APS Auto Parts Specialist IB06EJJ9 User manual

(6",5”,4”)RUNNING BOARD
FOR 2001-2003 Ford F-150 SuperCrew Cab 4-Door (Incl. 04 Heritage Model)
Rev:20180801
Page 1of 3
Installation Instructions for IB06EJJ9
by APS Auto Parts Specialist Inc.
Application: FOR 2001-2003 Ford F-150 SuperCrew Cab 4-Door (Incl. 04 Heritage Model)
Estimated Time: 1 to 2 hours
Disclaimer: Instructions intended for persons aged
18+ please do not attempt without adult supervision.
Instructions are not intended to replace professional
installation. Damage from improper installation,
misuse or modification to the product voids the
manufacturer’s warranty.

(6",5”,4”)RUNNING BOARD
FOR 2001-2003 Ford F-150 SuperCrew Cab 4-Door (Incl. 04 Heritage Model)
Rev:20180801
Page 2of 3
PARTS LIST:
Item
QTY
Description
Item
QTY
Description
#1
2
Running Board(use for left or right)
#7
16
8mm Lock Washers
#2
2
Front Mounting Brackets(DFM/PFM)
#8
8
8mm Hex Nuts
#3
2
Rear Mounting Brackets（DRM/PRM）
#9
8
6-1.0mm x 20mm T-Bolts
#4
8
8mm Clip Nuts
#10
8
6mm x 22mm OD x 2mm Flat Washers
#5
16
8mm x 30mm Hex Bolts
#11
8
6mm Nylon Lock Nuts
#6
24
8mm IDx 24mmOD x2mm Flat Washers
PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ
INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS
RECOMMENDED.
2. Begin the installation by working on the driver side of the vehicle，Starting toward the front of
the driver side.
3. Remove the plugs as shown(Figure 1),select(2) 8mm clip nuts and insert into the round hole.
NOTE: Threaded nut must go towards the inside of the side panel,
4. Select a front bracket and bolt to the vehicle with (4)8mm Hex bolts,(6)8mm Washers,(4)8mm
Lock Washers and (2)8mm Hex Nuts(Figure 2), Do not tighten hardware at this time.
5. Move along the vehicle to the rear driver side, select a rear bracket, repeat Steps 3-4 to install
the rear brackets,Do not tighten hardware at this time.
6. Select a Running Board. Slip(8）6mm T-bolts into each bottom channel(Figure 3). Carefully
position the Running Board onto the (2) Mounting Brackets. IMPORTANT: Do not slide, (front
to back), the Running Board on the Brackets or damage to the finish may result. Attach the
Running Board to the Mounting Brackets with(2) 6mm T-bolts,(2)6mm flat washers and
(2)6mm lock nuts (Figures 4). Do not tighten at this time.
7. Level and adjust Running Board properly and tighten all hardware.
8. Repeat Steps 2—7 for passenger/right Running Board installation.
9. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, wax this product after installing. Regular waxing is recommended to add a
protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could
damage the finish.
DFM/PFM
DRM/PRM

(6",5”,4”)RUNNING BOARD
FOR 2001-2003 Ford F-150 SuperCrew Cab 4-Door (Incl. 04 Heritage Model)
Rev:20180801
Page 3of 3
For Polished Finishes: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild
soap may be used also to clean the Running Board.
For Black Finishes: Mild soap may be used to clean the Running Board.
Driver Side Installation Pictured
(Fig 1) Example only
Front
(Fig 2)Driver Front bracket installation picture
(2) 8mm x 30mm Hex Bolts
(2) 8mm Flat Washers
(2) 8mm Lock Washers
(2) 8mm Clip Nuts
(2) 8mm x 30mm Hex Bolts
(4) 8mm Flat Washers
(2) 8mm Lock Washers
(2) 8mm Hex Nuts
(2) 8mm Clip Nuts
(Fig 3) Slip 6mm T-bolts
into the bottom channel
(Fig 4)Running Board Installation
(2)M6 T-bolts
(2)M6 Flat Washers
(2)M6 Nylon Lock nuts