Aqua One Oakstyle 145 User manual

Assembly Instructions
Please keep for future reference
Important - Please read these instructions fully before starting assembly
Oakstyle 145
Version 2 : 09/10/2017
ALR3414

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Make sure you have enough
space to layout the parts before
starting.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
Care and maintenance
Contact Us
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
Aqua Pacific UK Ltd.
Unit 10, Oriana Way
Nursling Industrial Estate
Southampton
SO16 0YU
Tel [phone]
Fax [phone]
[email protected]
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• Warning: This unit is heavy.
Please lift with care.
• Check you have all the
components and tools listed.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
Tools
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill
(do not use for
fitting screws)
Spirit
level
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: This unit must
be secured to a wall using the
overbalance protector kits
supplied.
• Dispose of all packaging
carefully and responsibly.

Panels
Please check you have all the panels listed below
9 10
Divider (DF-00011544)
(64.5 x 33.4cm)
Left Side (DF-00011541)
(75.5 x 35.7cm)
7
Right Side (DF-00011542)
(75.5 x 35.7cm)
12 Top (DF-00011540)
(88 x 41cm)
1Left Drawer
Front (DF-00011548)
(34.2 x 16.2cm)
2Right Drawer
Front (DF-00011549)
(34.2 x 16.2cm)
3Left Drawer
Side (W330-124LH)
(33 x 12.4cm) x 2
4Right Drawer
Side (W330-124RH)
(33 x 12.4cm) x 2
5Drawer Back
(W303-124)
(30.3 x 12.4cm) x 2
6Drawer Base
(T314-327)
(31.4 x 32.7cm) x 2
11 Fascia (F755-70)
(755 x 70mm) x 2
13 Base (DF-00011543)
(69.5 x 33.4cm)
14 Shelf (DF-00011545)
(33.6 x 33.2cm)
Plinth (DF-00011547)
(69.5 x 9.5cm) x 2
8
17 Back (DF-00011550)
(75.5 x 39.6mm)
15 Left Door (F492-342LH)
(492 x 342mm)
16 Right Door (F492-342RH)
(492 x 342mm)

Fittings
Please check you have all the fittings listed below
A B
Large Metal Dowel (F901) x 20
C
D E
Knock-in Peg
(F171GY) x 8
Large Locking Cam
Nut (F900) x 22
Small Locking Cam
Nut (F900) x 4
H IG
Plastic Nail (F91) x 7
Wooden Dowel (F22) x 20
45mm Screw (F65) x 2
F
O
L
Wedgefix (F639) x 4
19mm Screw (F461) x 8
M
Shelf stud (F110) x 10
J
9mm Screw (F74) x 4
K
9mm Screw (F73) x 8
N
Door Buffer (F137) x 6
Handle (F287) x 4
Drawer runner (F1004) x 4
P
Pre-mounted
hinge (F419) x 4
Q
Overbalance protector
kit (F474) x 2
R
Quickfit dowel (F545) x 6
6 of these are required for Hood fixing.
See seperate instructions for fitting details.
*
S
40mm Screw (F910) x 2

2
Step 1
Step 2
Step 3
Prepare the Drawer
Sides
Insert a Small Locking
Cam Nut into the 2 Left
Drawer Sides and the 2
Right Drawer Sides.
Note: The arrow on the
Small Locking Cam Nut
must point towards the
hole in the edge of the
panel.
Attach the Drawer
Sides to the Drawer
Fronts
Push the Left Drawer
Sides and Right Drawer
Sides onto the back of
the Drawer Fronts.
Turn the Small Locking
Cam nuts on the Left
Drawer Sides and right
Drawer Sides.
Note: Turn the Small
Locking Cam nuts
clockwise to secure the
panels - more than 1/2 a
turn.
A
A
B
B
BB
Prepare the 2 Drawer
Fronts
Screw 2 Metal Dowels
into each of the Drawer
Fronts.
Note: Tighten the Metal
Dowels up fully against
the panels.
Stick 2 Door Buffers into
the corners of each
Drawer Front, as shown.
34
BB
34
3
4
1
1
A
G
G
A
3
4
A
A
G
G
Shallow I.D. hole
2

2
Step 4
Step 5
Step 8
Fit the Drawer Bases
Slide the Drawer Bases
down the grooves in the
Drawer Sides and down
into the groove in the
Drawer Fronts.
Fit the Drawer Back
Fit the Drawer Backs
between the Drawer
Sides.
Make sure that the
Drawer Base fits into the
groove in the Drawer
Back.
Hold the Drawer Back
in position and tap the
Knock-in Pegs through
the holes in the Drawer
Sides.
Step 6
Attach the Handle
Attach a Handle to each
of the Drawer Fronts
using two 19mm Screws.
Step 8
Step 7
Fit the Wedgefixes
Turn the drawer
assemblies over and
slide 2 Wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
C
C
C
C
D
D
D
3
4
3
5
64
1
I
I
O
1
The Drawer assembly
must be square before
fitting the wedgefixes.
C
C
C
C
3
4
3
5
64
I
I
O
2
D
D
6 6

R
R
R
F
F
Left Fascia - holes
nearest this side
Step 8
Step 9
Prepare the 2 Fascias
Check that the holes are
in the same place as the
diagrams, as one will be
the Left Fascia and one
will be the Right Fascia.
Tap a Wooden Dowel
into each of the 2
Fascias.
Note: Wooden Dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
F
F
10mm
F
11
11
E
E
E
E
E
9
Right Fascia - holes
nearest this side
Prepare the Left Side
Tap 2 Wooden Dowels
into the Left Side.
Insert 5 Large Locking
Cam Nuts into the
Left Side.
Note: The arrow on the
Large Locking Cam Nuts
must point towards the
hole in the edge of the
panel.
Push 3 of the Quickfit
Dowels as far as they will
go into the Left Side.
Note: Only the plastic
thread of the Quickfit
Dowel sticks out from the
panel.
R
E

Step 10
Finish preparing the
Left Side
a: Place a runner on the
Left Side as shown. Slide
back the top of Runner
and use the 2nd hole
from the front to fit the
first 9mm Screw.
b: Slide the Runner
back the other way and
fit the second 9mm
Screw into the
corresponding hole in the
Left Side.
Screw 4 metal dowels
into the Left Side.
9
9
AA
A
A
K
K
N
K
a:
b:
Step 11
N
K
11
9
Dowel
this end
Fit the Left Fascia to
the Left Side
Push the Left Side down
onto the Left Fascia.
Use a screwdriver to
tighten the 3 Large
Locking Cam Nuts
fitted to the Left Side.
Note: Turn the Large
Locking Cam Nuts as far
as they will go - more
than 1/2 a turn.
Important: Make sure
there is no gap between
the fitted panels.

Step 12
Step 13
F
F
E
E
E
E
E
10
Fit the Right Fascia to
the Right Side
Push the Right Side
down onto Right Fascia.
Use a screwdriver to
tighten the 3 Large
Locking Cam Nuts
fitted to the Right Side.
Note: Turn the Large
Locking Cam Nuts as far
as they will go - more
than 1/2 a turn.
Important: Make sure
there is no gap between
the fitted panels.
Dowel
this end
10
11
Prepare the Right Side
Tap 2 Wooden Dowels
into the Right Side.
Insert 5 Large Locking
Cam Nuts into the
Right Side.
Push 3 of the Quickfit
Dowels as far as they will
go into the Right Side.
R
R
R

F
F
Step 14
E
E
E
E
Prepare the Base
Tap 4 Wooden Dowels
into the Base.
Insert 4 Large Locking
Cam Nuts into the Base.
Finished
front edge
10
13
13
Finished
front edge
Step 16
Fit the Base
Push the Base onto the
Right Side.
Use a screwdriver to
tighten the 2 Large
Locking Cam Nuts
fitted to the Base.
Step 15
F
F
A
A
A
a:
b:
A
Finished
front edge
K
N
K
N
K
10
10
Finish preparing the
Right Side
a: Place a runner on the
Right Side as shown.
Slide back the top of
Runner and use the 2nd
hole from the front to fit
the first 9mm Screw.
b: Slide the Runner
back the other way and
fit the second 9mm
Screw into the
corresponding hole in the
Right Side.
Screw 4 metal dowels
into the Right Side.

Step 17
Step 19
F
Step 18
Fit the Plinths
Push the 2 Plinths onto
the Right Side.
Use a screwdriver to
tighten the Large Locking
Cam Nut fitted to each
Plinth.
F
E
E
F
F
E
E
Prepare the 2 Plinths
Tap 2 Wooden Dowels
into each of the Plinths.
Insert 2 Large Locking
Cam Nuts into each of
the Plinths.
8
8
10
8
8
8
13
8
9
Fit the Left Side
Push the Left Side onto
the Base and the Plinths.
Use a screwdriver to
tighten the 4 Large
Locking Cam Nuts
fitted to the Base and
Plinths.
Support the Plinth
until the Left Side
has been fitted

F
F
Step 20
Prepare the Divider
a: Place a Runner on
the Divider as shown.
Slide back the top of
Runner and use the 2nd
hole from the front to fit
the first 9mm Screw.
b: Slide the Runner
back the other way and
fit the second 9mm
Screw into the
corresponding hole in the
Divider.
c: Tap 4 Wooden
Dowels into the Divider.
Insert 2 Large Locking
Cam Nuts into the
Divider.
Turn the panel
over
d: Place a Runner on
the Divider as shown.
Slide back the top of
Runner and use the 2nd
hole from the front to fit
the first 9mm Screw.
e: Slide the Runner
back the other way and
fit the second 9mm
Screw into the
corresponding hole in the
Divider.
Turn the
panel over
K
K
N
a:
N
K
7
b:
d:
e:
7
c: 7
K
E
E
F
F
K
N
K
K
N
7
7

Packaging
piece
Packaging
piece
Packaging
piece
Packaging
piece
Step 21
Fit the Divider
Push the Divider onto the
Base and secure it with 2
40mm Screws.
A
A
A
A
A
A
A
A
12
Step 22
Prepare the Top
Screw 8 Metal Dowels
into the Top.
Fit the 2 Brackets from
the Overbalance
Protector Kits to the
shallow mark-holes
drilled into the Top
using 1 of their Screws.
Note: Only fit 1 of the
Screws, the other 1 will
be fitted later.
Q
Q
Q
13
7
S
S
Raise the assembly
To make it easier to fit
the Top Panel, place
packaging pieces
underneath the Side
Panels and Divider to
raise the assembly.
Step 23
Packaging
piece

12
Step 24
F
F
Step 26
Fit the Back
Push the Back onto the
Top.
Use a screwdriver to
tighten the 2 Large
Locking Cam Nuts fitted
to the Back.
Fix the Back to the Base
with two 45mm Screws.
Prepare the Back
Tap 2 Wooden Dowels
into the Back.
Insert 2 Large Locking
Cam Nuts into the Back.
E
E
17
Fit the Top
Push the Top onto the
assembly.
Use a screwdriver to
tighten the 6 Large
Locking Cam Nuts fitted
to the Divider and the
Sides.
10
9
7
Step 25
12
H
H
17
13

Step 27
a:
b: QQ
Top
This unit must be fixed to a wall using the
2 Overbalance Protector Kits provided
Secure the unit to a
wall
a: Before fitting the unit
to a wall, use a spirit
level to check the top of
the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level.
To prevent possible
overbalancing this unit
must be secured to a
suitable wall by fitting the
2 Overbalance Protector
Kits to a wall.
b: Push the unit up
against the wall and slide
the Brackets against the
wall. Fit the 2nd Screw
from the kits into the
underside of the Top
panel.
Mark the slot at the back
of the Brackets for drilling
into the wall.
Wall fixings are not
supplied as they will need
to suit the wall type.
Fit the Plastic Nails
Tap 2 Plastic Nails into
the bottom edge of each
of the Sides.
Tap a Plastic Nail into
the centre of the bottom
edge of the 2 Plinths and
the Back.
Take care when drilling
the wall that you do not
drill into any pipes, wires
etc. If in doubt, consult
an expert.
L
LL
L
L
L
L
Step 28
Q
Q

Step 29
Fit the Shelf
The Shelf can be fitted to
either side of the unit.
Insert 4 Shelf Studs, at
the required height.
Lower the Shelf down
onto the Shelf Studs.
Fit the Drawers
Slide both the Runners
forward and locate the
Drawer Sides between
them, lining up their
holes with the 2nd
'threaded' holes in the
Runners.
Working from the inside
of the Drawer, insert 2
9mm Screws through the
Drawer Sides and out
into the 2nd threaded
hole in the Runner.
Note: Do not overtighten
the Screws. If they catch
on the Runners you may
need to loosen them
slightly.
2nd threaded
hole
N
J
The Runners could
have sharp edges and
we recommend that
you position them
using a Screwdriver.
Prepare the 2 Doors
Push fit 2 Hinges into
each Door and secure
them by tightening up
their 2 screws.
P
P
15 P
P
16
Step 31
Step 30
The 6 Shelf Studs you have left are
required for Hood fixing.
See seperate instructions for fitting details.
*
Mx 4
14
J
J
1
2

Step 32
Step 33
Fit the Doors and its
Handles
Line up the 2 screws in
the top Hinge with the 2
holes at the top of the
Sides and push them in.
Now push in the other
Hinge.
When both of the Hinges
have been pushed into
place, tighten their 2
screws.
Attach a Handle to each
Door using two 19mm
Screws.
Press the Screws into
the holes in the panels
When the Hinges have
been pushed in,
tighten up their Screws
P
P
a:
b:
c:
Adjust the Doors if
needed
a: Height adjustment.
Loosen Screws A on
Hinge Plates and move
Door up or down as
required.
Retighten Screw A.
b: Forward and Back
adjustment.
Loosen Screw B on
Hinge Plate and move
Door in or out as
required.
Retighten Screw B.
c: Sideways
adjustment.
To move Door ‘out’
loosen Screw C.
To move Door ‘in’ tighten
Screw C.
A
A
B
C
O
I
Note: Fit the
top hinge 1st
16
15
I

G
Step 34
Fit the Door Buffers
Stick a Door Buffer onto
the bottom corner of
each Door where they
will hit the Base.
16
15
G