APO DK-9522 MK-II User manual
MULTI-PURPOSE
DIGITAL ACCESS CONTROL KEYPAD
DK-9522 MK-II
Programming & Installation Manual
FOR ELECTRIC LOCK, INTER-LOCK
AND SECURITY SYSTEM INSTALLATIONS
TABLE OF CONTENTS
INTRODUCTION
DESCRIPTION OF CONNECTION TERMINALS & INDICATORS
STANDARD PROGRAMMING SUMMARY CHART
SETTING & PROGRAMMING
SET KEYPAD TO SINGLE USER MODE (to whom it may require)
SPECIFICATIONS
APPLICATION EXAMPLE
APPLICATION HINTS FOR THE AUXILIARY FACILITIES
AUXILIARY INFORMATION
······························································································································· 3
······················································ 3-7
················································································································· 4-5
························································································································· 6
··········································································· 6
·········································································· 7-9
······································································································ 10-26
············································································································· 10
····························································································· 10
············· 10
······························································································ 11
··················································································· 11
······································································································· 12
························································································ 13-14
·································································································· 15
··································································································· 16
·············································································· 17
····························································· 18-19
·················································································· 20
················································································ 21
··························································································· 22
······································································································ 22
··················································································· 23
·················································································································· 23
································································································ 23
·········································································································· 24-25
·········································································· 25
············································· 26-27
································································ 26
·········································································· 27
······························································································································ 28
············································································································ 29-31
······························································ 32-33
············································································································· 34
2
INTRODUCTION
DESCRIPTION OF CONNECTION TERMINALS & INDICATORS
Output 1 Output 2
3 Amp Solid State 1 Amp Relay
DK-9521/DK-9522 is an universal, self-contained digital access keypad oers eld proven reliability and cost
eective solutions for residential and commercial installations. It is designed for stand alone electric lock and inter-
lock systems and operates froma12 to 24V AC/DC power supply and virtually compatible with any electric locking
device. Apart from that it is also the perfect choice for controlling security systems, automatic operators and
machinery. The DK-9521 oers single relay output, and that the DK-9522 oers dual relay output.
DK-9521/DK-9522 consists two application softwares of Single User Mode for the general Users, and Multi-User
Mode for the advanced Users. The system oersa4digit length user code with 10,000 combinations for each
output in single user mode; and 100 user codes for output 1 and 10 user codes for output2in length of 4-8 digits
with combinations of more than 100 million in multi-user mode. Operation options of Auto Code entry and Manual
Code entry are available in both two user modes. Programmed information that stored in the system are non-volatile
Normally Closed contact while the keypad is secured on the box. It is open while keypad is separated from the
box. Connect this N.C. terminal to the 24 hour zone of an alarm system if necessary.
Connect to 12-24V AC or DC power supply. The ( ) supply and ( ) GND are the common grounding points of
the keypad system. No selection jumper is required for the full input voltage range.
Connect DC power with the (+) and ( ) polarity indicated; and there is no polarity discrimination for AC power
12 24V AC/DC (POWER INPUT)
- -
CONNECTION TERMINALS
OUTPUT OUTPUT 1
5 Amp relay
5 Amp relay
OUTPUT 2
NPN Open Collector
1 Amp relay
RELAY
1RELAY
2
ON OFF
DAP
+-
12 24V
TAMPER
N.C.
EG
IN
OUTPUT 1
N.C. C. N.O.
TUPTUO 2
.O.N.C.C.N
YEK
.TCA
ROOD
SNES
)(
DNG
-UD
TUO
.TNI
KCOL
1P/O
BIHNI
TAMP
ON OFF
DAP
EG
IN
OUTPUT 1
N.C. C. N.O.
TUPTUO 2
.O.N.C.C.N
YEK
.TCA
ROOD
SNES
)(
DNG
-UD
TUO
.TNI
KCOL
1P/O
BIHNI
DK-9521 DK-9522
R
1 2 3
456
78 9
0#
RED
AMBER
GREEN
DK-9521
3
5 Amp relay dry contacts, recommended for door strike controls. Normally Open (N.O.) and Normally Closed
(N.C.) outputs are available. Use N.O. output for Fail-secure locking device and N.C. output for Fail-safe locking
device. The relay can be programmed in Start/Stop (toggle) mode or timer mode from1to 999 seconds.
2
1 - 2 : TAMPER N.C.
3 - 4 : 12V DC --
6 - 7 : OUTPUT 1 --
Fail-Secure Electric
Lock in Default
8 - EG IN --
9 - 10 - 11 : OUTPUT 2
I
12 : KEY ACT --
13 : DU OUT --
14 : GND (-) --
●
●
●
●
●
●
●
●
CONNECTION TERMINALS
4
15 : DOOR SENS --
NOTE:
1) Door Auto Re-lock
2) Door Forced Open Warning
3) Door Propped-up Warning
4) Inter-lock Control
16 : O/P 1 INHIB. --
17 : INT. LOCK
●
●
●
5
THE LED INDICATORS
MAINS (AMBER)
dŚŝƐŝƐĂƐƚĂƚƵƐŝŶĚŝĐĂƚŽƌ/ƚŇĂƐŚĞƐĚƵƌŝŶŐƐƚĂŶĚďLJĂŶĚŽƚŚĞƌŝŶĚŝĐĂƟŽŶƐŝŶƐLJŶĐŚƌŽŶŝnjĂƟŽŶǁŝƚŚ
ƚŚĞƉĂĐŝĮĞƌƚŽŶĞƐ^ĞĞƚŚĞĐŚĂƌƚŽĨ>ŝŶĚŝĐĂƟŽŶƐŝŐŶĂůƐďĞůŽǁĨŽƌƚŚĞĚĞƚĂŝůƐ
DOOR / INHIBIT (GREEN / RED)
dŚŝƐŝƐĂĚƵĂů>ĂƚƚŚĞƌŝŐŚƚƐŝĚĞŽĨƚŚĞƉĂŶĞů/ƚůŝŐŚƚƐƵƉŝŶŐƌĞĞŶǁŚŝůĞŽƵƚƉƵƚϭŝƐĂĐƟǀĞ;dŚĞ
ĚŽŽƌŝƐŽƉĞŶͿĂŶĚƌĞĚǁŚŝůĞKƵƚƉƵƚϭŝƐ/ŶŚŝďŝƚĞĚŝŶĐůƵĚŝŶŐŵĂŶƵĂůůLJŝŶŚŝďŝƚĞĚǁŝƚŚ^ƵƉĞƌhƐĞƌ
ŽĚĞŽƌĚƵĞƚŽ&ĂůƐĞŽĚĞ>ŽĐŬͲƵƉƐĞƫŶŐŝŶ>ŽĐĂƟŽŶϳϬ
OUTPUT 2 (GREEN)
/ƚůŝŐŚƚƐƵƉǁŚŝůĞŽƵƚƉƵƚϮŝƐĂĐƟǀĞ
BACK LIGHTING (Back-lit Version Keypad Only)
dŚĞŬĞLJƉĂĚŝƐŝŶĚŝŵďĂĐŬůŝŐŚƟŶŐĚƵƌŝŶŐƚŚĞƐƚĂŶĚďLJƉĞƌŝŽĚ/ƚŐĞƚƐďƌŝŐŚƚĞƌĨŽƌϭϬƐĞĐŽŶĚƐŽŶĞĂĐŚ
ŬĞLJďƵƩŽŶƉƌĞƐƐǁŚŝĐŚŝŶĚŝĐĂƚĞƐƚŚĞĂůůŽǁĂďůĞƟŵĞĨŽƌƐƵĐĐĞĞĚŝŶŐĐŽĚĞĞŶƚƌLJdŚĞƉƌĞǀŝŽƵƐĐŽĚĞƐ
ǁŝůůďĞĐĂŶĐĞůůĞĚŝĨŶŽĐŽĚĞŝƐĞŶƚĞƌĞĚǁŝƚŚŝŶϭϬƐĞĐŽŶĚƐ
THE PACIFIER TONES & THE LED INDICATING SIGNALS
dŚĞďƵŝůƚͲŝŶďƵnjnjĞƌĂŶĚƚŚĞD/E^>ŝŶĚŝĐĂƚŽƌŐŝǀĞƚŚĞĨŽůůŽǁŝŶŐƚŽŶĞƐĂŶĚƐŝŐŶĂůƐĨŽƌŽƉĞƌĂƟŽŶ
ƐƚĂƚƵƐ
NOTE:
ůůWĂĐŝĮĞƌdŽŶĞƐĐĂŶďĞĞŶĂďůĞĚŽƌĚŝƐĂďůĞĚƚŚƌŽƵŐŚƉƌŽŐƌĂŵŵŝŶŐŽƉƟŽŶƐĂƚ>ŽĐĂƟŽŶϴϯ
**
dŚĞKƵƚƉƵƚĐƟǀĂƟŽŶĞĞƉĐĂŶďĞĞŶĂďůĞĚŽƌĚŝƐĂďůĞĚƚŚƌŽƵŐŚƉƌŽŐƌĂŵŵŝŶŐŽƉƟŽŶƐĂƚ>ŽĐĂƟŽŶϴϭ
STATUS TONES*LED SIGNALS
1. In programming mode
---
1 Beep
2 Beeps
5 Beeps
Continuous Beeps
---
1 second Long Beep **
ON
1 Flash
2 Flashes
5 Flashes
Continuous Flashes
1 Flash in 2 seconds interval
---
2. Successful key entry
3. Successful code entry
4. Unsuccessful code entry
5. DAP jumper not replaced
6. In standby mode
7. Output relay activated
3) BASIC WIRINGS OF AN INTER-LOCK SYSTEM USING TWO KEYPADS
ŶŝŶƚĞƌͲůŽĐŬƐLJƐƚĞŵŶĞĞĚƐƚǁŽĚŽŽƌĐŽŶƚƌŽůůĞƌƐdŚŝƐĂƉƉůŝĐĂƚŝŽŶĞdžĂŵƉůĞƵƐĞƐƚǁŽŬĞLJƉĂĚƐǁŝƚŚ
ƐŝŵƉůĞ ĐƌŽƐƐ ǁŝƌĞ ĐŽŶŶĞĐƚŝŽŶ ŽŶ ƚŚĞŝƌ "Output 1 INHIBIT" ĂŶĚ "Inter-lock Control Output"
ƚĞƌŵŝŶĂůƐ/ƚŝƐŶĞĐĞƐƐĂƌLJƚŽůŝŶŬƵƉƚŚĞ"(–) GND"ƚĞƌŵŝŶĂůƐŽĨƚŚĞƚǁŽŬĞLJƉĂĚƐĂƐĐŽŵŵŽŶŐƌŽƵŶĚ
ƚŽĂĐŚŝĞǀĞƚŚĞŝŶƚĞƌͲůŽĐŬůŽŐŝĐĂůĨƵŶĐƚŝŽŶƐ
ƔhƐĞŬĞLJƉĂĚƚŽŽƉĞŶƚŚĞĚŽŽƌĨƌŽŵŽƵƚƐŝĚĞ
ƔWƌĞƐƐĞŐƌĞƐƐďƵƚƚŽŶƚŽŽƉĞŶƚŚĞĚŽŽƌĨƌŽŵŝŶƐŝĚĞ
ƔŽŶŶĞĐƚƚŚĞĚŽŽƌŵĂŐŶĞƚŝĐƐĞŶƐŽƌƐŽŶƚŚĞĚŽŽƌϭĂŶĚĚŽŽƌϮƚŽŵŽŶŝƚŽƌƚŚĞŝƌƉŽƐŝƚŝŽŶƐ
ƔƵƌŝŶŐƚŚĞƚŝŵĞƚŚĂƚĚŽŽƌϭŝƐŽƉĞŶƚŚĞŶĚŽŽƌϮŝƐĨŽƌĐĞĚƚŽŬĞĞƉĐůŽƐĞĚŽƌǀŝĐĞǀĞƌƐĂ
Ɣ^ĞĞƉƌŽŐƌĂŵŵŝŶŐ>ŽĐĂƟŽŶϲϲĨŽƌ&ĂŝůͲƐĞĐƵƌĞŽƌ&ĂŝůͲƐĂĨĞĞůĞĐƚƌŝĐůŽĐŬƐĞƫŶŐ
ƔZĞůĂLJŽƵƚƉƵƚϮŝƐŝŶĚĞƉĞŶĚĞŶƚĂŶĚŚĂƐŶŽƚŚŝŶŐĐŽŶĐĞƌŶǁŝƚŚƚŚĞŝŶƚĞƌͲůŽĐŬƐLJƐƚĞŵ/ƚŵĂLJďĞƵƐĞĚ
ĨŽƌŽƚŚĞƌĂƉƉůŝĐĂƚŝŽŶƐƐƵĐŚĂƐĐŽŶƚƌŽůůŝŶŐƐĞĐƵƌŝƚLJƐLJƐƚĞŵƐĂƵƚŽŵĂƚŝĐŽƉĞƌĂƚŽƌƐĞƚĐ
ƔWůĞĂƐĞĂůƐŽƐĞĞƚŚĞΗEKdΗƐƚĂƚĞĚŝŶƚŚĞƉƉůŝĐĂƚŝŽŶ;ϭͿĂŶĚ;ϮͿĨŽƌƚŚĞĐŽŵŵŽŶŝŶĨŽƌŵĂƚŝŽŶ
Ɣ
Ɣ
Ɣ
DOOR1
DOOR 2
SENSING
N.C.
DOOR2
COMMON GROUND
ELECTRIC LOCK
12V DC
POWER
SUPPLY
1N4004
N.O.
EG
IN
TAMPER
N.C.
(+) (–)
12 VDC
(+) (–)
DOOR LOCK
ϭ Ϯ ϯ ϰ ϱ ϲ ϳ ϴ
ELECTRIC LOCK
12V DC
POWER
SUPPLY
1N4004
N.O.
EG
IN
TAMPER
N.C.
(+) (–)
12 VDC
(+) (–)
DOOR LOCK
ϭ Ϯ ϯ ϰ ϱ ϲ ϳ ϴ
OUTPUT 2
N.C. COM. N.O.
( – )
GND
DOOR
SENS
O/P 1
INHIB
DU
OUT
INT.
LOCK
KEY
ACT.
ϵ ϭϬ ϭϭ ϭϮ ϭϯ ϭϰ ϭϱ ϭϲ ϭϳ
OUTPUT 2
N.C. COM. N.O.
( – )
GND
DOOR
SENS
O/P 1
INHIB
DU
OUT
INT.
LOCK
KEY
ACT.
ϵ ϭϬ ϭϭ ϭϮ ϭϯ ϭϰ ϭϱ ϭϲ ϭϳ
DOOR 1
SENSING
N.C.
CROSS WIRE CONNECTION FOR INTER-LOCK FUNCTIONS
CROSS WIRE CONNECTION FOR INTER-LOCK FUNCTIONS
EGRESS
BUTTON
(OPEN DOOR 1
FROM INSIDE)
EGRESS
BUTTON
(OPEN DOOR 2
FROM INSIDE)
6 31
A) Enter Programming Mode with Master Code (Exit-Factory Master Code: 0 0 0 0)
NOTE:
B) System Refreshing –
C) Code Entries –
1) Recording Master Code and User Codes – (No Default Codes)
2) Recording Super User Code – (No Default Codes)
3) Recording Duress Codes – (No Default Codes)
4) Recording the Visitor Codes – (No Default Codes)
STANDARD PROGRAMMING SUMMARY CHART
7
(Default: Momentary, 1-second for all 3 outputs)
(default = 1 second)
(Default: Fail-Secure)
(Default: 10 tries / 30 seconds)
(default)
G) Door Forced-Open Warning – (Default: Disabled)
(default)
(Default: 1 long beep)
(default=1 second)
(default)
8
( ii)Alarm System Arm-Disarm Control
Use the (N.O.) or (N.C.) output contact to make arm-disarm control of an alarm system.
(i)Shunting an N.C. Zone
Use the Normally Open (N.O.) output contact to shunt a Normally Closed (N.C.) protection zone of an
alarm system.
Set output contact to Start / Stop Mode (Programming Option 51).
(E) OUTPUT 2 (FOR DK-9522 ONLY)
ALARM CONTROL PANEL
24 HOUR N.O.
PROTECTION
ZONE
OR
1.5K
LED
+12V
LOW POWER
PIEZO BUZZER
YEK
.TCA
ROOD
SNES
)(
DNG
-UD
TUO
.TNI
KCOL
1P/O
BIHNI
YEK
.TCA
ROOD
SNES
)(
DNG
-UD
TUO
.TNI
KCOL
1P/O
BIHNI
TUPTUO 2
.O.N.C.C.N
YEK
.TCA
N.C.
N.C. MAGNETIC CONTACT
TO PROTECTION ZONE
OF AN ALARM CONTROL PANEL
OR
TUPTUO 2
.O.N.C.C.N
YEK
.TCA
ALARM CONTROL PANEL
REMOTE
ARM-DISARM
CONTROL
NO. OR N.C.
I) User Code Entry Modes (Auto or Manual) – (Default: Manual)
(Default: ON)
(default)
K) Main LED Flashing ON-OFF – (Default: Flashing)
L) Egress Delay & Warning – (Default: Instant, No warning)
(default)
M) Delay Time to Start Door Propped-up Warning – (Default: OFF)
(default)
N) Exit Programming Mode
(default)
(default)
9
Usually set output 2 to Momentary mode (Programming Option 501) for multi station systems and Start
/ Stop mode (Programming Option 51) for single station systems.
19
Criteria for Programming
MUST
DO NOT
Enter and Exit Programming Mode
key.
Master Code
3. Exit the programming mode by pressing the
NOTE:
●
●
●
●
●
SETTING & PROGRAMMING
DAP
ON OFF
10
New Master Code
NOTE:
●
●
●
Programming Example :
0 0 0 0
2. Program a new Master Code 3 2 8 9 for the keypad:
NOTE:
●3 2 8 9
●
3 2 8 9
2. key to clear all the current stored data
except the Master Code:
NOTE:
●(default)
System Refresh (Complete Data Refresh) (Refresh Code 8901)
11
User ID Entry of Code
Output 1
Output 2
NOTE:
●
●00-99
●0-9
●
●
●
Programming Example :
3 2 8 9
2. Program an User Code 8 3 2 1 for output 1 ---------- One of the 100 user codes (user ID: 00-99,
taking ID = 01 as example):
3. Program an User Code 5 4 3 2 1 for output 2 ------- One of the 10 user codes (user ID: 0-9, taking
ID=1 as example):
Operaon (Manual Code Entry Mode)
NOTE:
12
Super User Code
NOTE:
●
●
●
●
Programming Example :
3 2 8 9
2. Program 2 5 8 0 as Super User Code:
Operaon :
13
NOTE:
●
●
●This feature is recommended for Fail-safe locks only.
●
REMARK :
●
●
●
●
●
●
3)
NOTE:
●
●
●
●
14
ƵƌĞƐƐŽĚĞ;ƐͿŝƐĂŶŝŵƉŽƌƚĂŶƚĐŽĚĞƚŽƉƌŽƚĞĐƚƚŚĞƵƐĞƌŝŶĐĂƐĞŽĨĨŽƌĐŝŶŐƚŽŽƉĞŶƚŚĞĚŽŽƌƵŶĚĞƌ
ĚƵƌĞƐƐdŚĞĚƵƌĞƐƐĐŽĚĞŽƉĞƌĂƚĞƐůŝŬĞĂŶŽƌŵĂůƵƐĞƌĐŽĚĞƚŽĂĐƟǀĂƚĞKƵƚƉƵƚϭĨŽƌĚŽŽƌŽƉĞŶŝŶŐĂŶĚ
ĂƚƚŚĞƐĂŵĞƟŵĞŝƚĂůƐŽĂĐƟǀĂƚĞƐƚŚĞƵƌĞƐƐKƵƚƉƵƚǁŝƚŚŽƵƚĂŶLJŝŶĚŝĐĂƟŽŶdŚĞĚƵƌĞƐƐŽƵƚƉƵƚĐĂŶ
ďĞƵƐĞĚƚŽĂĐƚƵĂƚĞƵƚŽͲĚŝĂůĞƌŽƌƐĞĐƵƌŝƚLJƐLJƐƚĞŵƚŽƌĞƉŽƌƚƚŚĞĞǀĞŶƚ
>ŽĐĂƟŽŶƐ User ID Duress Code ŽŶĮƌŵ
ϬͲϵϰͲϴŝŐŝƚƐ
NOTE:
ƔƵƌĞƐƐĐŽĚĞƐĐĂŶďĞϰͲϴĚŝŐŝƚƐůŽŶŐŝŶŵĂŶƵĂůĐŽĚĞĞŶƚƌLJŵŽĚĞďƵƚŵƵƐƚŚĂǀĞƚŚĞƐĂŵĞůĞŶŐƚŚĂƐ
ƚŚĞŵĂƐƚĞƌĐŽĚĞŝĨƚŚĞŬĞLJƉĂĚŝƐŝŶĂƵƚŽĐŽĚĞĞŶƚƌLJŵŽĚĞ
ƔϭϬƵŶŝƋƵĞhƐĞƌ/Ɛ0-9ĨŽƌϭϬƵƌĞƐƐŽĚĞƐ
ƔdŚĞƵƌĞƐƐĐŽĚĞ ĐŽŶƟŶƵĞƐƚŽŽƉĞƌĂƚĞĂŶĚŝƐ ŶŽƚŐŽǀĞƌŶĞĚďLJĂŶLJƐLJƐƚĞŵŝŶŚŝďŝƟŶŐŽƌůŽĐŬͲƵƉ
ĨƵŶĐƟŽŶ
ƔůǁĂLJƐƐĞƚĂƵƌĞƐƐĐŽĚĞƚŚĂƚŝƐĞĂƐLJƚŽƌĞŵĞŵďĞƌŝŶWĂŶŝĐƐŝƚƵĂƟŽŶKŶůLJŽŶĞŶƵŵďĞƌĚŝīĞƌĞŶƚ
ĨƌŽŵƚŚĞĚĂŝůLJƵƐĞĚhƐĞƌĐŽĚĞŝƐƌĞĐŽŵŵĞŶĚĞĚFor example:ĂŝůLJhƐĞƌŽĚĞŝƐ1 3 5 7ƚŚĞŶ
3 3 5 7 Žƌ1 3 5 8ŵĂLJďĞĂŐŽŽĚĐŚŽŝĐĞĨŽƌƵƌĞƐƐĐŽĚĞ
Ɣ^ĞĞWƌŽŐƌĂŵŵŝŶŐ^ƵŵŵĂƌLJŚĂƌƚ^ĞĐƟŽŶʹϯĨŽƌŵŽƌĞŝŶĨŽƌŵĂƟŽŶ
Ɣ^ĞĞŝŶĨŽƌŵĂƟŽŶŽŶ>ŽĐĂƟŽŶϴϮĐŽŶĐĞƌŶŝŶŐĚŝŐŝƚůĞŶŐƚŚŝŶƵƚŽĂŶĚDĂŶƵĂůĐŽĚĞĞŶƚƌLJŵŽĚĞƐ
Programming Example :
ϭ^ĞƚŬĞLJƉĂĚƚŽƉƌŽŐƌĂŵŵŝŶŐŵŽĚĞǁŝƚŚŵĂƐƚĞƌĐŽĚĞĂŶĚ ŬĞLJdĂŬŝŶŐƚŚĞƉƌĞǀŝŽƵƐƉƌŽŐƌĂŵŵĞĚ
ŵĂƐƚĞƌĐŽĚĞ3 2 8 9ĂƐĞdžĂŵƉůĞŚĞƌĞ
2. Program 3 3 5 7 as 1st Duress Code:
Program 2 3 9 8 0 as 2nd Duress Code --- if more user needs duress code:
ϯdžŝƚƉƌŽŐƌĂŵŵŝŶŐŵŽĚĞďLJƉƌĞƐƐŝŶŐƚŚĞ
KƉĞƌĂƟŽŶ
ϭĐƟǀĂƚĞKƵƚƉƵƚϭΘƵƌĞƐƐKƵƚƉƵƚǁŝƚŚƚŚĞϰͲĚŝŐŝƚhƐĞƌŽĚĞ
ϮĐƟǀĂƚĞKƵƚƉƵƚϭΘƵƌĞƐƐKƵƚƉƵƚǁŝƚŚƚŚĞϱͲĚŝŐŝƚhƐĞƌŽĚĞ
ϯ ĞͲĂĐƟǀĂƚĞ ;ƌĞƐĞƚͿ ƵƌĞƐƐ KƵƚƉƵƚ ǁŝƚŚ ŶLJ ŶŽƌŵĂů hƐĞƌ ŽĚĞ ϭϯϱϳ ŝƐ ƚŚĞ ƵƐĞƌ ĐŽĚĞ ŝŶ ƚŚŝƐ
ĞdžĂŵƉůĞ
NOTE :
ƔƵƌĞƐƐKƵƚƉƵƚǁŽƌŬƐĐŽŶƟŶƵŽƵƐůLJĂŌĞƌĂĐƟǀĂƚĞĚƵŶƟůƌĞƐĞƚ
ƔƵƌĞƐƐŽĚĞĂůǁĂLJƐĂĐƟǀĂƚĞƐƚŚĞKƵƚƉƵƚϭĂŶĚ ƚŚĞƵƌĞƐƐKƵƚƉƵƚƐŝŵƵůƚĂŶĞŽƵƐůLJďƵƚĐĂŶŶŽƚ
ĚĞͲĂĐƟǀĂƚĞƵƌĞƐƐKƵƚƉƵƚKŶůLJĂŶŽƌŵĂůhƐĞƌŽĚĞŽƌ^ƵƉĞƌhƐĞƌŽĚĞĐĂŶƌĞƐĞƚƵƌĞƐƐKƵƚƉƵƚ
WƌŽŐƌĂŵŵŝŶŐdŚĞƵƌĞƐƐŽĚĞƐ;>ŽĐĂƟŽŶϰϲͿ
KƵƚƉƵƚĐƟǀĂƟŽŶŶŶŽƵŶĐĞƌ;>ŽĐĂƟŽŶϴϭͿ
dŚĞŬĞLJƉĂĚǁŝůůŐŝǀĞĚŽŽƌĨŽƌĐĞĚͲŽƉĞŶǁĂƌŶŝŶŐŝĨƚŚĞĚŽŽƌŝƐŽƉĞŶĞĚǁŝƚŚŽƵƚƵƐŝŶŐĂƵƐĞƌĐŽĚĞŽƌ
ƉƌĞƐƐŝŶŐƚŚĞĞŐƌĞƐƐďƵƩŽŶdŚŝƐĨƵŶĐƟŽŶƌĞƋƵŝƌĞƐĂŶŽƉƟŽŶĂůEŽƌŵĂůůLJůŽƐĞĚ;EͿĚŽŽƌƉŽƐŝƟŽŶ
ŵŽŶŝƚŽƌŝŶŐƐǁŝƚĐŚŽŶƚŚĞĚŽŽƌ;ƵƐƵĂůůLJĂŵĂŐŶĞƟĐĐŽŶƚĂĐƚŽƌŽƚŚĞƌĚŽŽƌƉƌŽƚĞĐƟŽŶƐǁŝƚĐŚǁŝƚŚE
ĐŽŶƚĂĐƚͿKŶĐĞƚŚĞĨƵŶĐƟŽŶŝƐƚƌŝŐŐĞƌĞĚƚŚĞŬĞLJƉĂĚǁŝůůŐŝǀĞǁĂƌŶŝŶŐďĞĞƉƐ
>ŽĐĂƟŽŶƐ &ƵŶĐƟŽŶKƉƟŽŶƐ ŽŶĮƌŵ
ϬŽƌϭ
WƌŽŐƌĂŵŵŝŶŐKƉƟŽŶƐ
ͲͲŽŽƌ&ŽƌĐĞĚͲŽƉĞŶtĂƌŶŝŶŐΘůĂƌŵK&&(Default)
ͲͲdŚĞǁĂƌŶŝŶŐďĞĞƉĂĐƟǀĂƚĞƐĨŽƌϲϬƐĞĐŽŶĚƐ/ƚĐĂŶďĞƌĞƐĞƚǁŝƚŚĂƵƐĞƌĐŽĚĞĨŽƌŽƵƚƉƵƚϭ
NOTE:
ƔdŚĞĚŽŽƌŝƐĨŽƌĐĞĚƚŽŽƉĞŶǁŝƚŚŽƵƚƵƐĞƌĐŽĚĞŽƌƉƌĞƐƐŝŶŐĞŐƌĞƐƐďƵƩŽŶʹtĂƌŶŝŶŐĂĐƟǀĞ
ƔdŚĞĚŽŽƌŝƐŽƉĞŶĞĚǁŝƚŚƵƐĞƌĐŽĚĞŽƌƉƌĞƐƐŝŶŐĞŐƌĞƐƐďƵƩŽŶʹNo Warning
dŚĞƉƵƌƉŽƐĞŽĨŽƵƚƉƵƚĂĐƟǀĂƟŽŶĂŶŶŽƵŶĐĞƌŝƐƚŽŐŝǀĞĂƐŽƵŶĚƐŝŐŶĂůƚŽŶŽƟĨLJƚŚĞǀŝƐŝƚŽƌŽƵƚƐŝĚĞƚŽ
ŽƉĞŶƚŚĞĚŽŽƌǁŚĞŶƚŚĞůŽĐŬŝƐĂĐƟǀĂƚĞĚ/ƚŝƐŐŽŽĚĨŽƌƚŚĞůŽĐŬŝŶŐĚĞǀŝĐĞƐƵĐŚĂƐĂŵĂŐŶĞƟĐůŽĐŬ
ƚŚĂƚŐŝǀĞƐŶŽƐŽƵŶĚǁŚĞŶŝƚŝƐĂĐƟǀĂƚĞĚ
>ŽĐĂƟŽŶƐ &ƵŶĐƟŽŶKƉƟŽŶƐ ŽŶĮƌŵ
ϬϭŽƌϮ
WƌŽŐƌĂŵŵŝŶŐKƉƟŽŶƐ
ͲͲEŽŽƵƚƉƵƚĂĐƟǀĂƟŽŶŶŽƟĮĐĂƟŽŶǁŝůůďĞŐŝǀĞŶǁŚĞŶƚŚĞĚŽŽƌůŽĐŬŝƐŽƉĞŶĞĚ
ͲͲdŚĞŬĞLJƉĂĚǁŝůůďĞĞƉƚǁŝĐĞǁŚĞŶƚŚĞĚŽŽƌůŽĐŬŝƐŽƉĞŶĞĚ
ͲͲdŚĞŬĞLJƉĂĚǁŝůůŐŝǀĞĂŽŶĞƐĞĐŽŶĚůŽŶŐďĞĞƉǁŚĞŶƚŚĞĚŽŽƌůŽĐŬŝƐŽƉĞŶĞĚ(Default)
ŽŽƌ&ŽƌĐĞĚͲKƉĞŶtĂƌŶŝŶŐ;>ŽĐĂƟŽŶϴϬͿ
15
22
Usually set output 2 to Momentary mode (Programming Option 501) for multi station systems and Start
One-Time
Time-Limit
User ID Entry of Code
NOTE:
●
●0-9
●
●
●
●
Programming Example :
3 2 8 9
2. Program a Visitor Code 1 3 7 8 at ID “0” for One-Time use:
3. Program a Visitor Code 2 3 0 8 9 at ID “1” with Time-Limit of 5 hours:
4. Program a Visitor Code 8 3 5 8 at ID “2” with Time-Limit of 10 hours:
Operaon :
16
Deleng Examples:
3289
a)
b)
c)
d)
e)
17
KƵƚƉƵƚƐϭΘϮĐĂŶďĞƉƌŽŐƌĂŵŵĞĚƚŽƚƌŝŐŐĞƌǁŝƚŚƚŚĞĨŽůůŽǁŝŶŐŽƉƟŽŶƐĨŽƌĂƉƌŽŐƌĂŵŵĞĚůĞŶŐƚŚ
ŽĨƟŵĞĨƌŽŵϭƚŽϵϵϵƐĞĐŽŶĚƐŽƌƚŽƚƌŝŐŐĞƌKEĂŶĚK&&ŝŶƚŽŐŐůĞǁŝƚŚĂƵƐĞƌĐŽĚĞŽƌƚŽƚƌŝŐŐĞƌKE
ǁŝƚŚĂŶĂĐĐĞůĞƌĂƚĞĚƐƚĂƌƚĐŽĚĞĂŶĚK&&ǁŝƚŚĂŶĨƵůůĚŝŐŝƚƵƐĞƌĐŽĚĞ
>ŽĐĂƟŽŶƐ Time Length ŽŶĮƌŵ
A) ϭʹϵϵϵ
B)
C)
D)
NOTE:
WƌŽŐƌĂŵŵŝŶŐ>ŽĐĂƟŽŶƐ
Ɣ >ŽĐĂƟŽŶƐϰϬϰϭϰϮĂŶĚϰϯĨŽƌKƵƚƉƵƚϭ
Ɣ >ŽĐĂƟŽŶƐϱϬϱϭϱϮĂŶĚϱϯĨŽƌKƵƚƉƵƚϮ
dŚĞƉƌŽŐƌĂŵŵŝŶŐŵĂŶŶĞƌŽĨƚŚĞƚǁŽŽƵƚƉƵƚƐĂƌĞĞdžĂĐƚůLJƚŚĞƐĂŵĞ
Programming Options for Outputs 1 & 2 ;^ĞĞ WƌŽŐƌĂŵŵŝŶŐ ^ƵŵŵĂƌLJ ŚĂƌƚ ^ĞĐƟŽŶ ĨŽƌ ŵŽƌĞ
ŝŶĨŽƌŵĂƟŽŶͿ
Ϳ>ŽĐĂƟŽŶϰϬŽƌϱϬDŽŵĞŶƚĂƌLJDŽĚĞǁŝƚŚƟŵĞůĞŶŐƚŚĨƌŽŵϭƚŽϵϵϵƐĞĐŽŶĚƐ;ĞĨĂƵůƚсϭƐĞĐŽŶĚͿ
dŚĞƌĞůĂLJŽƵƚƉƵƚƐĐĂŶďĞƉƌŽŐƌĂŵŵĞĚƚŽǁŽƌŬĨŽƌĂƟŵĞůĞŶŐƚŚĨƌŽŵƚŽƐĞĐŽŶĚƐƚŽ
ĐŽƉĞǁŝƚŚƚŚĞĚŽŽƌŽƉĞŶŝŶŐƌĞƋƵŝƌĞĚ
Ϳ>ŽĐĂƟŽŶϰϭŽƌϱϭ^ƚĂƌƚ^ƚŽƉDŽĚĞ;ƚŽŐŐůĞͿ
dŚĞƌĞůĂLJŽƵƚƉƵƚƐĐĂŶďĞƉƌŽŐƌĂŵŵĞĚƚŽƚƌŝŐŐĞƌKE;ƐƚĂƌƚͿĂŶĚK&&;ƐƚŽƉͿǁŝƚŚĂƵƐĞƌĐŽĚĞ
Ϳ>ŽĐĂƟŽŶϰϮŽƌϱϮ^ƚĂƌƚ^ƚŽƉDŽĚĞ;ƚŽŐŐůĞͿǁŝƚŚϮͲĚŝŐŝƚĐĐĞůĞƌĂƚĞĚŽĚĞ
dŚĞƌĞůĂLJŽƵƚƉƵƚƐĐĂŶďĞƉƌŽŐƌĂŵŵĞĚƚŽƚƌŝŐŐĞƌKEǁŝƚŚŽŶůLJƚŚĞĮƌƐƚϮĚŝŐŝƚƐŽĨĂƵƐĞƌĐŽĚĞĂŶĚ
K&&ǁŝƚŚĂĨƵůůƵƐĞƌĐŽĚĞ
Example:
ĂͿhƐĞƌŽĚĞ8 3 2 1ŝƐĂĨƵůůĐŽĚĞƚŚĞŶƚŚĞĮƌƐƚϮĚŝŐŝƚ8 3ŝƐƚŚĞĂĐĐĞůĞƌĂƚĞĚĐŽĚĞ
ďͿhƐĞƌŽĚĞ5 4 3 2 1ŝƐĂĨƵůůĐŽĚĞƚŚĞŶƚŚĞĮƌƐƚϮĚŝŐŝƚ5 4ŝƐƚŚĞĂĐĐĞůĞƌĂƚĞĚĐŽĚĞ
Ϳ>ŽĐĂƟŽŶϰϯŽƌϱϯ^ƚĂƌƚ^ƚŽƉDŽĚĞ;ƚŽŐŐůĞͿǁŝƚŚϯͲĚŝŐŝƚĐĐĞůĞƌĂƚĞĚŽĚĞ
dŚĞƌĞůĂLJŽƵƚƉƵƚƐĐĂŶďĞƉƌŽŐƌĂŵŵĞĚƚŽƚƌŝŐŐĞƌKEǁŝƚŚŽŶůLJƚŚĞĮƌƐƚϯĚŝŐŝƚƐŽĨĂƵƐĞƌĐŽĚĞĂŶĚ
K&&ǁŝƚŚĂĨƵůůƵƐĞƌĐŽĚĞ
Example:
ĂͿhƐĞƌŽĚĞ5 4 3 2 1ŝƐĂĨƵůůĐŽĚĞƚŚĞŶƚŚĞĮƌƐƚϯĚŝŐŝƚ5 4 3ŝƐƚŚĞĂĐĐĞůĞƌĂƚĞĚĐŽĚĞ
ďͿhƐĞƌŽĚĞ9 2 7 0 5 3ŝƐĂĨƵůůĐŽĚĞƚŚĞŶƚŚĞĮƌƐƚϯĚŝŐŝƚ9 2 7ŝƐƚŚĞĂĐĐĞůĞƌĂƚĞĚĐŽĚĞ
ŽŶĮŐƵƌĂƟŽŶŽĨKƵƚƉƵƚDŽĚĞƐĨŽƌKƵƚƉƵƚƐϭΘϮ;>ŽĐĂƟŽŶƐϰϬʹϰϯΘϱϬʹϱϯͿ
KƉĞƌĂƟŽŶ
ϭKƉĞƌĂƚĞKƵƚƉƵƚϭŝŶŵŽŵĞŶƚĂƌLJŵŽĚĞŽĨϱƐĞĐŽŶĚƐƵƐŝŶŐƵƐĞƌĐŽĚĞ8 3 2 1ƚŚĂƚǁĂƐ ƉƌŽŐƌĂŵŵĞĚ
ƉƌĞǀŝŽƵƐůLJ
ͲͲͲͲͲͲͲͲͲͲͲKƵƚƉƵƚƌĞůĂLJϭŽƉĞƌĂƚĞƐĨŽƌϱƐĞĐŽŶĚƐ
ϮKƉĞƌĂƚĞKƵƚƉƵƚϮŝŶ^ƚĂƌƚ^ƚŽƉŵŽĚĞƵƐŝŶŐƵƐĞƌĐŽĚĞ5 4 3 2 1ƚŚĂƚǁĂƐƉƌŽŐƌĂŵŵĞĚƉƌĞǀŝŽƵƐůLJ
ͲͲͲͲͲͲͲͲKƵƚƉƵƚƌĞůĂLJϮƐƚĂƌƚƐƚŽƉŝŶƚŽŐŐůĞǁŝƚŚƚŚĞƐĂŵĞƵƐĞƌĐŽĚĞ
ϯKƉĞƌĂƚĞKƵƚƉƵƚϮŝŶ^ƚĂƌƚ^ƚŽƉŵŽĚĞǁŝƚŚƚŚĞϯͲĚŝŐŝƚĐĐĞůĞƌĂƚĞĚĐŽĚĞƵƐŝŶŐƵƐĞƌĐŽĚĞ5 4 3 2 1
ŝĨŝƚǁĂƐƉƌŽŐƌĂŵŵĞĚƉƌĞǀŝŽƵƐůLJ
ͲͲͲͲͲͲͲͲͲͲͲͲͲͲͲͲͲKƵƚƉƵƚƌĞůĂLJϮƐƚĂƌƚƐǁŝƚŚĐĐĞůĞƌĂƚĞĚŽĚĞ
ͲͲͲͲͲͲͲͲͲKƵƚƉƵƚƌĞůĂLJϮƐƚŽƉƐǁŝƚŚ&ƵůůhƐĞƌŽĚĞ
NOTE:
ƔThe purpose of the accelerated Code -- ^ƚĂƌƚ ^ƚŽƉ ŵŽĚĞ ǁŝƚŚ ĂĐĐĞůĞƌĂƚĞĚ ĐŽĚĞ ĐĂŶ ďĞ
ĐŽŶƐŝĚĞƌĞĚĂƐƚǁŽƵƐĞƌĐŽĚĞƐǁŝƚŚŽŶĞĨŽƌƐƚĂƌƟŶŐĂŶĚƚŚĞŽƚŚĞƌĨŽƌƐƚŽƉƉŝŶŐƚŚĞŽƵƚƉƵƚKǁŶĞƌ
ĐĂŶŐŝǀĞƚŚĞĂĐĐĞůĞƌĂƚĞĚĐŽĚĞƚŽƚŚĞƐƚĂīƚŽƐƚĂƌƚĂƐLJƐƚĞŵ;ĨŽƌĞdžĂŵƉůĞĂŶĂůĂƌŵƐLJƐƚĞŵͿdŚĞ
ƐƚĂīĐĂŶŽŶůLJƐƚĂƌƚƚŚĞƐLJƐƚĞŵďƵƚĐĂŶŶŽƚƐƚŽƉŝƚKŶůLJƚŚĞŽǁŶĞƌĐĂŶƐƚŽƉ ƚŚĞƐLJƐƚĞŵǁŝƚŚƚŚĞ
ĨƵůůƵƐĞƌĐŽĚĞ
ƔdŚĞ^ƵƉĞƌhƐĞƌŽĚĞŝƐĂůǁĂLJƐǀĂůŝĚƚŽ^ƚĂƌƚ^ƚŽƉƚŚĞƌĞůĂLJŽƵƚƉƵƚƐ
Super User Code ͲͲͲͲͲͲͲKƵƚƉƵƚϭĐƟǀĂƚĞƐŽƌĞͲĂĐƟǀĂƚĞƐ
Super User Code ͲͲͲͲͲͲͲKƵƚƉƵƚϮĐƟǀĂƚĞƐŽƌĞͲĂĐƟǀĂƚĞƐ
WƌŽŐƌĂŵŵŝŶŐdžĂŵƉůĞƐ
ϭ^ĞƚŬĞLJƉĂĚƚŽƉƌŽŐƌĂŵŵŝŶŐŵŽĚĞǁŝƚŚŵĂƐƚĞƌĐŽĚĞĂŶĚŬĞLJdĂŬŝŶŐƚŚĞƉƌĞǀŝŽƵƐƉƌŽŐƌĂŵŵĞĚ
ŵĂƐƚĞƌĐŽĚĞ3 2 8 9ĂƐĞdžĂŵƉůĞŚĞƌĞ
2. Set Output 1 in momentary mode of 5 seconds:
3. Set Output 2 in Start / Stop Mode; OR
4. Set Output 2 in Start / Stop Mode with 3-digit Accelerated Start Code:
ϱdžŝƚƉƌŽŐƌĂŵŵŝŶŐŵŽĚĞďLJƉƌĞƐƐŝŶŐƚŚĞ
18 19
Operaon :
8 3 2 1
5 4 3 2 1
5 4 3 2 1
NOTE:
●The purpose of the accelerated Code --
●
Super User Code
Super User Code
Programming Examples:
3 2 8 9
2. Set Output 1 in momentary mode of 5 seconds:
3. Set Output 2 in Start / Stop Mode; OR
4. Set Output 2 in Start / Stop Mode with 3-digit Accelerated Start Code:
19
Type of Lock
Programming Codes for Type of Locks:
Important Note to Installer:
de-energized
(Default)
energized
20
Table of contents
Other APO Keypad manuals
APO
APO DK-9826 MK-II User manual
APO
APO DK-9350 User manual
APO
APO DK-9820 MK-II User manual
APO
APO DK-9866 MK-II User manual
APO
APO DK-9821 MK-II User manual
APO
APO DK-9520 MK-II User manual
APO
APO DK-9823 MK-II User manual
APO
APO DK-9865 MK-II User manual
APO
APO DK-9330 A User manual
APO
APO DK-9827 MK-II User manual
Popular Keypad manuals by other brands
Simons Voss Technologies
Simons Voss Technologies PinCode keypad manual
Elk
Elk Navigator -M1KPNAV user guide
Elk Products
Elk Products Keypad Arming Station ELK-M1KPAS Operation guide
Bosch
Bosch FMR-5000-C installation guide
Elsema
Elsema PCKeypad user manual
Simons Voss Technologies
Simons Voss Technologies PIN code keypad MobileKey quick guide
