Argos Canterbury 4 DR 6 DRW ROBE User manual

max.
lbs
kg25
55
lbs
kg30
66
lbs
kg20
44
lbs
kg9
39
lbs
kg8
18
Canterbury 4 DR 6 DRW ROBE
Assembly Instructions - Please keep for future reference 499/2420
481/5806
501/7067
Dimensions
Width - 201.3cm
Depth - 62.7cm
Height - 202.1cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
71940 Version C Date 14/06/2016

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to lay out the parts before
starting.
• During assembly, do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the use
of power drivers for
inserting screws, as
this could damage
the unit. Only use hand screw
drivers.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
• The provided tip-over restraint
must be installed in order to
optimize user safety.
Safety

D 00486 Left drawer side
(43.5 x 14cm) x6
H 00487 Right drawer side
(43.5 x 14cm) x6
J 02748 Drawer back
(42.1 x 14cm) x4
K 02751 Drawer back
(90.6 x 14 cm) x2
P 06293 Large
drawer bottom
(91.8 x 43.3cm) x2
O 06294 Small
drawer bottom
(43.3 x 43.3cm) x4
L 09790 Back panel (201.5 x 48.9cm) x2
M 09791 Back panel (201.5 x 96.9cm)
N 18732 Frame door (146.9 x 48.2cm) x4
76427 Profile side (62 x 2.5cm) x2 76428Profile side
(62 x 2.5cm) x2
76460 Profile front (200.5 x 4cm) x2
E
Drawer front
(48.2 x 22.1cm) x4
FA Side panel L/R (198.8 x 58cm) x2
UB
Large fixed shelf
(95.5 x 57.9cm) x2
GB Divider panel (198.8 x 58cm) x2
T
Loose shelf
(46.9 x 57.9cm) x4
UC
Small fixed shelf
(47 x 57.9cm) x4
EA
Drawer front
(96.7 x 22.1cm) x2
ID Bottom / Top panel (201.3 x 62.4cm) x2
A C B
Components - Panels
Please check you have all the panels listed below
2
If you have damaged or missing components, call the
Customer Helpline: Argos = 0345 6400800

3
Please check you have all the fittings listed below
Holder x2
Nail x4
Bracket x24Shelf support x16
Connector bolt
(ø7 x 50mm) x24 Flat head screw
(ø5.8 x 9mm) x24
Flat head screw
(ø3.5 x 15mm) x12 Screw (ø4 x 13mm) x6
Flat head screw
(ø3 x 12mm) x2
Screw (ø5 x 7.5mm) x24
Big nail x36
Drawer support x12
Flat head screw
(ø6.3 x 27mm) x22
Floor glider x8
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Allen key x1
Drawer runner x12
Drawer fastener x24
Dowel (ø5 x 30mm) x16
Machine screw
(M4 x 7mm) x12 Machine screw
(M4 x 15) x24 Machine screw
(M4 x 23mm) x12
Hinge x12
Wedges x4
Cam x12
Cam bolt x12
Hinge plate x12
Screw (ø7 x 8mm) x24
Handle x12
Drawer bottom support x2
Stop x8
Hanger x1
Components - Fittings
Ruler - Use this ruler to help correctly identify the screws
Tools required
10601 11011
20228
25233 25440
26020
1122911042
11230
23010
20203 23006
25215
25610 26033 26071
31513
31687
26211 26221 26232
33204 50491
96203
97642
41434 72509
63008 94009
81040
10511
52291
25 pcs
Strap x2
Cross head screwdriver
(medium & large) Wooden block
Books X6
Tape measure
Flathead screwdriver
(medium)
Ruler
Eye protection
(when using a
hammer or glue)
01 02 03 04 05 06 07 08 09 0 100 110 120 130 140 150
01 23 45 6
Hammer

GB
(x2)
FA
(x2)
GB
GB
4
Assembly Instructions
Step 1
Step 2
Insert dowles
Insert dowels 20203
into outer holes on the
ends of side panel FA
and GB .
Attaching hanger holder
Attach holder 10601 with
flat head screw 25215 on
divide panel GB x2.
Dowel
# 20203 X16
Fittings you will need for this step:
Fittings you will need for this step:
Flat head screw
# 25215 X2 Holder # 10601 X2

1
FA GB
30
GB
31
FA
10
11
31
32
10
11
1
5
Assembly Instructions
Step 3
Attaching hinge plate
Fixing each hingplate
50491 with screw
2x 26071 .
Insert machine screw
26211 in center of
hinge plate.
Fittings you will need for this step:
Screw
# 26071 X24 Machine screw # 26211 X12 Hinge plate # 50491 X12

z
GB
1
GB
8
FA
1
FA
8
Assembly Instructions
6
Step 4
Step 5
Fittings you will need for this step:
Fittings you will need for this step:
Screw
# 11230 X16
Screw
# 11230 X8
Attach 4 screws 11230
on one side of both
divider panel GB . Then
turn boft divider panel
over and attach 4 screws
11230 on the other side.
Attach 4 screws 11230
on each side panel FA .

Assembly Instructions
7
Step 6
Front
1
FA FA
5
Front
x1
x1
x1
Front
Front Front Front
1.
2.
3.
4.
5.
Place drawer runners
1.
Extend drawer glide
41434 .
2.
Attach drawer glide at the
front of side panel FA .
Place screw 26020
through the correct hole
at the front of the drawer
glide, into the holes on
the side panel FA .
Tighten screw but do not
overtighten.
3.
Open slide until 3 holes
is visible at back of
drawer glide.
4.
Place screw 26020
through the correct holes
at the back of the drawer
glide, into the holes on
the panel FA .
Tighten screw but do not
overtighten.
5.
Attach the flat head
screw 25233 into the
correct holes of the
drawer glide, into the
side panel FA .
Tighten screw but do not
overtighten.
Repeat these 5steps for
the remaining runners.
Fittings you will need for this step:
Flat head screw
#26020 X8 Flat head screw #25233 X4 Drawer runner #41434 X4

GB
5
GB
1
Assembly Instructions
Step 7
8
Front
Front
Front
Attach drawer runners Flat head screw
#26020 X16
Flat head screw
#25233 X8 Drawer runner #41434 X8
Fittings you will need for this step:
Place drawer runners
1.
Extend drawer glide
41434 .
2.
Attach drawer glide at
the front of divider panel
GB .
Place screw 26020
through the correct hole
at the front of the drawer
glide, into the holes on
divider panel GB .
Tighten screw but do not
overtighten.
3.
Open slide until 3 holes
is visible at back of
drawer glide.
4.
Place screw 26020
through the correct holes
at the back of the drawer
glide, into the holes on
divider panel GB .
Tighten screw but do not
overtighten.
5.
Attach the flat head
screw 25233 into the
correct holes of the
drawer glide, into the
divider panel GB .
Tighten screw but do not
overtighten.
Repeat these 5steps for
the remaining runners on
both side on both divider
panel GB .

ID
x2
C
B
x2
A
C
B
Assembly Instructions
Step 9
Step 8
9
Fittings you will need for this step:
Flat head screw
# 26033 X22
Fittings you will need for this step:
Wedges
#33204 X4 Top
Bottom
Gathering profiles
Insert wedges 33204
into slots on the angle
ends of side profil B+
C , and front profile A.
Use a hammer.
Attaching panels
Place bottom panel ID
as shown, insert flat
head screw 26033 .