APS Auto Parts Specialist IB04EBE8 User manual

(6”,5”,4)) RUNNING BOARD
For 2019 DODGE RAM 1500 CREW CAB
Rev:20181101
Page 1 of 4
Installation Instructions for IB04EBE8
by APS Auto Parts Specialist Inc.
Application: For 2019 Dodge Ram 1500 Crew Cab
Estimated Time: 1 to 2 hours
Disclaimer: Instructions intended for persons
aged 18+ please do not attempt without adult
supervision. Instructions are not intended to
replace professional installation. Damage
from improper installation, misuse or
modification to the product voids the
manufacturer’s warranty.

(6”,5”,4)) RUNNING BOARD
For 2019 DODGE RAM 1500 CREW CAB
Rev:20181101
Page 2 of 4
PARTS LIST:
QTY
Description
QTY
Description
2
Running Board(use for left or right)
12
M6 Nylon Lock Nuts
6
Mounting Brackets
18
M8X1.25 Nylon Lock Nuts
12
M6 x 20mm T-Bolts
18
M8 Flat Washers
12
M6 Flat Washers
PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.
1. Start the installation under the driver side of the vehicle. Locate the front (3) factory studs
along the inner side of the body panel, (Figure 1).NOTE: Chase threads on the studs first
before installing Brackets to remove paint buildup.
2. Select (1) Mounting Bracket. NOTE: All (6) Brackets are universal and will fit left or right side.
Attach the Mounting Bracket to the (3) factory studs with (3) M8 Flat Washers and (3) M8
Nylon Lock Nuts, (Figures 2 & 3). Leave brackets loose at this time.
3. Repeat Steps 1 & 2 to install the Universal Brackets in the center and rear mounting locations
along the body panel, (Figures 4 — 7).
4. Carefully unwrap and select the Driver/left side Running Board. NOTE: Use the illustration
above to help determine the correct Running Board. Place the Running Board on top of the
Brackets. IMPORTANT: Do not slide, (front to back), the Running Board on the Brackets or
damage to the finish may result. Locate the channel opening in the bottom of the Running
Board. Select (6) M6 T-Bolts, (Figure 8). Insert the T-Bolts into the channel in the bottom of
the Running Board closest to the Brackets, (Figure 9). Lift the Running Board up and guide
the studs through the Brackets.
5. Attach the Running Board to the Brackets with (6) M6 Flat Washers and (6) M6 Nylon Lock
Nuts, (Figures 10).
Mounting Brackets

(6”,5”,4)) RUNNING BOARD
For 2019 DODGE RAM 1500 CREW CAB
Rev:20181101
Page 3 of 4
6. Level and adjust the Running Board as necessary and fully tighten all hardware. NOTE:
Torque all M6 nylon lock nuts to 7 Ib-ft.
7. Repeat Steps 1—6 for Passenger/right side Running Board Installation.
8. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer
over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap
may be used also to clean the Running Board.
Driver/left Side Installation Pictured
Front
Front
(Fig 1) Driver/left side front mounting location
(3) M8 Flat Washers
(3) M8 Nylon Lock Nuts
(Fig 2) Attach Bracket to the (3) studs
(Fig 4) Driver/left side center mounting location
(Fig 3) Driver/left front side
Mounting Bracket installed
Front

(6”,5”,4)) RUNNING BOARD
For 2019 DODGE RAM 1500 CREW CAB
Rev:20181101
Page 4 of 4
Driver/left Side Installation Pictured
(Fig 6) Driver/left side rear mounting location
Rear
(Fig 10) Driver/left side Running Board attached
to Mounting Bracket at the front location
(2) M6 T-Bolts
(2) M6 Flat Washers
(2) M6 Nylon Lock Nuts
Front
(Fig 5) Driver/left center side
Mounting Bracket installed
(Fig 9) Slip M6 T-bolts into
the bottom channel
(3) M8 Flat Washers
(3) M8 Nylon Lock Nuts
(Fig 8) M6 T-Bolt
Rear
(Fig 7) Driver/left rear side
Mounting Bracket installed
(3) M8 Flat Washers
(3) M8 Nylon Lock Nuts