Argos New Hallingford 4 Door 3 Drawer Wardrobe User manual

New Hallingford
4 Door 3 Drawer Wardrobe
Dimensions
Width - 197,9cm
Depth - 60,3cm
Height -205,7cm
Assembly Instructions - Please keep for future reference
2497714
2574242
2377700
2588771
2478441
Tip : To prevent damage,
we recommend that you
build your unit on the
carton(s) it was packed in.
DR899244
Issue 6 - 20-12-2016
Important–Please read these instructions fully before starting assembly
Alternatively, call the Spares Helpline on: 0370 112 1928
For any other queries please contact the Customer Helpline on: 0345 640 2020
If you need help or have damaged or missing parts, please visit: www.argos-support.co.uk
or email: [email protected] (quoting your original order number)

2
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Safety and Care Advice
Important – Please read these instructionsfully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
• Parts of the assembly will be
easier with 2 people.
•To reduce the
likelihood of
damaging your
product please
ensure that your
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance
power drill is set on a low torque
setting.
Warning: Only use a manual
screwdriver to attach the hinges.
• Remove all fittings from the
plastic bags and separate them
into their groups.
unit or your floor.
to its final position (in the same
Instruction video
• This manual is provided with an additional instruction
video. If the icon on the right is displayed at a particular
step in the manual, Follow the link: http://nlink.nu/vid01
Or scan the QR code on the left with your phone.
See page 1 for link
to instruction video!

3
Right side
(205.6 x 58cm)
2
P2349C
Left side
(205.6 x 58cm)
1
P2349C
Upright x2
(196.9 x 57.7cm)
3
P2354C
Door x 2
(199.2 x 48.8cm)
15
P3724
Top/Bottom x 2
(194.9 x 57.7cm)
6
P1349
Large horizontal
(96.7 x 57.6cm)
7
P1342
Small horizontal x2
(47.6 x 57.6cm)
8
P1343
Drawer base x 2
(94.5 x 34.9cm)
9a
BO3395609B
Drawer base x 1
(94.5 x 34.9cm)
9b
BO3395609B60
Drawer wrap x 3
(35 x 95.8 x 10cm)
10
LA186809
Drawer front x 3
(97.9 x 15.7cm)
11
P4316
Plinth front
(194.8 x 14cm)
16
P7338C
Plinth back
(194.8 x 5.4cm)
17
P7339C
Pelmet
(198.1 x 4.5cm)
18
FA249
Foldy back
(152.3 x 98cm)
14
BO339340960/
BO33934160(CAT2588771)
Back x2
(199.3 x 48.8cm)
13
BO339020960/
BO33902160 (CAT2588771)
Left mirror door
(151.2 x 48.8cm)
PS3725
4Right mirror door
(151.2 x 48.8cm)
5
PS3719
For damaged or missing parts, please visit:
www.argos-support.co.uk or email: [email protected]
Components - Panels
Please check you have all the panels listed below

4
40mm Screw x 11
Ruler - Use this ruler to help correctly identify the screws
Tools required
A
20mm Screw x 12
B
24mm locking screw x 34
H
9mm Srew x 6
C
Door/Drawer handle x 10
Q
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Nail x 60
K
P
Small locking
nut x 6
N
Nail holder x 1
L
J
Hinge door x 12
R
Runner x 6
S
Glue x 1
FA1510
X
T
Phillips screwdriver
(medium & large)
Flatblade screwdriver
Small
hammer
Ruler
Drill
Eye protection
(when using a
hammer or drill)
5mm Suitable drill bit
GR1975
FK1268
FK1269
Hinge back x 12
FK1324
ILarge locking
nut x 34
FK1012
FK1010
FK1011
24mm locking screw x 6
H
FK1011
FK1981
FK1980
15mm Screw x 45
D
FK1400
Drawerbase Support x 12
10mm Fixing screw drawer x 12
E
12.5 mm Screw x 6
F
FK1301 FK1309
Peg x 2
FK1234
FA1515
FK1419
FK1250
PM16951
2.5mm Suitable drill bit
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Stairs
Piercer Scissors
(medium)
(small)spirit level
Setsquare
M
Hanger rail support x 6
FK1217
W
Wall plug and parkerscrew x 1
ZF99936
20mm Screw x 8
B
FK1980
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
For damaged or missing parts, please visit:
www.argos-support.co.uk or email: [email protected]
Components - Fittings
Tape measure
VU
Hanger rail small x 2
PM1873
Hanger rail large x 1
PM1884
L-Bracket x 1 15mm Screw x 12
O
G
FK1311
FK1235
Fittings Drawers
Fittings Carcase

5
Assembly Instructions
Step 1
Drawer assembly x 3
a: Insert two small locking
nuts Jinto drawer wrap
0.
Make sure the ‘arrow’ on
Jis pointing towards the
hole in the edge of 0.
H
b: Screw 24mm locking
screws Hinto holes
shown on back of drawer
front !.
Make sure 24mm locking
screws Hare tightened
right up against drawer
front !.
10
J
J
11
H
H
H
a:
b
c: Slide drawer base 9
into grooves shown on
drawer wrap 0.
9a/b
10
c:
11

6
Assembly Instructions
Step 1 - continued
Attaching runners
a: Slide top of runners R
foreward and fix on upright
3as shown using 10mm
fixing screw drawer E.
d: Insert glue in drawer
front !groove.
Turn the drawer wrap
assembly over and push
onto drawer front !. Use
a philips or flatblade
screwdriver, that is a good
fit, to turn small locking nut
Jas far as it will go - more
than 1/2 turn.
H
d
X
J
e:
e: Fix drawer handle T
onto drawer front !using
30mm screw B
Turn over drawer and
slide Drawerbase supports
Nin corner as shown and
fix them, using the
attached screws .
11
N
T
11
B
B
Step 2
Finished
front edge
a:
R
E
J
J
N
T
B
B
E
R
Attention!
There are two uprights
3one is the right side
, the other is the
left side , either of
them can be used as
or !
3R
3R
3L
3L
3R
3R
3L
3L
Finished
front edge
R
R
R
R
R
R
E
E
E
E
E
E
N
N

7
Finished
front edge
b
E
E
R
R
E
E
E
E
E
E
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
b
a:
Step 2 - continuedStep 2 - continued
b: Slide top of runners R
back.
Fix through 3rd hole of
runner Rand pre-drilled
holes of upright 3using
10mm fixing screw drawer
E.
Fix through 1st and 9th
hole of runners Rusing
15mm screw O.
Note: there are no pre-
drilled holes for 15mm
screw O.
Step 3
Insert fittings
a: Screw 24mm locking
screw Hinto 1 upright 3,
this will be the right upright.
Note: Insert 24mm locking
screw Has far as shown.
Do not over tighten.
Attach hinge back Ponto
upright 3.
Attach hanger rail
support Musing 12.5mm
screw Fonto upright 3.
Flip panel
H
3
H
H
H
H
H
H
H
H
H
M
M
3F
F
3
P
P
P
P
PP
P
M
M
M
F
F
F
Finished
front edge
Finished
front edge
b: Screw 24mm locking
screw 3into upright N,
this will be the right upright.
Attach hanger rail support
Musing 12.5mm screw F
onto upright 3.H
HH
3R
3R
3L
Finished
front edge
3L
3L
3L
R
R
R
R
R
R
Finished
front edge
Finished
front edge
3R
3R
b
Assembly Instructions
Attention!
There are two uprights
3one is the right side
, the other is the
left side , either of
them can be used as
or !
3R
3R
3L
3L
Warning: Do not use an electric screwdriver to attach the
hinges as this can weaken the fixing.

8
Assembly Instructions
Step 4
Step 5
Position large horizontal
7onto upright .
Insert two large locking
nuts Iinto large
horizontal 7as shown.
Use a screwdriver to turn
locking nuts Iclockwise
to lock.
H
H
H
H
I
I
6
7
73L
3L
3R
3R
I
I
I
I
I
Attaching panels
Position large horizontal 7
onto upright .
Insert two large locking
nuts Iinto large
horizontal 7฀as shown.
Use a screwdriver to turn
locking nuts Iclockwise
to lock.
Note: Internal Uprights
are identical. Large holes
for locking nuts should not
face each other”.
Step 6
Insert fittings
Screw 24mm locking screw
Hinto top/bottom 6,
this will be the top.
Note: Insert 24mm locking
screw Has far as shown.
Do not over tighten.
H
3
Attaching panels Unfinished
back edge

9
Assembly Instructions
Step 7
A
AA
A
A
A
A
A
H
H
H
H
I
I
I
I
I
I
I
6
6
Attaching plinths
Align the sides of plinth
front ^with bottom 6as
shown and attach using
40mm screw A.
Note: there are no
predrilled holes for
40mm screw A.
Note: top and bottom
panels 6are identical.
Only prepare one of the
panels at this stage. This
will be the bottom panel
Repeat with plinth back
&.
Step 8
Insert locking screws
Screw 24mm locking
screw Hinto bottom 6.
Finished
front edge
Finished
front edge
I
I
I
I
Step 9
Attaching panels
Position bottom 6and top
6onto uprights 3.
Insert four Large locking
nuts Iinto uprights 3as
shown.
Use a screwdriver to turn
locking nuts Iclockwise to
lock.
I
I
16
17

10
Assembly Instructions
Step 10
Attaching panels
Position small horizontals
8onto uprights 3.
Insert three large locking
nuts Iinto small
horizontals 8as shown.
Use a screwdriver to turn
locking nuts Iclockwise
to lock.
H
H
H
H
H
H
H
H
H
H
H
H
I
I
I
I
I
I
M
M
P
3
3
2
2
1
1
8
8
Step 11
H
1
P
M
1F
F
F
P
P
P
P
P
H
H
Finished
front edge
Insert fittings
a: Screw 24mm locking
screw Hinto left side 1
and right side 2.
Note: Insert 24mm locking
screw Has far as shown.
Do not over tighten.
Attach hinge back Ponto
left side 1and right side
2.
Attach hanger rail support
Musing 12.5mm screw
F฀onto left side 1and
right side 2.
12
Step 12
Attaching panels
Position left side 1and
right side 2onto the unit.
Insert large locking nuts
I฀into top/bottoms 6
and small horizontals 8
as shown.
Use a screwdriver to turn
locking nuts Iclockwise
to lock.
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Warning: Do not use an electric screwdriver to attach the
hinges as this can weaken the fixing.