Argos Stirling User manual

MADE IN
BRITAIN
Dimensions
Stirling - 2 Drawer 3 Door Mirrored Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 11/11/14
Important - Please read these instructions fully before starting assembly
ALR3107
339/3130
330/9409
Width - 106.5cm
Depth - 49cm
Height - 189cm
Can you change the title to include the mirror please.
Also the mirror door needs including on the AI.
Components
V should be x4 handles
G should be x4 screws
Step 4+5 – Remove the word large from drawer assembly.
Step 25 – Hinges are O
Glass warning to be added to Ai.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 74kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.
Drawer Front (D3026A)
(510 x 245mm) x 2
Drawer Back (W457-195)
(457 x 195mm) x 2
Left Drawer Side (W370-195LH)
(370 x 195mm) x 2
Drawer Base (T468-367)
(468 x 367mm) x 2
Right Drawer Side (W370-195RH)
(370 x 195mm) x 2
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
1 2 3
4
5
Tools required
Rule
Square
Spirit level
Scissors
Bradawl
Hammer
Cross-head screwdriver
Step ladder
Eye protection
(when using a
hammer or drill)
Electric drill
(do not use for
fitting screws)

Components - Panels
Please check you have all the panels listed below
2
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Upright (D3022A)
(1549.5 x 453mm)
Small Back Rail (D3027A)
(330 x 123mm)
Top (D3021A)
(1063 x 490mm)
Base (D3023B)
(106.5 x 490mm)
Horizontal (D3024A)
(1004 x 456mm)
Small Back (X1836-349)
(1836 x 349mm)
Large Back (X1836-677)
(1836 x 677mm)
Left Side (D3016A)
(1810 x 457mm)
Right Side (D3017A)
(1810 x 457mm)
6
17
7
2019
14
Small Hanging
Rail (FHR322)
(322mm long)
15
Large Hanging
Rail (FHR651)
(651mm long)
16
Door (D3019A)
(1553 x 339mm) x 2
18
Large Back Rail (D3020A)
(659 x 123mm)
13
8
9
10
11
Divider (D3025A)
(245.5 x 452mm)
12
Mirror Door (D3019MA)
(1553 x 339mm)
(Mirror - SG28
1513 x 301mm
Safety Back SAR)

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110
A B
Metal dowel (F901) x 8
C
D E F
G
J K
NM
L
O
Knock-in Peg (F171GY) x 8
H
9mm Screw (F73) x 8
38mm Screw (F81) x 4 13mm Screw (F63) x 22
P
Drawer runner (F1004) x 4
9mm Screw (F74) x 4
Q
R
40mm Screw (F910) x 23
S
Wooden dowel (F22) x 2 Small locking nut
(F3) x 4
T
U
Rail holder
(F1014) x 4
V
Hinge plate (F523) x 9 Hinge (F518) x 9
Large locking
nut (F900) x 6
Double metal dowel (F566) x 1 Nail screw (F277) x 5 Back holder (F276) x 5
*These can also be round
Wedgefix (F639) x 4
Handle (F463) x 4
Large wooden dowel (F40) x 1
Nail x (F51) x 38
I
WStrap Screw Washer x 2
Overbalance protector kit (F269) x 1
Foot (F340) x 5

1
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
B
B
B
C
C
CC
23
Step 2
Prepare the 2 drawer
fronts
Screw 2 metal dowels
into each of the drawer
fronts .
Note: Tighten the metal
dowels up fully against
the panels.
B
1
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
C
2
3
Attach the drawer
sides to the drawer
fronts
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
2
3
1
C
C
3
2
B
B
1
2
3
x 2
x 2 x 2
x 2

1
Assembly Instructions
5
Step 4
L
L
Fit the drawer bases
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
5
2 3
1
4
2 3
5
4
4
L
5
L
L
Attach the handles
Attach a handle to
each drawer front
using screw .
V
G
Step 6
1
2
3
2 3
4
2
3
5
Step 7
Fit the wedgefixes
Turn the 2 drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
Q
Q
Q
Q
x 2
x 2
x 2
x 2
G
V
1

Finished
front edge
Assembly Instructions
6
Step 8
N
Finished
front edge
J
P
Prepare the left side
a: Fit 3 hinge plates
to the left side
making sure that the slot
is facing towards the
finished front edge.
Push a rail holder into
the left side . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
Place a runner onto
the left side . Slide
back the top of runner
and use the 2nd hole
from the front to fit the
1st screw .
Screw a metal dowel
into the left side .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .
N
6
U
6
P
6
J
P
J
6
a:
b:
H
B
6
U
H
N
N
N
B
J
P
J
6
6
Finished
front edge

Assembly Instructions
7
Step 9
Finished
front edge
J
P
Prepare the right side
a: Fit 3 hinge plates
to the right side
making sure that the slot
is facing towards the
finished front edge.
Push a rail holder into
the right side . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
Place a runner onto
the right side . Slide
back the top of runner
and use the 2nd hole
from the front to fit the
1st screw .
Screw a metal dowel
into the right side .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the right side .
N
7
U
7
P
7
J
P
J
7
7
b:
a:
H
B
U
H
N
N
N
B
J
P
N
7
7
J
Finished
front edge
Finished
front edge

Assembly Instructions
8
Step 10
Polystyrene
block
Polystyrene
block
E
E
E
E
Fit the top to the sides
Attach the top to the
left side and right
side using 4 screws
. .
Note: To make it easier
to fit the top and base
panels, place
polystyrene blocks from
the packaging
underneath the side
panels to raise the
assembly.
9
6
7
E
Polystyrene
block
Polystyrene
block
Step 11
Finished
top edge
A
Prepare the small
back rail
Insert 2 large locking
nuts into the small
back rail .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Tap a wooden dowel
into the small back rail
. .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
13
F
A
13
F
F
F
Plain chipboard
surface
13
9
10mm
A
6
7

Assembly Instructions
9
Step 12
U
H
N
N
N
Finished
front edge
U
H
Prepare the upright
a: Fit 3 hinge plates
to the upright making
sure that the slot is
facing towards the
finished front edge.
Push a rail holder into
the upright . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
Turn the upright over
b: Push a rail holder
into the upright .
Make sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
U
8
H
U
8
H
N
N
8
Turn the
upright over
8
8
b:
a:
Finished
front edge