Aqua One Aqua Nano Bow 80 User manual

Assembly Instructions
Please keep for future reference
Important - Please read these instructions fully before starting assembly
Aqua Nano
Bow 80
Version 1 : 17/10/2017
ALR3438

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Make sure you have enough
space to layout the parts before
starting.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
Care and maintenance
Contact Us
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
Aqua Pacific UK Ltd.
Unit 10, Oriana Way
Nursling Industrial Estate
Southampton
SO16 0YU
Tel [phone]
Fax [phone]
[email protected]
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• Warning: This unit is heavy.
Please lift with care.
• Check you have all the
components and tools listed.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
Tools
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill
(do not use for
fitting screws)
Spirit
level
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: This unit must
be secured to a wall using the
overbalance protector kits
supplied.
• Dispose of all packaging
carefully and responsibly.

Panels
Please check you have all the panels listed below
1Left Side (DF-00018261)
(69.4 x 29cm)
4Top (DF-00018259)
(80 x 40cm)
2Right Side (DF-00018262)
(69.4 x 29cm)
3Divider (DF-00018263)
(69.4 x 34.8cm)
6Back Panel (DF-00018264)
(69.4 x 39.6cm)
5Base (DF-00018260)
(80 x 40cm)
7Left Door (DF-00018265)
(68.8 x 38.3cm)
8Right Door (DF-00018266)
(68.8 x 38.3cm)

Fittings
Please check you have all the fittings listed below
A B
Large Metal Dowel (F901) x 8
C
D E
Large Locking Cam
Nut (F900) x 8
G
F
Wooden Dowel (F22) x 16
40mm Screw (F910) x 8
Large 13mm Screw (F63) x 12
L
Hinge Plate (F523) x 4
25mm Screw (F95) x 4 25mm Screw (F50) x 6
N a
Magnetic catch
(F38) x 2
N b
Magnetic
plate (F41) x 2
I
Feet (F854) x 6
J
Handle (F315) x 2
K
Overbalance Protector
Kit (F474) x 2
M
Hinge (F522) x 4
Small 13mm Screw (F109) x 2
H

Finished
Front Edge
Finished
Front Edge
C
C
Finished
Front Edge
C
C
Step 1
Step 2
Step 3
Prepare the Left Side
Tap 4 Wooden Dowels
into the Left Side.
Insert 2 Large Locking
Cam Nuts into the Left
Side.
Fit 2 Hinge Plates onto
the Left Side, making
sure that the slot is
facing towards the
finished front edge.
Prepare the Right Side
Tap 4 Wooden Dowels
into the Right Side.
Insert 2 Large Locking
Cam Nuts into the Right
Side.
Fit 2 Hinge Plates onto
the Right Side, making
sure that the slot is
facing towards the
finished front edge.
LB10mm
C
L
Fit the Left and Right
Side to the Base
Push the Left and Right
Side onto the Base and
fit them using four 40mm
Screws.
B
C
B
C
L
L
1
Finished
Front Edge
B
C
B
C
L
L2
D
D
D
D
2
1
5

C
C
C
C
Step 4
Prepare the Back
Tap 4 Wooden Dowels
into the Back.
Insert 2 Large Locking
Cam Nuts into the
Back.
Step 8
Step 6
Prepare the Divider
Tap 4 Wooden Dowels
into the Divider.
Insert 2 Large Locking
Cam Nuts into the
Divider.
Step 5
Fit the Back
Push the Back onto the
Base and secure it using
two 40mm Screws.
B
C
B
C
6
D
D
6
B
C
B
C
Finished
Front Edge
3

Step 7
Step 8
Fit the divider
Push the Divider onto the
Base and fit it using 2
40mm screws.
a:
b:
D
D
Finished
Front Edge
A
A
A
A
A
A
A
A
4
3
4
K
Prepare the Top
a: Screw 8 Metal Dowels
into the Top.
b: Fit the 2 Magnetic
Catches to the shallow
mark-holes in the Top
using 4 of the Large
13mm Screws.
Loosely fit the 2 Brackets
from the Overbalance
Protector Kits to the
shallow mark-holes
drilled into the Top
using 1 of their Screws.
Note: Only fit 1 of the
Screws, the other 1 will
be fitted later.
N a
G
G
G
Large 13mm Screw Small 13mm Screw
H

Step 9
Step 8
Step 10
A
B
Fit the Top
Push the Top onto the
assembly.
Use a screwdriver to
tighten the 8 Large
Locking Cam Nuts fitted
to the Sides, Divider and
Back.
Fit the 6 Feet
Screw the Feet onto the
mark-holes in the Base
using the six 25mm
Screws.
4
I
F5

Step 11
a:
b: K K
Top
This unit must be fixed to a wall using the
2 Overbalance Protector Kits provided
Secure the unit to a
wall
a: Before fitting the unit
to a wall, use a spirit
level to check the top of
the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level.
To prevent possible
overbalancing this unit
must be secured to a
suitable wall by fitting the
2 Overbalance Protector
Kits to a wall.
b: Push the unit up
against the wall and slide
the Brackets against the
wall. Fit the 2nd Screw
from the kits into the
underside of the Top
panel.
Mark the slot at the back
of the Brackets for drilling
into the wall.
Wall fixings are not
supplied as they will need
to suit the wall type.
Take care when drilling
the wall that you do not
drill into any pipes, wires
etc. If in doubt, consult an
expert.
K
K

Step 12
M
G
G
M
G
G
M
G
G
M
G
G
7
8
Prepare the 2 Doors
Push fit 2 Hinges into
each of the 2 Doors.
Secure each hinge with
two Large 13mm Screws
fitted using the shallow
mark holes.
Fit a Magnetic Plate
to each Door with a
Small 13mm Screw using
the shallow mark hole.
N b
H
G
Large 13mm Screw Small 13mm Screw
H
N b
H

J
Step 13
Fit the Doors and
Handles
The easiest way to
attach each Door is to fit
the top Hinge first, then
align and fit the other
Hinge.
a: Push the Hinge
onto the front part of the
Hinge Plate.
The recess at the bottom
of Screw B goes into the
slot in the Hinge Plate.
b: Keep the Hinge
FLAT against the Hinge
Plate as you slide it
across as far as it will go.
Tighten Screw A.
c: The Hinge must be
flat against the Hinge
Plate prior to any
adjustment.
d: The Hinge must NOT
BE AT AN ANGLE to the
Hinge Plate when
assembled.
This would indicate that
the recess at the bottom
of Screw B had not
located in the slot in the
Hinge Plate and the
Hinge would not be
secure.
Remove the Hinge from
the Hinge Plate and then
re-assemble being
careful to follow
instructions a-c.
e: Attach a Handle to
each Door using the
25mm Screws.
e:
Peel off the protective coating on the
panels and edging tape where present
a: b:
c: d:
L
M
L
L
B
L
M
M
M
A
M
L
B
E
E
J
8
7

Step 14
b:
c:
d:
a:
Adjust the doors if
needed
a: Before adjusting the
doors, use a spirit level
to check the base (or
top) of the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C.
A
A
B
C