Argos Ohio 309/5256 User manual

MADE IN
BRITAIN
Dimensions
Width - 120cm
Depth - 49.5cm
Height - 37.5cm
Ohio - Coffee Table
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 16/10/14
Important - Please read these instructions fully before starting assembly
ALR3079
309/5256
Issue 1 - 16/10/14 - Dalton changed to Ohio

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 25kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
Please check you have all the panels listed below
2
5
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Top (D1772A)
(1200 x 495mm)
Plinth (D1778A)
(1020 x 95mm)
Horizontal (D1776A)
(499 x 415mm) x 2
Back (D1777A)
(499 x 146mm) x 2
Fascia (D1781A)
(350 x 70mm) x 4
Left Side (D1773B)
(350 x 419mm)
6
1Right Side (D1774B)
(350 x 419mm)
Left Drawer Front (D1779A)
(504.5 x 160mm)
Right Drawer Front (D1780A)
(504.5 x 160mm)
2 3 4
7
9
12
10 11
8
13 14 Drawer Back (W451-124)
(451 x 124mm) x 2
Left Drawer Side (W370-95RH)
(370 x 95mm) x 2
Left Drawer Side (W370-95LH)
(370 x 95mm) x 2
Divider (D1775B)
(255 x 417mm)
Drawer Base (T462-347)
(462 x 347mm) x 2

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A
Wooden dowel (F22) x 16
B
Metal dowel (F901) x 32
C
D
Large locking
nut (F900) x 28
F
H I
Small locking
nut (F3) x 4
19mm Screw (F461) x 4
G
Knock-in Peg (F171) x 8
13mm Screw (F63) x 12
E
Handle (F287) x 2
JR Runner (F160) x 2
b
L Runner (F161) x 2
Jc
L Runner (F159) x 2
Ja
R Runner (F162) x 2
Jd
9mm Screw (F73) x 12
K
L
Plastic Nail (F91) x 5
Wedgefix (F639) x 4

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
B
B
B
D
Step 2
Prepare the drawer
fronts
Screw 2 metal dowels
into the holes shown on
the back of the left
drawer front and the
right drawer front .
Note: Tighten the metal
dowels up fully against
the panels.
B
9
10
Step 3
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer fronts and .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
12
9 10
D
12
D
Note: The left drawer
front has a small
identification hole.
9
13
13
B
B
B
B
910
x 2
x 2
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
D
12
13
DD
13
x 2
D
12
910
12
13
Groove

G
G
Assembly Instructions
5
Step 4
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
14
12 13
11
14
14
E
12 13
Attach the handles
Attach a handle to
each drawer front
and using 2 screws .
F
G
9
10
x 2
x 2
F
910
K
Step 7
Fit the wedgefixes
Turn the 2 drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
K
E
E
12
13
11
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front and .
11
12 13
9 10
E
910
x 2
x 2
E12
13
14
11
K
K

Prepare 2 fascias with
holes nearest this side
Prepare 2 fascias with
holes nearest this side
A
A
Assembly Instructions
6
Step 8
Fit runners to the
drawers
Turn the drawer
assemblies over.
Fit the runner to the
bottom edge of the left
drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front and . Use a
bradawl to mark the
fixing positions, then
secure with 2 screws .
Fit the runner to the
bottom edge of the right
drawer side using the
same method.
13
J c
12
9 10
I
J d
Step 9
Prepare the 4 fascias
Check that the holes are
in the same place as the
diagrams, as each pair
are prepared differently.
Screw 2 metal dowels
into each of the 4 fascias
. .
Tap a wooden dowel
into each of the 4 fascias
. .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
B
4
10mm
A
4
AB
B
B
B
4
x 2
x 2
4
I
I
Runners must be
pushed up against
the drawer front
J c
x 2
I
I
J d
13
12
9
10

A
Assembly Instructions
7
Step 10
J a
H H
1st
screw
2nd
screw H
3rd
screw
Finished
front edge
J a
I
Finished
front edge
I
C
C
C
C
C
C
B
B
B
B
b:
c:
d:
a:
Prepare the left side
a: Fit a runner to
the left side .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the 2nd hole in at the top
of the runner .
c: Insert 6 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Tap a wooden dowel
into the left side .
d: Screw 4 metal
dowels into the left
side .
J a
1
H
H
I
B
1
C
1
A
1
J a
1
1
1
1
C
H
J a
H
H

Assembly Instructions
8
Step 11
Fit 2 fascia panels to
the left side
a: Push the left side
down onto a fascia panel
. .
b: Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the left side .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
c: Push a fascia panel
. down onto the left
side .
d: Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the left side .
1
4
1
4
C
1
C
1
C
4
C
B
a:
b:
c:
d:
1
1
4
C
1
4
1
4

A
Assembly Instructions
9
Step 12
J b
I
J b
HH 1st
screw
2nd
screw
H
C
3rd
screw
I
C
C
C
C
C
B
B
B
B
Prepare the right side
a: Fit a runner to
the right side .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the 2nd hole in at the top
of the runner .
c: Insert 6 large locking
nuts into the right
side .
Tap a wooden dowel
into the right side .
d: Screw 4 metal
dowels into the right
side .
J b
2
H
H
I
B
2
C
2
A
2
J b
b:
c:
d:
a:
2
2
2
2
H
H
J b
H