Argos 248/6622D User manual

Ashley Multifunction Storage Unit
Dimensions
Width - 60cm
Depth - 30cm
Height - 76cm
Issue 1 - 26/03/14
Important –Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Assembly Instructions- Please keep for future reference 248/6622D

Safety and Care Advice
Important– Please read these instructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
pages 2 and 3.
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance
1

Components - Panels
Please check you have all the panels listed below
2
Upper shelf (568 x 296mm)
1Lower divider
(321 x 296mm)
3
Upper divider
(180 x 296mm)
8Left side
(745 x 296mm)
6Right side
(745 x 296mm)
7
5
Bottom shelf (568 x 296mm)
4
Top panel (600 x 298mm)
9
Lower shelf (568 x 296mm)
2
Adjustable
shelf
(238 x 296mm)
10 Small drawer
back
(347 x 175mm)
11
Large drawer back
(541 x 175mm)
16
Drawer left
side x 2
(251 x 177mm)
12 Drawer right
side x 2
(251 x 177mm)
13
Small drawer
front
(372 x 177mm)
15
Top and Bottom back panel
x 2
(208 x 597mm)
19
Large drawer front
(566 x 178mm)
18
Small drawer
base
(356 x 247mm)
14
Drawer Rail
(238 x 40mm)
Large drawer base
(550 x 247mm)
17
Middle back panel
(348 x 597mm)
20

3
Large metal dowel x 24
Ruler- Use this ruler to help correctly identifythescrews
Tools required
A
14mm Screw x 3
25mm Screw x 2 Cover x 8
E
Wood dowel x 24
B
H
C
I
Note:The quantities beloware the correct amount to complete the assembly. In some cases more
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
110 115 120 125 130 135 140 145 150 155 160 165 170
105
Drawer stop x 3
F
Wall plug (for solid walls only) x 2
35mm Screw x 11
D
Nail x 22
K
Large metal
cam x 24
M
Small metal
cam x 9
N
L
Small metal dowel x 9
Shelf pin x 4
G
J
Components - FittingsIf you have damaged or missing components,
call the Customer Helpline: 08456 400800
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Drill
7mm Suitable drill bit
(for use with wall plug)
Eye protection
(when using a
hammer)
Wall strap x 2

Position Upper and
Lower shelves
onto the Lower Divider
as shown, make sure
Metal and Wooden
dowels enter
corresponding holes.
Shelves as shown.
4
Assembly Instructions
Step 1
Fitting dowels
Screw metal dowels A
A
C
into Upper and Lower
1
1
1
2
1
3
2
2
2
3
Note: Insert metal
dowels as far as shown.
Do not over tighten.
Firmly push wooden
dowels into indicated
holes.
B
Step 2
A
Attaching panels
Insert 4 Metal Cams
into the 4 holes on
Lower divider so that
they are flush.
Note: Tighten all cams
in this way.
Note: Longer
leg of the cross
on the Metal
Cams must face towards
end of panel (as shown).
Then, using a Philips
Screwdriver, screw all
Metal Cams clockwise
until they are ‘hand tight’.
C
C
Long leg
C
Holes for shelf
Taped edge
B
A
B