Argos 240/9922 User manual

One Drawer Nesting Table
Dimensions
Width - 48cm
Depth - 40cm
Height - 55cm
Issue 1 - 26/03/14
Important –Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Assembly Instructions- Please keep for future reference 240/9922

Safety and Care Advice
Important– Please read these instructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
pages 2 and 3.
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance
1

Components - Panels
Please check you have all the panels listed below
2
Left side panel
Big Table
Small Table
(534 x 370mm)
1
Top panel (480 x 400mm)5
Side panel x 2
(335 x 302mm)
Back panel
(370 x 170mm)
3
Cross rail x 2
(404 x 80mm)
4
Right side panel
(534 x 370mm)
2
Left drawer side panel
(300 x 125mm)
6
Drawer base
(335 x 298mm)
9
Right drawer side panel
(300 x 125mm)
7
Drawer back panel
(325 x 125mm)
8Drawer front
(364 x 167mm)
10
Front and rear panel x 2
(230 x 60mm)
12 Top panel
(340 x 340mm)
13
11

3
12mm Screw x 12
Ruler- Use this ruler to help correctly identifythescrews
Tools required
A
Runner outer piece x 2Runner inner piece x 2
Bolt x 1
E
Metal dowel x 30 Small wood dowel x 9
B
H
C
I
Note:The quantities beloware the correct amount to complete the assembly. In some cases more
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
110 115 120 125 130 135 140 145 150 155 160 165 170
105
F
35mm Screw x 4
D
K
Large metal
cam x 26
Small metal
cam x 4
Handle x 1
G
J
Components - FittingsIf you have damaged or missing components,
call the Customer Helpline: 08456 400800
Large wood dowel x 8
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)

Position Runner outer
piece onto Right side
panel and fix through
the indicated holes
shown using Screws .
4
Assembly Instructions
Step 1
Dis-assemble Runners
A
B
B
C
C
C
2
2
Step 2
Attaching Runner
outer piece on Side
panel
Note: Rubber tube
on the Runner outer
piece should face to
the rear leg which has 3
holes as shown.
Rubber tube
face to the
rear leg which
has 3 holes
as shown.
B
B
Big Table.
To disassemble the
runners pull out the inner
piece of runners, to
seperate the Inner piece
and the Outer piece
, push and hold the
tab and then pull
completely out as shown.
A
B

5
Assembly Instructions
D
D
D
Note: Insert metal
dowels as far as shown.
Do not over tighten.
Repeat Step 2 and
Step 3 on Left side
panel .
as shown.
Screw metal dowels
Turn the Right side panel
upside down.
Firmly push Back panel
and Cross rails
onto Right side panel
, make sure the
Wood and metal dowels
enter corresponding
holes.
into Right side panel
2
2
2
2
2
4
4
4
3
3
1
Firmly push Small wood
dowels into indicated
holes.
Step 3
Step 4
D
Note: Tighten all cams
in this way.
Note: Longer
leg of the cross
on the Metal
Cams must face towards
end of panel (as shown).
Then, using a Philips
Screwdriver, screw all
Metal Cams clockwise
until they are ‘hand tight’.
F
Long leg.
Taped edge
face upwards.
E
F
E
Insert Large metal cams
into the holes on
Back panel and the rails
so that they are flush.
F

Firmly push Left side
panel onto Back
panel and Cross
rails , make sure the
wood and metal dowels
enter corresponding
holes.
Secure with Metal cams
.
4
4
5
5
5
4
1
1
3
3
Assembly Instructions
6
Step 6
Step 5
D
D
as shown.
Screw metal dowels
into Top panel 5
Firmly push Small wood
dowels into indicated
holes.
E
E
Lay the big table Top
panel upside down
on a soft surface.
Firmly push Large wood
dowels into indicated
holes in Top panel.
G
G
FF
F
F

7
Assembly Instructions
Step 7
Position Runner inner
piece onto Drawer
side panels and
fix through the indicated
holes shown using
Screws .
A
C
6
6
7
7
Step 8
Note: Make sure the
front end of Runner is
flush with the front edge
of drawer side as shown.
Make sure the front end
of Runner is flush with
the front edge of drawer
side.
C
Firmly push the
assembled piece from
Step 5 onto Top panel
, make sure the
wood and metal dowels
enter corresponding
holes.
Secure with Metal cams
.
5
5
F
F

on back of Drawer front
.
Assembly Instructions
8
Step 9
dowels into holes
10
10
c: Screw Metal
D
D
6
6
8
9
9
8
7
Secure with Small metal
cams .
I
I
Position drawer front
against end of drawer
sides and firmly push to
make sure the Drawer
base enters the groove in
Drawer front.
into the grooves as
shown.
Drawer assembly
a: Fix drawer sides
to Drawer back panel
using screws .
H
H
b: Slide Drawer base
d:
the Drawer front using
Bolt .
Attach Handle to
e:
Foiled side
face upwards.
JJ
K
K
10
7

into Small table side
panel as shown.
11
11
9
Slide Drawer into the
space as shown, make
sure the Runner inner
piece enters the Runner
outer piece on both
side.
Assembly Instructions
Step
Step
10
Taped edges
face upwards.
D
D
Screw metal dowels
Firmly push Small wood
dowels into indicated
holes.
E
E
Firmly push Side panels
onto Front and rear
panels , make sure the
wood and metal dowels
enter corresponding
holes.
Secure with Metal
cams .
F
F
11
Step 12
11
12
12
11
12
11
Small Table.