3
5 4 3 2 15 4
Example:
5 4 3 2 15 4 3
9 2 7 0 5 39 2 7
19
Operaon :
8 3 2 1
5 4 3 2 1
9 2 7 0 5 3
NOTE:
●The purpose of the accelerated Code --
●
Super User Code
Super User Code
Super User Code
Programming Examples:
3 2 8 9
2. Set Output 1 in momentary mode of 5 seconds:
3. Set Output 2 in Start / Stop Mode:
4. Set Output 3 in Start / Stop Mode with 3-digit Accelerated Start Code:
20
Table of contents
Other APO Keypad manuals
APO
APO DK-9350 User manual
APO
APO DK-9820 MK-II User manual
APO
APO DK-9522 MK-II User manual
APO
APO DK-9330 A User manual
APO
APO DK-9866 MK-II User manual
APO
APO DK-9821 MK-II User manual
APO
APO DK-9520 MK-II User manual
APO
APO DK-9865 MK-II User manual
APO
APO DK-9827 MK-II User manual
APO
APO DK-9826 MK-II User manual
Popular Keypad manuals by other brands
Honeywell
Honeywell 6280W Features & specifications
Russound
Russound SaphIR K2 instruction manual
Niles
Niles NUMERIC-6P Features & specifications
Carefree
Carefree 1050A-2 owner's manual
Third Millennium
Third Millennium TMM60/A01 Series installation instructions
Dormakaba
Dormakaba LA GARD 700 Series installation guide
