Aqua One Oakstyle 110 User manual

Assembly Instructions
Please keep for future reference
Important - Please read these instructions fully before starting assembly
Oakstyle 110
Version 1 : 25/07/2017
ALR3413

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Make sure you have enough
space to layout the parts before
starting.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
Care and maintenance
Contact Us
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
Aqua Pacific UK Ltd.
Unit 10, Oriana Way
Nursling Industrial Estate
Southampton
SO16 0YU
Tel [phone]
Fax [phone]
[email protected]
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• Warning: This unit is heavy.
Please lift with care.
• Check you have all the
components and tools listed.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
Tools
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill
(do not use for
fitting screws)
Spirit
level
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: This unit must
be secured to a wall using the
overbalance protector kit
supplied.
• Dispose of all packaging
carefully and responsibly.

Panels
Please check you have all the panels listed below
6 7 Divider
(DF-00011563)
(64.5 x 33.3cm)
Wide Shelf (DF-00011554)
(33.55 x 33.2cm)
Left Side
(DF-00011541)
(75.5 x 35.7cm)
8Right Side
(DF-00011566)
(75.5 x 35.7cm)
10
9
11
Top (DF-00011560)
(69.5 x 41cm)
Base (DF-00011561)
(50.7 x 33.4cm)
Narrow Shelf (DF-00011564)
(15.45 x 33.2cm) x 3
12
Plinth (DF-00011562)
(50.7 x 9.5cm) x 2
13
1Drawer Front
(DF-00011548)
(34.2 x 16.2cm)
2Left Drawer
Side (W330-124LH)
(33 x 12.4cm)
3Right Drawer
Side (W330-124RH)
(33 x 12.4cm)
4Drawer Back
(W303-124)
(30.3 x 12.4cm)
5Drawer Base
(T314-327)
(31.4 x 32.7cm)
14 Fascia (F755-70)
(755 x 70mm) x 2
15 Door (F492-342LH)
(492 x 342mm)
16 Back (DF-00011568)
(75.5 x 39.6mm)

Fittings
Please check you have all the fittings listed below
A B
Large Metal Dowel (F901) x 18
C
D E
Knock-in Peg
(F171GY) x 4
Large Locking Cam
Nut (F900) x 22
Small Locking Cam
Nut (F900) x 2
H IG
Plastic Nail (F91) x 7
Wooden Dowel (F22) x 20
45mm Screw (F65) x 2
F
O
R
40mm Screw (F910) x 2
L
Wedgefix (F639) x 2
19mm Screw (F461) x 4
M
Shelf stud (F110) x 22
6 of these are required for Hood fixing.
See seperate instructions for fitting details.
*
J
9mm Screw (F74) x 2
K
9mm Screw (F73) x 4
N
P Q
S
Door Buffer (F137) x 4
Overbalance protector
kit (F474) x 1
Pre-mounted
hinge (F419) x 2
Handle (F287) x 2
Drawer runner (F1004) x 2
*
Quickfit dowel (F545) x 6

Step 1
Step 2
Step 3
Prepare the Drawer
Sides
Insert a Small Locking
Cam Nut into the Left
Drawer Side and the
Right Drawer Side.
Note: The arrow on the
Small Locking Cam Nut
must point towards the
hole in the edge of the
panel.
Attach the Drawer
Sides to the Drawer
Front
Push the Left Drawer
Side and Right Drawer
Side onto the back of the
Drawer Front.
Turn the Small Locking
Cam nuts on the Left
Drawer Side and right
Drawer Side.
Note: Turn the Small
Locking Cam nuts
clockwise to secure the
panels - more than 1/2 a
turn.
A
A
B
BBB
Prepare the Drawer
Front
Screw 2 Metal Dowels
into the Drawer Front.
Note: Tighten the Metal
Dowels up fully against
the panels.
Stick a Door Buffer into
the top right hand corner
and bottom right hand
corner of the Drawer
Front.
23
2
3
1
1
A
N
N
A

Step 4
Step 5
Step 8
Fit the Drawer Base
Slide the Drawer Base
down the grooves in the
Drawer Sides and down
into the groove in the
Drawer Front.
Fit the Drawer Back
Fit the Drawer Back
between the Drawer
Sides.
Make sure that the
Drawer Base fits into the
groove in the Drawer
Back.
Hold the Drawer Back
in position and tap the
Knock-in Pegs through
the holes in the Drawer
Sides.
Step 6
Attach the Handle
Attach a Handle to the
Drawer Front using two
19mm Screws.
Step 8
Step 7
Fit the Wedgefixes
Turn the drawer
assembly over and slide
2 Wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws.
C
C
C
C
D
D
D
2
3
2
4
5
5
3
1
I
I
O
1
The Drawer assembly
must be square before
fitting the wedgefixes.

R
R
R
F
F
Left Fascia - holes
nearest this side
Step 8
Step 9
Prepare the 2 Fascias
Check that the holes are
in the same place as the
diagrams, as one will be
the Left Fascia and one
will be the Right Fascia.
Tap a Wooden Dowel
into each of the 2
Fascias.
Note: Wooden Dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Prepare the Left Side
Tap 2 Wooden Dowels
into the Left Side.
Insert 5 Large Locking
Cam Nuts into the
Left Side.
Note: The arrow on the
Large Locking Cam Nuts
must point towards the
hole in the edge of the
panel.
Push 3 of the Quickfit
Dowels as far as they will
go into the Left Side.
Note: Only the plastic
thread of the Quickfit
Dowel sticks out from the
panel.
F
F
10mm
F
14
14
E
E
E
E
E
6
Right Fascia - holes
nearest this side
R
E

Step 10
Step 11
Finish preparing the
Left Side
a: Place a runner on the
Left Side as shown. Slide
back the top of Runner
and use the 2nd hole
from the front to fit the
first 9mm Screw.
b: Slide the Runner
back the other way and
fit the second 9mm
Screw into the
corresponding hole in the
Left Side.
Screw 4 metal dowels
into the Left Side.
6
6
AA
A
A
K
K
S
K
a:
b:
S
K
Fit the Left Fascia to
the Left Side
Push the Left Side down
onto the Left Fascia.
Use a screwdriver to
tighten the 3 Large
Locking Cam Nuts
fitted to the Left Side.
Note: Turn the Large
Locking Cam Nuts as far
as they will go - more
than 1/2 a turn.
Important: Make sure
there is no gap between
the fitted panels.
14
6
Dowel
this end

Step 12
Step 13
Fit the Right Fascia to
the Right Side
Push the Right Side
down onto Right Fascia.
Use a screwdriver to
tighten the 3 Large
Locking Cam Nuts
fitted to the Right Side.
Note: Turn the Large
Locking Cam Nuts as far
as they will go - more
than 1/2 a turn.
Important: Make sure
there is no gap between
the fitted panels.
Dowel
this end
7
14
Prepare the Right Side
Tap 2 Wooden Dowels
into the Right Side.
Insert 5 Large Locking
Cam Nuts into the
Right Side.
Push 3 of the Quickfit
Dowels as far as they will
go into the Right Side.
F
F
E
E
E
E
E
7
R
R
R

Step 14
Step 15
F
F
E
E
E
E
Prepare the Base
Tap 4 Wooden Dowels
into the Base.
Insert 4 Large Locking
Cam Nuts into the Base.
a:
Finished
front edge
10
F
F
A
A
A
A
7
Finish preparing the
Right Side
Screw 4 metal dowels
into the Right Side.

Step 16
F
F
E
E
Finished
front edge
K
K
S
Prepare the Divider
a: Place a Runner on
the Divider as shown.
Slide back the top of
Runner and use the 1st
hole from the front to fit
the first 9mm Screw.
b: Slide the Runner
back the other way and
fit the second 9mm
Screw into the
corresponding hole in
the Divider.
c: Tap 4 Wooden
Dowels into the Divider.
Insert 2 Large Locking
Cam Nuts into the
Divider.
K
S
F
F
a:
b:
c:
8
8
8
7
10
Finished
front edge
Fit the Base
Push the Base onto the
Right Side.
Use a screwdriver to
tighten the 2 Large
Locking Cam Nuts
fitted to the Base.
Step 17

Step 18
F
Fit the Divider
Push the Divider onto the
Base and fix it using
two 40mm screws.
Step 20
Fit the Plinths
Push the 2 Plinths onto
the Right Side.
Use a screwdriver to
tighten the Large Locking
Cam Nut fitted to each
Plinth.
10
8
F
E
E
F
F
E
E
Prepare the 2 Plinths
Tap 2 Wooden Dowels
into each of the Plinths.
Insert 2 Large Locking
Cam Nuts into each of
the Plinths.
Step 19
13
13
13
13
7
H
H

Prepare the Top
Screw 8 Metal Dowels
into the Top.
Fit the Bracket from the
Overbalance Protector
Kit to the shallow
mark-hole drilled into the
Top using 1 of its
Screws.
Note: Only fit 1 of the
Screws, the other 1 will
be fitted later.
Step 21
Packaging
piece
Packaging
piece
Packaging
piece
Step 23
Step 22
Raise the assembly
To make it easier to fit
the Top Panel, place
packaging pieces
underneath the Side
Panels to raise the
assembly.
Fit the Left Side
Push the Left Side onto
the Base and the Plinths.
Use a screwdriver to
tighten the 4 Large
Locking Cam Nuts
fitted to the Base and
Plinths.
13
10
13
6
A
A
A
A
A
A
A
A
9
Q
Q

Step 24
F
F
Fit the Top
Push the Top onto the
assembly.
Use a screwdriver to
tighten the 6 Large
Locking Cam Nuts fitted
to the Sides and Divider.
Step 26
Fit the Back
Push the Back onto the
Top.
Use a screwdriver to
tighten the 2 Large
Locking Cam Nuts fitted
to the Back.
Fix the Back to the Base
with two 45mm Screws.
Step 25
6
7
8
9
Prepare the Back
Tap 2 Wooden Dowels
into the Back.
Insert 2 Large Locking
Cam Nuts into the Back.
E
E
16
16
G
G
10
9

Step 27
Fit the plastic nails
Tap 2 Plastic Nails into
the bottom edge of each
of the Sides.
Tap a Plastic Nail into
the centre of the bottom
edge of the 2 Plinths and
the Back.
L
L
L
L
L
L
L

Step 28
a:
b: Q Q
Top
This unit must be fixed to a wall using
the Overbalance Protector Kit provided
Secure the unit to a
wall
a: Before fitting the unit
to a wall, use a spirit
level to check the top of
the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level.
To prevent possible
overbalancing this unit
must be secured to a
suitable wall by fitting the
Overbalance Protector
Kit to a wall.
b: Push the unit up
against the wall and slide
the Bracket against the
wall. Fit the 2nd Screw
from the kit into the
underside of the Top
panel.
Mark the slot at the back
of the Bracket for drilling
into the wall.
Wall fixings are not
supplied as they will need
to suit the wall type.
Take care when drilling
the wall that you do not
drill into any pipes, wires
etc. If in doubt, consult an
expert.
Q

Step 29
Step 30
Mx 4
Mx 4
Mx 4
12
12
12
Fit the 3 Narrow
Shelves
Insert 4 Shelf Studs for
each of the Shelves.
Lower the Narrow
Shelves down onto the
Shelf Studs.
Fit the Wide Shelf
Insert 4 Shelf Studs at
the required height.
Lower the Wide Shelf
down onto the Shelf
Studs.
Mx 4 11
The 6 Shelf Studs you have left are required for Hood fixing.
See seperate instructions for fitting details.
*

Step 31
Fit the Drawer
Slide both the Runners
forward and locate the
Drawer Sides between
them, lining up their
holes with the 2nd
'threaded' holes in the
Runners.
Working from the inside
of the Drawer, insert 2
9mm Screws through the
Drawer Sides and out
into the 2nd threaded
hole in the Runner.
Note: Do not overtighten
the Screws. If they catch
on the Runner you may
need to loosen them
slightly.
2nd threaded
hole
S
J
The Runners could have sharp
edges and we recommend that you
position them using a Screwdriver.
J
J
Prepare the Door
Push fit 2 Hinges into the
Door and secure it by
tightening up its 2
screws.
P
P
15
Step 32

Step 33
Step 34
Fit the Door and its
Handle
Line up the 2 screws in
the top Hinge with the 2
holes at the top of the
Left Side and push them
in.
Now push in the other
Hinge.
When both of the Hinges
have been pushed into
place, tighten their 2
screws.
Attach a Handle to the
Door using two 19mm
Screws.
Press the Screws into
the holes in the panel
When the Hinges have
been pushed in,
tighten up their Screws
PP
I
I
O
15
a:
b:
c:
Adjust the Door if
needed
a: Height adjustment.
Loosen Screws A on
Hinge Plates and move
Door up or down as
required.
Retighten Screw A.
b: Forward and Back
adjustment.
Loosen Screw B on
Hinge Plate and move
Door in or out as
required.
Retighten Screw B.
c: Sideways
adjustment.
To move Door ‘out’
loosen Screw C.
To move Door ‘in’ tighten
Screw C.
A
A
B
C

Step 35
15
Fit the Door Buffers
Stick a Door Buffer onto
the top and bottom
corner of the Door
where they will hit the
Divider.
N
N