Argos Shelby 322/0296 User manual

Shelby - Cabin Bed
Dimensions
Width - 195cm
Depth - 95.5cm
Height - 53cm
Issue 1 - 9/02/10
Important – Please read these instructions fully before starting assembly
Assembly Instructions - Please keep for future reference
338/9663
322/0296
If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6400800

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
pages 2, 3 and 4.
• Remove all ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your oor.
• Parts of the assembly will be
easier with 2 people.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and ttings are
tightend properly.
Handy Hints
• WARNING: Do not place this child`s bed near heat
sources, windows and other furniture.
• WARNING: Do not use this child`s bed if any part is
broken, torn or missing.
• WARNING: Not suitable for children under the age of
4 years.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
Front bed board (192 x 39.45cm)
3
Right side panel (95.5 x 53cm)
2
Left side panel (95.5 x 53cm)
1
Front/Back bed supports x2 (192 x 14.3cm)
5
Back bed board (192 x 56.05cm)
4
Right central support (32 x 37.2cm)
6
Right bottom panel (32 x 37.2cm)
8Left bottom panel (63 x 37.2cm) 9
Left central support (63 x 37.2cm)
7
If you have damaged or missing components,
call the Customer Helpline: 0345 6400800

3
Components - Panels
Please check you have all the panels listed below
Middle crossbar (94 x 12cm)
10
Front crossbar (94 x 10cm)
12
Left shelf partition (94 x 37.2cm)
13
Shelf (32 x 37.2cm)
15
Front board (192 x 4cm)
17
Drawer front x2 (96.9 x 16cm)
16
Right shelf partition (94 x 37.2cm)
14
Drawer sides x2 (159.5 x 12cm)
18
Drawer bottom panel x2 (90.3 x 33.9cm)
19
Back crossbar (94 x 10cm)
11
If you have damaged or missing components,
call the Customer Helpline: 0345 6400800

Please check you have all the ttings listed below
50mm wood screw x 20
Ruler - Use this ruler to help correctly identify the screws
Tools required
A
Screw-in dowel x 4
E
50mm xing screw x 31
B
16mm wood screw x 38
H
30mm wooden dowel x 14
C
13mm xing screw x 12
I
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
100 20 30 40 50 60 70 80 90 100
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Plastic support x 4
F
Locking nut x 4
D
Left inside runner x 2
Plastic support x 7
K
Allen key x 1
O
M N
Right outside runner x 2
L
Shelf support x 4
G
Left outside runner x 2
Right inside runner x 2
J
Components - Fittings
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Eye protection
(when using a
hammer)
4
The screws length is measured from the head to the point (30mm screw shown).
Drill

Assembly Instructions
Step 1
Step 2
Attaching runners
Position runners J2mm
in from front edge of the
left shelf partition 13 and
runners L2mm in from
front edge of the right
shelf partition 14 .
Fix through holes shown
using 13mm xing
screws I.
Insert the 30mm dowels
Cinto left shelf partition
13 and into right shelf
partition 14 .
Assemble middle
module
Screw the left shelf
partition 13 and the right
shelf partition 14 to the
middle crossbar 10 , to
the back crossbar 11
and to the front crossbar
12 through 50mm xing
screws B.
Note: Use the Allen Key
O.
5
I
I
I
I
II
I
I
I
I
II
J
J
L
L
C
C
C
C
C
C
B
B
B
B
B
B
J
I I I 13
13
14
13
14
12
11
10
Clockwise
B
O
2mm
Front edge
Front edge
Front edge

6
Assembly Instructions
Attaching panels
a: Insert the 30mm
dowels Cinto left shelf
partition 13 and into right
shelf partition 14 .
Position left central
support 7to left bottom
panel 9and right
central support 6to
right bottom panel 8.
Fix the panels through
50mm xing screw B.
Note: Use the Allen Key
O.
b: Position the attached
panels: left central
support 7and left
bottom panel 9and
right central support 6
and right bottom panel
8like shown on the
picture.
Fix the panels to left shelf
partition 13 and to right
shelf partition 14 through
50mm xing screws B.
Note: Use the Allen Key
O.
Step 3
b:
a:
C
C
C
C
B
B
B
B
B
B
B
7
7
9
9
13
13
14
14
6
6
8
8
Clockwise
B
O
Clockwise
B
O

Assembly Instructions
Attaching panels
a: Insert the 30mm
dowels Cinto left side
panel 1and into right
side panel 2.
b: Position the left
side panel 1and the
right side panel 2like
shown on the picture and
x them to left central
support 7, left bottom
panel 9, right central
support 6and right
bottom panel 9through
50mm wood screws A.
Note: Use the Allen Key
O.
Step 4
b:
a:
A
A
A
A
C
C
C
C
1
2
1
7
9
6
8
2
7
A
O

Assembly Instructions
Attaching panel
a: Screw plastic
supports Nto the front
board 17 through 16mm
wood screws H.
First rotate the construction
of the bed horizontally
at 180 degrees and then
vertically at 90 degrees like
shown on the pictures.
b: Position the front
board 17 and screw it to
left central support 9
, middle crossbar 12
and right central support
8through 16mm wood
screws H.
Step 5
b:
a:
H
H
H
H
H
H
H
N
N
N
N
N
N
N
N
H
H
H
H
H
H
H
H
17
17
8
12
9
17
8
180
90

Assembly Instructions
Attaching panels
Two people are needed
here
a: Position the front bed
board 3and the back
bed bord 4 and x them
to left shelf partition 13
and right shelf partition
14 through 50mm xing
screws B.
Note: Use the Allen Key
O.
b: Fix the left side panel
1and the right side
panel 2to the front bed
board 3and the back
bed board 4through
50mm wood screws A.
Note: Use the Allen Key
O.
Step 6
b:
a:
9
A
AA
A
A
AA
A
B
B
B
B
B
BB
B
4
3
14
13
1
3
4
Clockwise
B
O
A
O