Argos Hallingford 305/2763 User manual

Hallingford - 4 Door 3 Drawer Wardrobe
Dimensions
Width - 197,9cm
Depth - 60,3cm
Height -205,7cm
Issue 1 - 24/05/13
Important – Please read these instructionsfully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400800
Assembly Instructions - Please keep for future reference
305/2804
305/2794
305/2770
305/2787
305/2763
Tip : To prevent damage,
we recommend that you
build your unit on the
carton(s) it was packed in.
DR89924

2
Safety and Care Advice
Important – Please read these instructionsfully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
pages 2 and 3.
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
•This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Glue safety - Take care when using glue, please follow the advice below

Components - Panels
Please check you have all the panels listed below
3
Right side
(205.6 x 58cm)
2
P2349b
Left side
(205.6 x 58cm)
1
P2349b
Upright x2
(196.9 x 57.6cm)
3
P2354b
Door x 2
(199.2 x 48.8cm)
15
P3304
Top/Bottom x 2
(194.9 x 57.7cm)
6
P1349
Large horizontal
(96.7 x 57.6cm)
7
P1342
Small horizontal x2
(47.6 x 57.6cm)
8
P1343
Drawer base x 3
(94.5 x 34.9cm)
9
BO33956
Drawer wrap x 3
(35 x 95.8 x 10cm)
10
LA1868
Drawer front x 3
(97.9 x 15.7cm)
11
P4309
Plinth front
(194.8 x 14cm)
16
P7338C
Plinth back
(194.8 x 5.4cm)
17
P7339C
Pelmet
(198.1 x 4.5cm)
18
FA249
Foldy back
(152.3 x 98cm)
14
BO33934
Back x2
(199.3 x 48.8cm)
13
BO33902
Left mirror door x1
(151.2 x 48.8cm)
4
PS3323
Right mirror door x1
(151.2 x 48.8cm)
5
PS3324

4
Please check you have all the ttings listed below
40mm Screw x 11
Ruler- Use this ruler to help correctly identify the screws
Tools required
A
10mm Fixing screw drawer x 12
E
20mm Screw x 20
B
24mm locking screw x 40
H
9mm Srew x 6
C
I
Door/Drawer handle x 10
Q
Note: The quantities below are the correct amount to complete the assembly. In some cases more
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
V
12.5 mm Screw x 6
F
L-Bracket x 1
15mm Screw x 45
D
Nail x 60
K
15mm Screw x 12
O
Large locking
nut x 34
M
P
Small locking
nut x 6
N
U
Nail holder x 1
L
G
J
Hinge door x 12
R
Runner x 6
S
Hanger rail small x 2
T
Components - Fittings If you have damaged or missing components,
call the Customer Helpline: 0845 6400800
Phillips screwdriver
(medium & large)
Flatblade screwdriver
Small
hammer
Ruler/tape
measure
Drill
Eye protection
(when using a
hammer or drill)
5mm Suitable drill bit
GR1975 PM1873
Hanger rail large x 1
PM1884
FK1268FK1269
Hinge back x 12
FK1324
FK1012
FK1010
FK1011
FK1301
FK1981
FK1980
FK1400
FK1311
FK1235
Hanger rail support x 6 Drawerbase Support x 6
FK1217
FK1309
Peg x 2
FK1234
FA1515 FK1419
FK1250
PM16951
5mm Suitable drill bit
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Stairs
Piercer Scissors
(medium)
(small)
Level ruler
Setsquare
W
Wall plug and parkerscrew x 1
ZF99936

5
Assembly Instructions
Step 1
Drawer assembly x 3
a: Insert two small locking
nuts into drawer wrap
.
Make sure the ‘arrow’ on
is pointing towards the
hole in the edge of .
J
10
H
b: Screw 24mm locking
screws into holes shown
on back of drawer front
.
Make sure 24mm locking
screws are tightened
right up against drawer
front .
J
10
10
J
J
11
H
H
H
H
11
11
H
a:
b:
c: Slide drawer base
into grooves shown on
drawer wrap .
9
10
9
10
c:
11

6
Assembly Instructions
Step 1 - continued
Attaching runners
d: Turn the drawer wrap
assembly over and push onto
drawer front . Use a philips
or atblade screwdriver, that
is a good t, to turn small
locking nut as far as it will
go - more than 1/2 turn.
11
H
d:
J
e:
e: Fix drawer handle
onto drawer front using
30mm screw
Turn over drawer and
slide Drawerbase supports
in corner as shown and x
them, using the attached
screws .
11
T
11
B
N
N
T
11
B
B
Step 2
a: Slide top of runners
foreward and x on upright
as shown using 10mm
xing screw drawer .
R
E
Finished
front edge
a:
R
E
3
J
J
J
N
T
B
B
AA
E
R
Attention!
There are two uprights one is
the right side , the other is the
left side .
3
3R
3L
3R
3R
3L
3L
Finished
front edge
R
R
R
R
R
R
E
E
E
E
E
E

7
Assembly Instructions
Finished
front edge
b:
E
E
R
R
E
E
E
E
E
E
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
b:
a:
Step 2 - continuedStep 2 - continued
b: Slide top of runners
back.
Fix through 3rd hole of
runner and pre-drilled
holes of upright using
10mm xing screw drawer
.
Fix through 1st and 9th hole
of runners using 15mm
screw .
Note: there are no pre-
drilled holes for 15mm
screw .
b: Slide top of runners
back.
Fix through 3rd hole of
runner and pre-drilled
holes of upright using
10mm xing screw drawer
.
Fix through 1st and 9th hole
of runners using 15mm
screw .
Note: there are no pre-
drilled holes for 15mm
screw .
E
O
R
R
3
R
O
Step 3
Insert ttings
a: Screw 24mm locking
screw into 1 upright ,
this will be the right upright.
Note: Insert 24mm locking
screw as far as shown.
Do not over tighten.
Attach hinge back onto
upright .
H
3
H
H
H
H
H
H
H
H
H
3
M
M
3
H
H
Attach hanger rail
support using 12.5mm
screw onto upright .
Flip panel
F
F
M
F
P
3
3
P
3
3
P
P
P
PP
P
M
M
M
F
F
F
Finished
front edge
Finished
front edge
b: Screw 24mm locking
screw into upright ,
this will be the right upright.
N
Attach hanger rail support
using 12.5mm screw
onto upright .
MF
3
H
HH
3R
3R
3L
Finished
front edge
3L
3L
3L
R
R
R
R
R
R
Finished
front edge
Finished
front edge
3R
3R
b:

8
Assembly Instructions
Step 4
Step 5
Attaching panels
Position large horizontal
onto upright .
Insert two large locking nuts
into large horizontal
as shown.
Use a screwdriver to turn
locking nuts clockwise to
lock.
H
H
H
H
H
H
I
I
I
I
I
6
6
7
7
7
7
3L
3L
3R
3R
I
I
I
I
I
Attaching panels
Position large horizontal
onto upright .
Insert two large locking nuts
into large horizontal
as shown.
Use a screwdriver to turn
locking nuts clockwise to
lock.
Note: Internal Uprights
are identical. Large holes for
locking nuts should not face
each other”.
I
I
7
7
Step 6
Insert ttings
Screw 24mm locking screw
into 1top/bottom ,
this will be the top.
Note: Insert 24mm locking
screw as far as shown.
Do not over tighten.
H
3

9
Assembly Instructions
Step 7
A
AA
A
A
A
A
A
H
H
H
H
I
I
I
I
I
I
I
6
6
Attaching plinths
Align the sides of plinth
front with bottom as
shown and attach using
40mm screw .
Note: there are no
predrilled holes for 40mm
screw .
Note: top and bottom
panels are identical.
Only prepare one of the
panels at this stage. This
will be the bottom panel
Repeat with plinth back
.
6
A
17
16
Step 8
Insert locking screws
Screw 24mm locking
screw into bottom .
H6
A
6
Finished
front edge
Finished
front edge
I
I
I
I
Step 9
Attaching panels
Position bottom and top
onto uprights .
Insert four Large locking nuts
into uprights as shown.
Use a screwdriver to turn
locking nuts clockwise to
lock.
3
3
6
6
I
I
I
I

10
Assembly Instructions
Step 10
Attaching panels
Position small horizontals
onto uprights .
Insert three large locking
nuts into small
horizontals as shown.
Use a screwdriver to turn
locking nuts clockwise
to lock.
H
H
H
H
H
H
H
H
H
H
H
H
I
I
I
I
I
I
I
I
M
M
P
3
3
3
2
2
2
2
2
2
1
1
1
1
1
1
6
8
8
8
8
8
Step 11
H
1
P
M
1F
F
F
P
P
P
P
P
H
H
Finished
front edge
Insert ttings
a: Screw 24mm locking
screw into left side
and right side .
Note: Insert 24mm locking
screw as far as shown.
Do not over tighten.
Attach hinge back onto
left side and right side
.
H
H
Attach hanger rail support
using 12.5mm screw
onto left side and right
side .
MF
P
12
Step 12
Attaching panels
Position left side and
right side onto the unit .
Insert large locking nuts
into top/bottoms and
small horizontals as
shown.
Use a screwdriver to turn
locking nuts clockwise
to lock.
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I