APO DK-9330 A User manual
VANDAL RESISTANT
DIGITAL ACCESS CONTROL KEYPAD
DK-9330 A&B
Programming & Installation Manual
FOR ELECTRIC LOCK
AND SECURITY SYSTEM INSTALLATIONS
TABLE OF CONTENTS
INTRODUCTION
DESCRIPTION OF CONNECTION TERMINALS & INDICATORS
STANDARD PROGRAMMING SUMMARY CHART
SETTING & PROGRAMMING
SET KEYPAD TO SINGLE USER MODE (to whom it may require)
SPECIFICATIONS
APPLICATION EXAMPLE
APPLICATION HINTS FOR THE AUXILIARY FACILITIES
AUXILIARY INFORMATION
······························································································································· 3
······················································ 3-7
················································································································· 4-5
························································································································· 6
··········································································· 6
·········································································· 7-9
······································································································ 10-26
············································································································· 10
····························································································· 10
············· 10
······························································································ 11
··················································································· 11
······································································································· 12
························································································ 13-14
·································································································· 15
··································································································· 16
·············································································· 17
····························································· 18-19
················································································ 20
··························································································· 21
······································································································ 21
··················································································· 22
·················································································································· 22
································································································ 22
·········································································································· 23-24
·········································································· 24
············································· 25-26
································································ 25
·········································································· 26
······························································································································ 27
············································································································ 28-29
······························································ 30-32
············································································································· 33
2
INTRODUCTION
DESCRIPTION OF CONNECTION TERMINALS & INDICATORS
DK-9330A --
DK-9330B --
RED (OUTPUT 2)
AMBER (MAINS)
GREEN / RED
(DOOR /
Standard Version
Bell Button Version
MOUNTING
SCREW HOLES
CONNECTION
WIRE IN/OUT
SLOTS
3
1 - 2 : TAMPER N.C.
3 - 4 : 12-24V AC/DC --
5 - 6 - 7 : OUTPUT 1
N.O. contact for Fail-secureN.C. contact for Fail-safe
8 - 9 : OUTPUT 2
a) Standard Version
●
●
●
●
CONNECTION TERMINALS
N.C. N.O.
OUTPUT 2
OUTPUT 2 SELECTION JUMPER
N.C. -- Normally Closed
N.O. -- Normally Open
Back-Lit Jumper
DAP Jumper
4
10 : ALM OUT --
11 : DU OUT --
12 - EG IN --
13 : GND (–) --
14 : DOOR SENS --
NOTE:
1) Door Auto Re-lock
2) Door Forced Open Alarm and Warning
3) Door Propped-up Warning
●
●
●
●
●
5
THE LED INDICATORS
MAINS (AMBER)
DOOR / INHIBIT (GREEN / RED)
OUTPUT 2 (RED)
BACK LIGHTING (BACK-LIT JUMPER SELECTION)
●
●
●
THE PACIFIER TONES & THE LED INDICATING SIGNALS
NOTE:
*
**
STATUS TONES*LED SIGNALS
1. In programming mode
---
1 Beep
2 Beeps
5 Beeps
Continuous Beeps
---
1 second Long Beep **
ON
1 Flash
2 Flashes
5 Flashes
Continuous Flashes
1 Flash in 2 seconds interval
---
2. Successful key entry
3. Successful code entry
4. Unsuccessful code entry
5. DAP jumper not replaced
6. In standby mode
7. Output relay activated
AUTO FULL
BACK-LIT
6
A) Enter Programming Mode with Master Code (Exit-Factory Master Code: 0 0 0 0)
NOTE:
B) System Refreshing –
C) Code Entries –
1) Recording Master Code and User Codes – (No Default Codes)
2) Recording Super User Code – (No Default Codes)
3) Recording Duress Codes – (No Default Codes)
4) Recording the Visitor Codes – (No Default Codes)
STANDARD PROGRAMMING SUMMARY CHART
7
(Default: Momentary, 1-second for all 3 outputs)
(default = 1 second)
(Default: 10 tries / 30 seconds)
(default)
F) Door Forced-Open Alarm – (Default: Disabled)
(default)
(Default: 1 long beep)
(default=1 second)
(default)
8
H) User Code Entry Modes (Auto or Manual) – (Default: Manual)
(Default: ON)
(default)
J) Main LED Flashing ON-OFF – (Default: Flashing)
K) Egress Delay & Warning – (Default: Instant, No warning)
(default)
L) Delay Time to Start Door Propped-up Warning – (Default: OFF)
(default)
M) Exit Programming Mode
(default)
(default)
9
Criteria for Programming
MUST
DO NOT
Enter and Exit Programming Mode
key.
Master Code
3. Exit the programming mode by pressing the
NOTE:
●
●
●
●
●
SETTING & PROGRAMMING
DAP
ON OFF
10
New Master Code
NOTE:
●
●
●
Programming Example :
0 0 0 0
2. Program a new Master Code 3 2 8 9 for the keypad:
NOTE:
●3 2 8 9
●
3 2 8 9
2. key to clear all the current stored data
except the Master Code:
NOTE:
●(default)
System Refresh (Complete Data Refresh) (Refresh Code 8901)
11
User ID Entry of Code
Output 1
Output 2
NOTE:
●
●00-99
●0-9
●
●
●
Programming Example :
3 2 8 9
2. Program an User Code 8 3 2 1 for output 1 ---------- One of the 100 user codes (user ID: 00-99,
taking ID = 01 as example):
3. Program an User Code 5 4 3 2 1 for output 2 ------- One of the 10 user codes (user ID: 0-9, taking
ID=1 as example):
Operaon (Manual Code Entry Mode)
NOTE:
12
Super User Code
NOTE:
●
●
●
●
Programming Example :
3 2 8 9
2. Program 2 5 8 0 as Super User Code:
Operaon :
13
NOTE:
●
●
●This feature is recommended for Fail-safe locks only.
●
REMARK :
●
●
●
●
●
●
3)
NOTE:
●
●
●
●
14
User ID Duress Code
NOTE:
●
●0-9
●
●
For example:1 3 5 7
3 3 5 7 1 3 5 8
●
●
Programming Example :
3 2 8 9
2. Program 3 3 5 7 as 1st Duress Code:
Program 2 3 9 8 0 as 2nd Duress Code --- if more user needs duress code:
Operaon :
NOTE :
●
●
15
16
One-Time
Time-Limit
User ID Entry of Code
NOTE:
●
●0-9
●
●
●
●
Programming Example :
3 2 8 9
2. Program a Visitor Code 1 3 7 8 at ID “0” for One-Time use:
3. Program a Visitor Code 2 3 0 8 9 at ID “1” with Time-Limit of 5 hours:
4. Program a Visitor Code 8 3 5 8 at ID “2” with Time-Limit of 10 hours:
Operaon :
Deleng Examples:
3289
a)
b)
c)
d)
e)
17
Time Length
A)
B)
C)
D)
NOTE:
●
●
Programming Options for Outputs 1 & 2 (See “Programming Summary Chart” Secon D for more
informaon) :
or 51 : Start / Stop Mode (toggle)
or 52 : Start / Stop Mode (toggle) with 2-digit Accelerated Code
Example:
8 3 2 18 3
5 4 3 2 15 4
Example:
5 4 3 2 15 4 3
9 2 7 0 5 39 2 7
18
Operaon :
8 3 2 1
5 4 3 2 1
5 4 3 2 1
NOTE:
●The purpose of the accelerated Code --
●
Super User Code
Super User Code
Programming Examples:
3 2 8 9
2. Set Output 1 in momentary mode of 5 seconds:
3. Set Output 2 in Start / Stop Mode; OR
4. Set Output 2 in Start / Stop Mode with 3-digit Accelerated Start Code:
19
Programming Codes for Lock-Up Opons:
Super User Code
Super User Code
Programming Examples:
3 2 8 9
(Default)
20
This manual suits for next models
1
Table of contents
Other APO Keypad manuals
APO
APO DK-9522 MK-II User manual
APO
APO DK-9826 MK-II User manual
APO
APO DK-9827 MK-II User manual
APO
APO DK-9823 MK-II User manual
APO
APO DK-9866 MK-II User manual
APO
APO DK-9865 MK-II User manual
APO
APO DK-9820 MK-II User manual
APO
APO DK-9520 MK-II User manual
APO
APO DK-9821 MK-II User manual
APO
APO DK-9350 User manual
