Argos Ohio 6+2 Sideboard 314/7128 User manual

MADE IN
BRITAIN
Dimensions
Width - 120cm
Depth - 39.5cm
Height - 78cm
Ohio - 6+2 Sideboard
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 3 - 12/03/15
Important - Please read these instructions fully before starting assembly
ALR3081
314/7128
Issue 1 - 15/10/14 - Dalton changed to Ohio.
Drillings on Sides and Uprights have been moved because the runners are now fitted using skinny euros.
Drillings on Base moved so dowels don’t clash with runner screws.
The Drawer Sides and Drawer Back are now 124mm deep.
O/B Bracket and Screw replaced with Strap kit.
Added 5 plastinails.
Added 12 Wedgefixes.
Issue 2 - 10/11/14 - Base dimensions changed to 1016 x 350mm.
Plinth dimensions changed to 1016 x 95mm.
Dowels added to the drawing in Step 24b.
Issue 3 - 12/03/15 - Amended the text in Step 15 to read ‘The 1st screw uses the 1st hole...’ to match the diagram.
Updated helpline number.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 43kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
80%
x 2
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Shelf (D1791A)
(334 x 350mm) x 2
Top (D1811A)
(1200 x 395mm)
Plinth (D1816A)
(1016 x 95mm)
1
Door (D1808A)
(492 x 342mm) x 2
4 5
2
18
19
13
15
17
3
16
14
12
6
Fascia (D1806A)
(755 x 70mm) x 2
7
8 9 Central Drawer
Front (D1817A)
(322 x 162mm) x 4
Back (X921)
(1038 x 669mm)
Left Drawer
Front (D1818A)
(342 x 162mm)
Right Drawer
Front (D1819A)
(342 x 162mm)
10 11
Divider (D1815B)
(645 x 349mm) x 2
Base (D1814B)
(1016 x 350mm)
Left Side (D1812B)
(755 x 357mm)
Right Side (D1813B)
(755 x 357mm)
Large Drawer
Base (T297-347)
(297 x 347mm) x 2
Small Drawer
Base (T266-347)
(266 x 347mm) x 4
Small Drawer
Back (W255-124)
(255 x 124mm) x 4
Left Drawer
Side (W350-124LH)
(350 x 124mm) x 6
Right Drawer
Side (W350-124RH)
(350 x 124mm) x 6
Large Drawer
Back (W286-124)
(286 x 124mm) x 2

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 10
B
Metal dowel (F901) x 32
C
D
Large locking
nut (F900) x 20
F
H
19mm Screw (F461) x 16
I
Small locking
nut (F3) x 12
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
K
G
Knock-in Peg (F171) x 24
L
N O
Shelf support (F121) x 8
13mm Screw (F63) x 44
E
Nail (F51) x 23
M
Hinge plate
(F523) x 4 Hinge (F522) x 4 Handle (F287) x 8
PR Runner (F160) x 6
b
L Runner (F161) x 6
Pc
L Runner (F159) x 6
Pa
R Runner (F162) x 6
Pd
J
9mm Screw (F73) x 36
QStrap
Screw Washer x 2
Overbalance protector kit (F269) x 1
Plastic Nail (F91) x 5
Wedgefix (F639) x 12

9
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
x 6
x 4x 1x 1
x 6
x 6
B
B
D
Step 2
Prepare the drawer
fronts
Screw 2 metal dowels
into the holes shown on
the left drawer front ,
the right drawer front
and the 4 central drawer
fronts .
Note: Tighten metal
dowels up fully against
the panels.
B
10
11
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Step 3
D
8
9
Attach the drawer
sides to the drawer
fronts
Push the left drawer side
. and right drawer side
. onto the back of the
drawer fronts ,
and .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
8
10
12
11
D
8
DDD
89
D
Note: The left drawer
front has a shallow
identification mark.
10
9
9
10 11 12
B
B
B
10 11
B
B
B
12
12
80%
x 2
8

G
G
Assembly Instructions
5
Step 4
Fit the drawer bases
a: Slide the large drawer
base down the
grooves in the drawer
sides and and
down into the groove in
the left drawer front
and right drawer front .
b: Slide the small
drawer base down
the grooves in the
drawer sides and
and down into the
groove in the central
drawer fronts .
Step 5
Fit the drawer backs
a: Fit the large drawer
back between the
drawer sides and .
Make sure that the large
drawer base fits into
the groove in the large
drawer back .
Hold the large drawer
back in position and
tap the knock-in pegs
through the holes in the
drawer sides and .
b: Fit the small drawer
back between the
drawer sides and .
Make sure that the small
drawer base fits into
the groove in the small
drawer back .
Hold the small drawer
back in position and
tap the knock-in pegs
through the holes in the
drawer sides and .
15
98
10
11
16
98
12
G
G
G
13
8 9
15
13
13
G
8 9
14
8 9
16
14
14
G
8 9
x 2
8
9
15
10 11
12
x 2
8
9
16
x 4
Fit back panel
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
down onto the unit, as
shown.
Use the nail guide to
hold the nails vertical
and at the correct
distance whilst you nail
around the top and sides
of the back .
Note: Nails should
be spaced about 150mm
apart.
Stand the unit up for
the next step.
a:
a:
b:
b:
G
G
x 4
G
8
9
15
13
8
9
16
14

Assembly Instructions
Step 6
Step 7
Step 8
Attach the handles
Attach a handle to
each drawer front ,
and using 2 screws .
O
H
10
12
11
x 2 x 4
x 6
H
H
O
10
11
H
H
O
12
6
Fit runners to the
drawers
Fit the runner to the
bottom edge of the left
drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front , and .
Use a bradawl to mark
the fixing positions, then
secure with 2 screws .
Fit the runner to the
bottom edge of the right
drawer side using the
same method.
9
P c
8
10 11 12
K
P d
x 6
K
K
K
K
Runners must be
pushed up against
the drawer front
P d
11
12
10
P c
I
Fit the wedgefixes
Turn all of the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
I
I
I

Assembly Instructions
7
Step 9
Step 10
Left fascia - holes
nearest this side
A
A
B
B
B
Prepare the 2 fascias
Check that the holes are
in the same place as the
diagrams, as one will be
the left fascia and one
will be the right fascia.
Screw 3 metal dowels
into each of the 2 fascias
. .
Tap a wooden dowel
into each of the 2 fascias
. .
7
7
B
7
10mm
A
7
B
B
B
Ax 1
x 1
Right fascia - holes
nearest this side
Prepare the left side
Insert 3 large locking
nuts into the left side
. .
Note: The arrow on the
locking nuts must point
towards the holes in the
edge of the panel.
C
C
C
4
C
4
C

Assembly Instructions
8
Step 11
Step 12
a:
b:
Join the left side to
the left fascia panel
a: Push the left side
down onto the left fascia
panel .
b: Use a screwdriver to
tighten the 3 large
locking nuts fitted to
the left side .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
4
7
C
4
C
Dowel
this end
4
7
7
4
C
B
Left fascia
C
Prepare the right side
Insert 3 large locking
nuts into the right
side .
C
5
C
C
C5
C

Assembly Instructions
9
Step 13
Join the right side to
the right fascia panel
a: Push the right side
down onto the right
fascia panel .
b: Use a screwdriver to
tighten the 3 large
locking nuts fitted to
the right side .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
C
B
C
7
5
7
5
7
C
5
C
b:
a:
Dowel
this end
5
Right fascia
5