Argos 906/4638 User manual

MADE IN
BRITAIN
Dimensions
Width - 54.5cm
Depth - 33cm
Height - 65cm
3 Basket 2 Shelf Unit
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 02/07/12
Important - Please read these instructions fully before starting assembly
ALR2773
906/4638
Issue 2 - 02/07/12 - Shelf size changed to 238 x 310mm and Back size changed to 493 x 597mm.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 13kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
Please check you have all the panels listed below
2
1
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Left Side (D1469A)
(597 x 328mm)
4
2 3
Right Side (D1470A)
(597 x 328mm)
Top/Base (D1468A)
(545 x 329mm) x 2
5
6
Divider (D1472A)
(597 x 312mm)
These 2 holes are on
the opposite surface
Shelf (D1471A)
(238 x 310mm) x 3 Back (D1775A)
(493 x 597mm)

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
B
Metal dowel (F901) x 12
C
D
Large locking
nut (F900) x 12
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
see malibu fitment mk2 for large number of panels and fittings
F
Feet (F854) x 4
E
25mm Screw (F50) x 4
G
Shelf support (F121) x 12
45mm Screw (F65) x 3
A
Wooden dowel (F22) x 4

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Prepare the left side
Insert 4 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 1
CC
C
C
C
C
1
Step 2
Prepare the right side
Insert 4 large locking
nuts into the right
side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
C
2
Step 3
Prepare the divider
Insert 4 large locking
nuts into the divider
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
C
3
1
Note: The left side only has
holes on the surface shown.
Note: The divider has holes
on both surfaces.
Note: The right side only has
holes on the surface shown.
C
C
C
C
C
C
C
C
C
C
C
C
1
2
3
Left Side (D1469A)
(597 x 328mm)
Right Side (D1470A)
(597 x 328mm)
Upright (D1472A)
(597 x 312mm)

Assembly Instructions
5
Step 4
Finished
front edge
Prepare the base
a: Screw the 4 feet
onto the base using
screws .
Note: The feet must be
fitted close to the edges
of the base for maximum
stability, as shown.
Turn the base over
b: Screw 6 metal dowels
. into the base .
Note: Tighten the metal
dowels up fully against
the panels.
B4
4
4
Finished
front edge
BB
B
B
B
B
B
4
Finished
front edge Finished
front edge
Step 5
Join the right side and
top
Push the right side
onto the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the right side .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
2
4
C
C
2
4
2
Note: The right side only has
holes on the surface shown.
E
F
F
F
F
Turn the base over
a:
b:
F
E

Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
6
Step 5
Finished
front edge
Fit the divider
Push the divider onto
the base .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the divider .
Step 8
4
3
3
4
C
3
Fit the left side
Push the left side
onto the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the divider .
Step 6
1
4
C
3
1
4
Join the right side and
base
Push the right side
onto the base .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the right side .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
2
4
C
2
Note: The right side only has
holes on the surface shown.
2
4
3
Note: The divider has holes
on both surfaces.
B
C

Assembly Instructions
7
Step 7
Step 8
Prepare the back
Tap 4 wooden dowels
into the back .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Finished
front edge
41
Fit the left side
Push the left side
onto the base .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the left side .
1
4
C
1
A
A
A
A
10mm
A
A
6
6

Assembly Instructions
8
Step 9
Step 10
Fit the back
Position the back
between the left side
and right side and
gently push in its
wooden dowels .
1
1
6
1
26
2
Prepare the top
Screw 6 metal dowels
into the top .
B
4
Finished
front edge
B
B
B
B
B
B
4
Step 9 Should be fit the back, and should read put the back (6) between l-h & r-h gently push in the wooden dowels
A
2 holes
1 hole

Assembly Instructions
9
Step 11
Fit the top
Lower the top down
onto the assembly.
Use a screwdriver to
tighten the 6 large
locking nuts fitted to
the left side , right
side and upright .
4
4
C
1
2 3
1
2
3
Gx 4
Gx 4
Fit the shelf studs
For each of the 3
shelves , insert 4 shelf
studs .
Make sure that the plastic
sleeve is fully pushed
onto the shelf stud.
G
Gx 4
Step 12
5
G
Finished
front edge