Aqua One Aqua Nano Bow 60 User manual

Assembly Instructions
Please keep for future reference
Important - Please read these instructions fully before starting assembly
Aqua Nano
Bow 60
Version 1 : 16/10/2017
ALR3437

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Make sure you have enough
space to layout the parts before
starting.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
Care and maintenance
Contact Us
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
Aqua Pacific UK Ltd.
Unit 10, Oriana Way
Nursling Industrial Estate
Southampton
SO16 0YU
Tel [phone]
Fax [phone]
[email protected]
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• Warning: This unit is heavy.
Please lift with care.
• Check you have all the
components and tools listed.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
Tools
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill
(do not use for
fitting screws)
Spirit
level
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: This unit must
be secured to a wall using the
overbalance protector kits
supplied.
• Dispose of all packaging
carefully and responsibly.

Panels
Please check you have all the panels listed below
1Left Side (DF-00018252)
(69.4 x 28cm)
4Top (DF-00018250)
(60 x 38cm)
2Right Side (DF-00018253)
(69.4 x 28cm)
3Divider (DF-00018254)
(69.4 x 32.8cm)
6Back Panel (DF-00018255)
(69.4 x 39.6cm)
5Base (DF-00018251)
(60 x 38cm)
7Left Door (DF-00018256)
(68.8 x 28.3cm)
8Right Door (DF-00018257)
(68.8 x 28.3cm)

Fittings
Please check you have all the fittings listed below
A B
Large Metal Dowel (F901) x 8
C
D E
Large Locking Cam
Nut (F900) x 8
G
F
Wooden Dowel (F22) x 16
40mm Screw (F910) x 8
Large 13mm Screw (F63) x 12
L
Hinge Plate (F523) x 4
25mm Screw (F95) x 4 25mm Screw (F50) x 6
N a
Magnetic catch
(F38) x 2
N b
Magnetic
plate (F41) x 2
I
Feet (F854) x 6
J
Handle (F315) x 2
K
Overbalance Protector
Kit (F474) x 2
M
Hinge (F522) x 4
Small 13mm Screw (F109) x 2
H

C
C
C
C
Step 1
Step 2
Step 3
Prepare the Left Side
Tap 4 Wooden Dowels
into the Left Side.
Insert 2 Large Locking
Cam Nuts into the Left
Side.
Fit 2 Hinge Plates onto
the Left Side, making
sure that the slot is
facing towards the
finished front edge.
Prepare the Right Side
Tap 4 Wooden Dowels
into the Right Side.
Insert 2 Large Locking
Cam Nuts into the Right
Side.
Fit 2 Hinge Plates onto
the Right Side, making
sure that the slot is
facing towards the
finished front edge.
LB10mm
C
L
Finished
Front Edge
L
L
B
B
C
C
1
B
B
C
C
L
L2
Finished
Front Edge
Fit the Left and Right
Side to the Base
Push the Left and Right
Side onto the Base and
fit them using four 40mm
Screws.
D
D
D
D
2
1
5
Finished
Front Edge
Finished
Front Edge