Aqua One Cabinet 53446 User manual

Assembly Instructions
Please keep for future reference.
Important - Please read these instructions fully before starting assembly
Version 1 - 25/11/19
60cm Cabinet
Suitable for AquaSys 150 or ReefSys 180 Aquariums
AquaSys ReefSys
by

Safety Care and Advice
IMPORTANT: Please read these instructions before starting assembly
• Warning: This unit is heavy.
Please lift with care.
• Check you have all the components
and tools listed.
• Remove all ttings from the plastic
bags and separate them into their
groups.
• Keep children and animals away from
the work area, small parts could choke
if swallowed.
• Parts of the assembly will be easier
with 2 people.
• Make sure you have enough space
to layout the parts before starting.
• Assemble the item as close to its
nal position (in the same room) as
possible.
• Assemble on a soft level surface to
avoid damaging the unit or your
oor (use opened out unit carton).
• We do not
recommend the use
of power drill/
drivers for inserting
screws, as this could
damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging carefully and
responsibly.
Care and maintenance
Contact Us
• Only clean using a damp cloth and
mild detergent, do no use bleach or
abrasive cleaners.
• From time to time check that there
are no loose screws on this unit.
• This product should not be discarded
with household waste. Take to your
local authority waste disposal centre.
Aqua Pacic UK Ltd.
Unit 1, Mauretania Road, Nursling
Industrial Estate, Southampton
SO16 0YS
Tel [phone]
Fax [phone]
sales@aquapacic.co.uk
www.aquaone.co.uk
Tools
Measuring
Tape
Spirit Level Cross-head
screwdriver
Hammer
Eye protection
(when using a
hammer)
Silicone
Silicone

Panels
Please check you have all the panels listed below.
2x Side panels
764 x 530mm
2 x Wide back brace
764 x 200mm
1x Base
604 x 531mm
1x Top
604 x 531mm
1x Door
786x596mm
BA
C D
E

Fittings
Please check you have all the ttings listed below.
30x 15mm Large
Locking Cam Nut 30x Cam Bolts
1 2 4x Hinges 3
4x Hinge Plates
46x Hammer-in Glides 512x 3.5x15mm Screws 6
2x Push Catch
71x Aperture Trim Ring 8

Step One
Lay side panels (A) on the
oor with holes facing
upwards.
Fit 6x Cam ttings (1) into
large holes with cross facing
up and the arrow facing the
edge of the board.
Screw 3x Cam Bolts (2) into
the 5mm holes along the back
edge.
Attach the two hinge plates
(4) to the side that has the
two pairs of 5mm holes at the
front edge eith the at edge
at the front.
Repeat on both panels.
A
1
1
1
1
1
1
A
2
2
2
A
4
4

Step Two
Fit Cam Fittings (1) into the 7
holes of the Wide Back Braces
(B).
Attach the raw edge of the
Wide Back Braces to the back
edge of the sides giving the
Cam Fittings a half turn with
the screwdriver.
Repeat for both panels.
1
1
1
1
1
1
1
B
A
B

Step Three
Using a hammer, t glides (5)
to the underside of the base
panel (C) using the pip marks
as a guide for tment then
turn the base over to have the
5mm holes facing upwards.
Screw in cam bolts (2) into all
of the 5mm holes
C
2
2
2
2
2
22
22
C
Turn over
2
5
5
5
5

Step Four
Drop sides with attached back
braces onto the cams on the
base ensuring the side that has
the hinge plates is on the left
hand side as you face it.
Give all cam ttings a half turn
with the screwdriver.
C
A
B
B
A

Step Five
Lay top panel (D) with holes
facing upwards, screw cam
bolts (2) into all 5mm holes.
Using 2 of screws (6) attach the
bracket for the push catch (7)
to the pip marks then attach
push catch to the bracket by
clipping in at the back and
pushing down at the front
until you hear a click.
Turn top over and attach to
sides and back braces as with
the base. D
2
2
2
2
2
22
22
2
C
7
6
6
A
A
B
B
D
Turn over

Step Six
Lay door (E) on oor with
the hinge holes facing
up, place hinges (3) into
holes and screw in using
remaining screws (6).
Hook hinge arms into the
front of the hinge plate and
push in at the back of the
arm until they click. Adjust
hinges using adjustment
screws as necessary.
Adjust the push catch (7) as
necessary by twisting in or
out.
6
6
66
E
3
3
C
A
A
D
E
7

Step Seven
From the inside of the
cabinet push aperture trim
ring (8) through the hole in
the top of the cabinet.
We highly recommenced
securing with silicone to
seal the edge and protect
the chipboard.
7
A
A
B B
C
D
Silicone