Aqua One Oakstyle Chic 3+2 Unit User manual

Assembly Instructions
Please keep for future reference
Important - Please read these instructions fully before starting assembly
Oakstyle Chic 3+2 Unit
Version 1 : 21/07/2020
ALR3664

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Make sure you have enough
space to layout the parts before
starting.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
Care and maintenance
Contact Us
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
Aqua Pacific UK Ltd.
Unit 10, Oriana Way
Nursling Industrial Estate
Southampton
SO16 0YU
Tel [phone]
Fax [phone]
[email protected]
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• Warning: This unit is heavy.
Please lift with care.
• Check you have all the
components and tools listed.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: This unit must
be secured to a wall using the
overbalance protector kits
supplied.
• Dispose of all packaging
carefully and responsibly.
Tools
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Flat-head
screwdriver
Electric drill
(do not use for
fitting screws)
Spirit
level

Panels
Please check you have all the panels listed below
1Drawer Front
(DF-00023486)
(42.35 x 21.7cm)
4Drawer Back
(WRP-00000376)
37.9 x 16.5cm
2Left Drawer Side
(WRP-00000081)
35 x 16.5cm
3
6Left Side
(DF-00023494)
(64.5 x 37.1cm)
7Right Side
(DF-00023493)
(64.5 x 37.1cm)
10 Top (DF-00020378)
(123.15 x 41cm)
Right Drawer Side
(WRP-00000082)
35 x 16.5cm 5Drawer Base
(TDF-00020388)
39 x 34.7cm
11 Base (DF-00020379)
(123.15 x 37.2cm)
8Left Divider
(DF-00023498)
(64.5 x 37.1cm)
9Right Divider
(DF-00023497)
(64.5 x 37.1cm)
12 Back Panel (DF-00020353)
(78.5 x 39.6cm) x 2
x 3 x 3 x 3
x 2
x 3
x 3
13 H-Frame LH Upright
(DF-00021046)
(37.1 x 12.5cm)
14 H-Frame RH Upright
(DF-00021249)
(37.1 x 12.5cm)
15 H-Frame Cross Rail (DF-00021047)
(112.65 x 12.5cm)
16 LH Door
(DF-00023484)
(65.7 x 39.6cm)
17 RH Door
(DF-00023487)
(65.7 x 39.6cm)
Identification
hole
Identification
hole

Fittings
Please check you have all the fittings listed below
Bag 1
A B
Large Metal Dowel (F901) x 16
C
D
Large Locking Cam
Nut (F900) x 16
H
Allen Key (F36) x 1
G
45mm Screw (F65) x 4
20mm Screw (F461) x 4
I
Wooden Dowel (F22) x 24
9mm Screw (F73) x 12
Shelf stud (F110) x 6
These are for fixing the Hood.
See separate instructions for fitting details.
*
L
F
40mm Screw (F910) x 8
E
50mm Screw (F49) x 4
13mm Screw (F63) x 8
KJ
Door Buffers (F137) x 6
Bag 2
Individual Bags
QP
S
Overbalance protector
kit (F474) x 2
A
Large Metal Dowel (F901) x 6
M
O
9mm Screw (F74) x 6
T
Drawer runner (F1004) x 6
Back Holder (F639) x 12
P
R
Pre-mounted hinge (F328) x 4
Handle (F341) x 5
20mm Screw (F461) x 4
J
Small Locking Cam
Nut (F900) x 6
Knock-in Peg (F171GY) x 12
N

Step 1
Step 2
Step 3
Prepare the 3 pair of
Drawer Sides
Insert a Small Locking
Cam Nut into each Left
Drawer Side and each
Right Drawer Side.
Note: The arrow on the
Small Locking Cam Nut
must point towards the
hole in the edge of the
panel.
Attach the Drawer
Sides to the Drawer
Fronts
Push the Drawer Sides
onto the back of the
Drawer Fronts.
Turn the Small Locking
Cam nuts on the Drawer
Sides.
Note: Turn the Small
Locking Cam nuts
clockwise to secure the
panels - more than 1/2 a
turn.
A
M
M
Prepare the 3 Drawer
Fronts
Screw 2 Metal Dowels
into each Drawer Front.
Note: Tighten the Metal
Dowels up fully against
the panel.
Stick a door buffer
into the top corners of
each Drawer Front.
Use Bag 2 for steps 1 - 7
A
K
K
A
1
M
3
x 3
x 3 x 3
x 3
M
2
1
2
3

N
N
Step 4
Step 5
Step 8
Fit the Drawer Bases
Slide the Drawer Base
down the grooves in the
Drawer Sides and down
into the groove in the
Drawer Front.
Fit the Drawer Backs
Fit the Drawer Back
between the Drawer
Sides.
Make sure that the
Drawer Base fits into the
groove in the Drawer
Back.
Hold the Drawer Back
in position and tap the
Knock-in Pegs through
the holes in the Drawer
Sides.
Step 6
Attach the Handles
Attach a Handle to each
Drawer Front using two
20mm Screws from Bag 1.
Step 8
Step 7
Fit the Wedgefixes
Turn the 3 drawer
assembies over and slide
2 Wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws. P
The Drawer assembly
must be square before
fitting the wedgefixes
x 3
1
3
2
5
x 3
x 3
x 3
3
5
2
4
N
N
P
PP
P
Q
J
J

Finished
front edge
Finished
front edge
C
B
C
Step 8Use Bag 1 for steps 8 - end
8
8
B
Prepare the Left Divider
a: Place a runner on the
Left Divider, as shown.
Slide back the top of
Runner and use the 2nd
hole from the front to fit
the first 9mm Screw.
b: Slide the Runner
back the other way and
fit the second 9mm
Screw into the
corresponding hole in the
Left Divider.
c: Tap 2 Wooden
Dowels into the Left
Divider.
Insert 2 Large Locking
Cam Nuts into the
Left Divider.
a:
b:
c:
K
T
I
I
T
8
I
I
I
C
C
Finished
front edge
I
T
I
T
Finished
front edge

C
B
C
Step 9
Finished
front edge
I
T
a:
b:
c:
I
T
7
7
7
K
B
C
C
Prepare the Right
Divider
a: Place a runner on the
Right Divider, as shown.
Slide back the top of
Runner and use the 2nd
hole from the front to fit
the first 9mm Screw.
b: Slide the Runner
back the other way and
fit the second 9mm
Screw into the
corresponding hole in the
Right Divider.
c: Tap 2 Wooden
Dowels into the Right
Divider.
Insert 2 Large Locking
Cam Nuts into the
Right Divider.
I
T
I
T
K
K
Finished
front edge
Finished
front edge
Finished
front edge
Identification
hole

Finished
front edge
Finished
front edge
Finished
front edge
Step 10
F
F
Fit the Left Divider to
the Base
Attach the Left Divider to
the Base using two
40mm Screws.
8
11
11
F
F
9
Fit the Right Divider
Attach the Right Divider
to the Base using two
40mm Screws.
Step 11

Step 12
Prepare the 2 H-Frame
Cross Rails
Tap 2 Wooden Dowels
into the H-Frame Cross
Rail.
Insert 2 Large Locking
Cam Nuts into the
H-Frame Cross Rail.
Note: The arrow on the
Large Locking Cam Nuts
must point towards the
hole in the edge of the
panel.
Step 8
Step 13
Step 8
Step 14
Finished
front edge
Finished
front edge
Note: Holes on
the top edge
A
Prepare the 2 H-Frame
Uprights
Screw 2 Metal Dowels
into the H-Frame LH
Upright and the H-Frame
RH Upright.
A
A
A
13 14
C
B
C
15
C
B
C
15
Join the 2 H-Frame
Cross Rails to the
H-Frame LH Upright
Push the 2 H-Frame
Cross Rails onto the
H-Frame LH Upright.
Use a flat-head
screwdriver to tighten the
2 Large Locking Cam
Nuts fitted to the 2
H-Frame Cross Rails.
Finished
front edge
x 2
13
15
15
Identification
hole