Aqua One Styleline 51 User manual

Assembly Instructions
Please keep for future reference
Important - Please read these instructions fully before starting assembly
Styleline 51
Version 1 : 03/08/2017
ALR3418

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Make sure you have enough
space to layout the parts before
starting.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
Care and maintenance
Contact Us
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
Aqua Pacific UK Ltd.
Unit 10, Oriana Way
Nursling Industrial Estate
Southampton
SO16 0YU
Tel [phone]
Fax [phone]
[email protected]
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• Warning: This unit is heavy.
Please lift with care.
• Check you have all the
components and tools listed.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
Tools
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill
(do not use for
fitting screws)
Spirit
level
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: This unit must be
secured to a wall using the
overbalance protector kits
supplied.
• Dispose of all packaging
carefully and responsibly.

Panels
Please check you have all the panels listed below
1Left Side (DF-00012322)
(74.7 x 29.3cm)
2Right Side (DF-00012323)
(74.7 x 29.3cm)
3Top (DF-00012321)
(50.8 x 30.3cm)
4Base (DF-00012324)
(45.8 x 25.5cm)
9Door (DF-00012327)
(59.5 x 45.2cm)
8Back (DF-00012325)
(74.7 x 32.8cm)
5Shelf (DF-00012326)
(45.7 x 24.4cm) x 2
6Plinth (DF-00012328)
(45.8 x 6cm)
7Top Rail (DF-00012329)
(45.8 x 10.3cm)

Fittings
Please check you have all the fittings listed below
A B
Large Metal Dowel (F901) x 12
C
D E
Large Locking Cam
Nut (F900) x 12
H IG
45mm Screw (F65) x 2
F
Wooden Dowel (F22) x 16
J K
Overbalance Protector
Kit (F474) x 2
13mm Screw (F63) x 4
Hinge Plate
(F523) x 2 Hinge (F522) x 2
19mm Screw (F461) x 2
Plastic Nail (F91) x 6
Shelf stud (F110) x 8

C
C
C
C
Step 1
Step 2
Step 3
Prepare the Left Side
Tap 2 Wooden Dowels
into the Left Side.
Insert 2 Large Locking
Cam Nuts into the Left
Side.
Screw 3 Metal Dowels
into the Left Side.
Fit 2 hinge plates onto
the Left Side, making
sure that the slot is
facing towards the
finished front edge.
Prepare the Right Side
Tap 2 Wooden Dowels
into the Right Side.
Insert 2 Large Locking
Cam Nuts into the Right
Side.
Screw 3 Metal Dowels
into the Left Side.
H
B
10mm
C
Prepare the Base
Tap 4 Wooden Dowels
into the Base.
Insert 4 Large Locking
Cam Nuts into the Base.
B
H
H
A
B
A
A
Finished
Front Edge
1
B
B
A
A
A
Finished
Front Edge
2
C
B
C
B
C
B
C
B
4
Finished
Front Edge

C
Step 4
Step 8
Step 6
Fit the Base to the
Right Side
Push the Base onto the
Right Side.
Use a screwdriver to
tighten the 2 Large
Locking Cam Nuts
fitted to the Base.
Note: Turn the Large
Locking Cam Nuts as far
as they will go - more
than 1/2 a turn.
Step 5
Prepare the Top Rail
Tap 2 Wooden Dowels
into the Top Rail.
Insert 2 Large Locking
Cam Nuts into the Top
Rail.
A
B
2
4
2
B
C
B
Finished
Front Edge
Finished
Front Edge
Finished
Front Edge
Fit the Top Rail
Push the Top Rail onto
the Right Side.
Use a screwdriver to
tighten the Large Locking
Cam Nut fitted to the Top
rail.
Finished
Front Edge
7
7

C
C
Step 7
Step 8
Step 9
2
Prepare the Plinth
Tap 4 Wooden Dowels
into the Plinth.
C
C
6
6
7
4
Fit the Plinth
Push the Plinth onto the
Right Side.
Fit the Left Side
Push the Left Side onto
the assembly.
Use a screwdriver to
tighten the 3 Large
Locking Cam Nuts
fitted to the Base and
Top Rail.
1

Step 10
Step 8
Step 12
Step 11
A
A
A
A
A
Prepare the top
Screw 6 Metal Dowels
into the Top.
Fit the 2 Brackets from
the Overbalance
Protector Kits to the
shallow mark-holes
drilled into the Top
using 1 of their Screws.
Note: Only fit 1 of the
Screws, the other 1 will
be fitted later.
A
K
K
K
3
Packaging
piece
Packaging
piece
Packaging
piece
Raise the assembly
To make it easier to fit
the Top Panel, place
packaging pieces
underneath the Side
Panels to raise the
assembly.
Fit the Top
Push the Top onto the
assembly.
Use a screwdriver to
tighten the 4 Large
Locking Cam Nuts fitted
to the Sides.
3

Step 13
Step 15
Fit the Plastic Nails
Tap 2 Plastic Nails into
the bottom edge of each
of the Sides.
Tap a Plastic Nail into
the centre of the bottom
edge of the Plinth and
the Back.
Step 14
G
GG
G
G
G
C
C
Prepare the Back
Tap 2 Wooden Dowels
into the Back.
Insert 2 Large Locking
Cam Nuts into the Back.
B
B
8
Fit the Back
Push the Back onto the
Top.
Use a screwdriver to
tighten the 2 Large
Locking Cam Nuts fitted
to the Back.
Fix the Back to the Base
with two 45mm Screws.
8
D
D

Step 16
a:
b: K K
Top
This unit must be fixed to a wall using the
2 Overbalance Protector Kits provided
Secure the unit to a
wall
a: Before fitting the unit
to a wall, use a spirit
level to check the top of
the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level.
To prevent possible
overbalancing this unit
must be secured to a
suitable wall by fitting the
2 Overbalance Protector
Kits to a wall.
b: Push the unit up
against the wall and slide
the Brackets against the
wall. Fit the 2nd Screw
from the kits into the
underside of the Top
panel.
Mark the slot at the back
of the Brackets for drilling
into the wall.
Wall fixings are not
supplied as they will need
to suit the wall type.
Take care when drilling
the wall that you do not
drill into any pipes, wires
etc. If in doubt, consult an
expert.
K
K

Step 17
Step 19
Prepare the Door
Push fit the 2 Hinges into
the Door and secure
them using the 13mm
Screws.
Step 18
I
F
F
I
F
F
Jx 4
Jx 4
Fit the Shelf Studs
Insert 4 Shelf Studs for
each of the 2 Shelves, at
the required height.
Fit the 2 Shelves
Lower the Narrow
Shelves down onto the
Shelf Studs.
5
5
9

E
E
L
9
e:
Step 20
Fit the Door and Handle
Note: The easiest way to
attach the Door is to fit
the top Hinge first, then
align and fit the other
Hinge.
a: Push the Hinge
onto the front part of the
Hinge Plate.
The recess at the bottom
of screw B goes into the
slot in the Hinge Plate.
b: Keep the Hinge
FLAT against the Hinge
Plate as you slide it
across as far as it will go.
Tighten screw A.
c: The Hinge must be
flat against the Hinge
Plate prior to any
adjustment.
d: The Hinge must NOT
be AT AN ANGLE to the
Hinge Plate when
assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
Hinge Plate and the
Hinge would not be
secure.
Remove the Hinge from
the Hinge Plate and then
re-assemble being
careful to follow
instructions a-c.
e: Attach the Handle to
the Door using two
19mm Screws.
a: b:
c: d:
I
N
I
I
B
I
N
N
N
A
N
I
B

Step 21
b:
c:
d:
a:
Adjust the Door if
needed
a: Before adjusting the
Door, use a spirit level to
check the Top (or Base)
of the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the
Hinges, as shown.
b: Height adjustment.
Loosen screws A on
Hinge Plates and move
Door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on
Hinge Plate and move
Door in or out as
required.
Retighten screw B.
d: Sideways
adjustment.
To move Door ‘out’
loosen screw C.
To move Door ‘in’ tighten
screw C.
A
A
B
C