Argos Aston Chair User manual

Aston Chair
Assembly Instructions - Please keep for future reference 603/5213
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 17/04/12
Dimensions
Width - 43cm
Depth - 52cm
Height - 85.5cm
603/5189
603/5196
603/5237
603/5172
603/5206
603/5220
603/3796
603/3806

1
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warnings
Care and maintenance
• We suggest you spend a short
time reading through this leaflet
and follow the simple step by
step assembly instructions.
• Do not discard any of the
packaging until you have
checked that you have all the
parts and the pack of fittings.
• Assemble this product on a flat
surface.
• Assemble all parts loosely
before tightening any bolts.
• Discard all extra fittings and
keep fittings out of reach of
children.
• Unit weight: 5kgs.
• Retain Assembly Instructions
for future reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• This product should only be
used on firm, level ground.
• Make sure the legs remain in
contact with the ground.
• Do not stand on the product.
• Please clean the table surface
using either damp (not wet)
cloth and a mild domestic soap
solution or by using an
appropriate polish.
• Do not use any abrasive
materials when cleaning.
• From time to time check that
there are no loose bolts on this
unit.

2
Components - Parts
Components - Fittings
Please check you have all the parts listed below
Please check you have all the fittings listed below
M8 x 50mm Bolt x 1
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Backrest
(34.5 x 85.5 x 10cm)
1Front leg x 2
(43 x 4 x 3.2cm)
3Seat
(43 x 41.5 x 11.5cm)
2
Ruler - Use this ruler to help correctly identify the screws
0 15 30 45 60 75 905 20 35 50 65 80 9510 25 40 55 70 85 100 120 140105 125 145110 130 150115 135 155 160 165 170
M8 x 60mm Bolt x 4
Washer x 9
M8 x 80mm Bolt x 4
A B C
D
Allen key x 1
E

3
Assembly Instructions
Place the backrest on a
flat protected surface.
Position the seat on
the backrest as
shown and fix using bolts
& and washers .
Tighten the bolts using
allen key .
Step 1
Step 2
Attaching legs
Place the seat upside
down on a flat protected
surface.
Peel off bottom cloth
cover of seat to be able to
secure the legs. Pull the
cloth from the back side of
the seat.
Insert the legs into the
holes of the seat as
shown and fix using bolts
and washers .
2
3
1
2
B
E
D
A C D
Attaching backrest
Important:
Do not fully
tighten bolts at
this stage.
B
D
D
D
D
D
B
B
D
D
B
B
3
3
3
2
2
C
D
A
D
A
B
C
D
2
1
1
B
A
A
D
D
1
2
B
B
A
D
D
A
2
Cloth
cover

4
Step 3
Step 4
Aligning the legs
Carefully turn over the
chair and place on a flat
surface.
Tighten all the bolts on the
legs using allen key while
making adjustments to
ensure the legs are even
on the floor.
Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Cloth cover
Assembly is complete.
Re-attaching the
bottom cloth cover
Re-attach the bottom
cloth cover as shown and
fasten with the magic
tape.
Carefully turn over the
chair.
Carefully
turn over
3
3