Argos 356/3018 User manual

Asha - Cabin Bed
Dimensions
Width - 195cm
Depth - 95cm
Height - 45cm
Issue 1 - 9/30/13
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6400800
Assembly Instructions - Please keep for future reference
379/7482
356/3018

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your oor.
• Parts of the assembly will be
easier with 2 people.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
• WARNING: Do not place this child`s bed near heat
sources, windows and other furniture.
• WARNING: Do not use this child`s bed if any part is
broken, torn or missing.
• WARNING: Not suitable for children under the age of
4 years.
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and ttings are
tightend properly.
Handy Hints
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
Right side panel (95 x 42.5 cm)
1
Door (62.5 x 34.5 cm)
7
Front/back bed support x4 (73 x 7 cm)
8
Middle bed board (95 x 64.5 cm)
9
Left/right central support x2 (63 x 16 cm)
10
Middle central support (63 x 16 cm)
11
Left/right bed board x2 (95 x 63.8 cm)
12
Bottom panel x3 (80.7 x 62.9 cm)
13
Left side panel (95 x 42.5 cm)
2
Left/right crossbar x4 (63 x 8 cm)
3
Middle crossbar x2 (63 x 8 cm)
4
Right shelf partition (95 x 36.5 cm)
5
Left shelf partition (95 x 36.5 cm)
6
If you have damaged or missing components,
call the Customer Helpline: 0345 6400800

Please check you have all the ttings listed below
50mm wood screw x 14
Ruler - Use this ruler to help correctly identify the screws
Tools required
A
Screw-in dowel x 6
E
50mm xing screw x 28
B
Hinges x 2
H
30mm wooden dowel x 20
C
Mounting plate x 2
I
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
Cap x 6
F
Locking nut x 6
D
30mm wood screw for handle x 1
K
N
Stopper x 1
G
Handle x 1
12mm wood screw x 18 Allen key x 2
J
Components - Fittings
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Eye protection
(when using a
hammer)
16mm wood screw x 8
L
M
3
100 20 30 40 50 60 70 80 90 100
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
The screws length is measured from the head to the point (30mm screw shown).
Drill

Assemble right module
Two people are needed
here.
a: Insert 3 pieces 30mm
wooden dowels Cinto
right side panel 1and
3 pieces 30mm wooden
dowels Cinto right shelf
partition 5.
b: Position the boards
like shown on the picture.
Use 3 pieces 50mm
wood screws Ato
x the right central
support 10 and the right
crossbars 3to the right
side panel 1.
Use 3 pieces 50mm
xing screws Bto
x the right central
support 10 and the right
crossbars 3to the right
shelf partition 5.
Use the Allen key Nto
tighten the 50mm wood
screw Aand the 50mm
xing screw B.
Note: The right crossbars
3have to be placed
with the groove looking
down and pointing inside
the bed like shown on the
picture.
4
Assembly Instructions
Step 1
A
A
A
B
B
B
C
C
C
C
C
C
Clockwise
A
N
Groove - this way down
Groove - this way down
5
5
1
1
10
3
3
Clockwise
B
N
a:
b:

a:
b:
5
Assembly Instructions
Step 2
B
B
B
C
C
C
C
C
C
A
A
A
Clockwise
A
N
2
6
10
3
3
2
6
Clockwise
B
N
Assemble left module
Two people are needed
here.
a: Insert 3 pieces 30mm
wooden dowels Cinto
left side panel 2and 3
pieces 30mm wooden
dowels Cinto left shelf
partition 6.
b: Position the boards
like shown on the picture.
Use 3 pieces 50mm
wood screws A to x
the left central support
10 and the left crossbars
3to the left side panel
2.
Use 3 pieces 50mm
xing screws B to x
the left central support
10 and the left crossbars
3to the left shelf
partition 6.
Use the Allen key Nto
tighten the 50mm wood
screw Aand the 50mm
xing screw B.
Note: The left crossbars
3have to be placed
with the groove looking
down and pointing inside
the bed like shown on the
picture.
Groove - this way down
Groove - this way down

Assembly Instructions
Attaching panels
Two people are needed
here.
a: Insert 3pcs 30mm
wooden dowels Cto
the left shelf partition 6
and 3pcs 30mm wooden
dowels Cto the right
shelf partition 5. Insert
3pcs screw-in dowels E
to the left shelf partition
6and 3pcs screw-in
dowels Eto the right
shelf partition 5.
Use a phillips screwdriver
for the screw-in dowels
E.
After inserting the dowels
and the screw-in dowels
position the modules like
shown on the picture.
Note: Position of wooden
dowels Cand screw-in
dowels Eon the right
shelf partition 5is
identical to the left shelf
partition 6.
b: Position the middle
central support 11 and
the middle crossbars 4.
Insert the locking nuts D
and use a screwdriver to
turn them clockwise to
lock.
Put the caps Fof the
locking nuts.
a:
b:
Step 3
E
E
E
E
E
C
C
C
C
E
C
C
D
D
D
D
D
D
F
F
F
F
F
F
6
6
5
54
4
11
D
E
6

Assembly Instructions
Attaching panels
Two people are needed
here.
a: Insert the 30mm
dowels Cto the left side
panel 2and to the right
side panel 1like shown
on the drawing. Position
the left and the right bed
boards 12 .
Note: Position of wooden
dowels Con the right
side panel 1is identical
to the left side panel 2.
a:
b:
b: Screw the left and
the right bed boards
12 through 50mm
xing screw Bto the
construction of the bed.
Use the Allen key Nfor
the 50mm xing screws
B.
Step 4
C
C
B
B
B
B
212
12
12
12
1
Clockwise
B
N
Continued on next page.
7

c:
d:
Assembly Instructions
c: Position the middle
bed board 9and screw
it to the middle central
support 11 through
50mm xing screw B.
Use the Allen key Nfor
the 50mm xing screw
B.
Step 5
d: Screw the middle
bed board 9, the left
bed board 12 and the
right bed board 12 to
right shelf partition 5
and to left shelf partition
6 through 50mm xing
screw B.
Use the Allen key Nfor
the 50mm xing screws
B.
Attaching panels
Position the front and the
back bed supports 8
and screw them to the
middle bed board 9, to
the left bed board 12 and
to the right bed board
12 through 50mm xing
screw B.
Use the Allen key Nfor
the 50mm xing screws
B.
Step 4 - continued
B
B
B
B
B
B
B
B
B
B
B
B
9
11
12
9
6
512
8
12
12
9
8
8
8
Clockwise
B
N
Clockwise
B
N
Clockwise
B
N
8

Assembly Instructions
Attaching panels
First screw the front and
the back bed supports
8to the right side panel
1and to the left side
panel 2through 50mm
wood screw A. After that
screw the left and the
right bed boards 12 to
the left side panel 2and
to the right side panel
1through 50mm wood
screw A.
Use the Allen key N.
Note: Position of wood
screws Aon the left side
panel 2is identical to
the right side panel 1.
Rotate the construction
of the bed at 180
degrees with the top
down like shown on the
picture.
Attaching panels
Screw the bottom panels
13 to the left crossbar
3, to the right crossbar
3and to the middle
crossbar 4through
12mm wood screw M.
Note: Make sure you
centralised the panels
before xing them.
Use the pilot holes holes
to screw the panels to
the construction of the
bed.
Step 7
Step 6
12
12
1
13
13
13
3
3
3
4
8
8
8
8
2
A
A
A
A
A
A
N
A
A
A
M
M
M
MM
M
MM
M
M
M
MM
M
MM
M
M
180
9