Argos Adult Malibu 563/6307 User manual

MADE IN
BRITAIN
Dimensions
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
More help is available throughout this booklet by scanning
in the QR codes or typing in the links
Malibu - 3 Drawer 2+2 Door Robe
Assembly Instructions - Please keep for future reference 563/6307
544/3985
563/7038
544/3930
553/4038
Width - 145.9cm
Depth - 49.8cm
Height - 180.5cm
Issue 2 - 24/06/16

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 102kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2, 3, 4 and 5.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: To prevent
possible overbalancing this unit
must be secured to a wall
using the 2 overbalance
protector kits supplied or, an
alternative fixing method of your
choice.
• Dispose of all packaging
carefully and responsibly.
When applicable, remove any protective film
from the panels before they are used

Components - Panels
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the panels listed below When applicable, remove any
protective film before use
2
Left Side (DF7367)
(179 x 49.6cm)
Right Side (DF7368)
(179 x 49.6cm)
8 9 Left Divider (DF7373)
(168.25 x 47.4cm)
10 Right Divider (DF7374)
(168.25 x 47.4cm)
11
Top (DF7369)
(145.9 x 49.8cm)
6Base (DF7370)
(142.5 x 49.4cm)
7
1
5
2Drawer Front (DF5996)
(70.8 x 15.7cm) x 3
Drawer Base
(T676-447)
(67.6 x 44.7cm) x 3
Left Drawer
Side (WB450-130LH)
(45 x 13cm) x 3
Right Drawer
Side (WB450-130RH)
(45 x 13cm) x 3
3Drawer Back
(W665-130)
(66.5 x 13cm) x 3
4

3
Components - Panels
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the panels listed below When applicable, remove any
protective film before use
12 Plinth (DF7375)
(142.5 x 9.2cm ) x 2
13 Cross Rail (DF5858)
(71.4 x 6cm)
14 Back Rail (DF7376)
(34.05 x 9.2cm) x 2
17 Top Rail (DF7356)
(34.05 x 6cm) x 2
15 Narrow Shelf (DF7372)
(34.05 x 47.2cm) x 2
18 Left Door (DF6012)
(119.6 x 35.25cm)
21 Small Back (X1709-360)
(170.9 x 36cm) x 2
22 Large Back (X1709-727)
(170.9 x 72.7cm)
20 Large Door (DF7377)
(167.6 x 35.25cm) x 2
19 Right Door (DF6013)
(119.6 x 35.25cm)
16 Horizontal (DF5862)
(71.4 x 47.2cm) x 2
Long Hanging Rail (FHR708)
(70.8cm long)
23
Short Hanging Rail (FHR334)
(33.4cm long) x 2
24

Please check you have all the fittings listed below
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
4
Drawer Fittings Bag marked ‘drw kit’
A
Quickfit dowel (F545) x 6
C
Knock-in Peg (F171GY) x 12
D
19mm Screw (F461) x 6
Large locking cam nut (F607) x 6
B
13mm Screw (F63) x 12
F
HG
9mm Screw (F73) x 18
Main Fittings Bag
A
Quickfit dowel (F545) x 28
D
19mm Screw (F461) x 4
M
Wooden dowel (F22) x 48
I
Nail (F51) x 44
J
B
K
Rail Holder (F891) x 6
L
Plastic Nail (F91) x 6
F
13mm Screw (F63) x 18
Door Buffer (F137) x 6
Large locking cam nut (F607) x 36
O
Double metal dowel (F566) x 4
N
Large wooden dowel (F40) x 10
40mm Screw (F910) x 4
Q
Back holder (F276) x 12
P
Nail screw (F277) x 12
E
15mm Screw (F284) x 6

Components - Fittings
5
Individual Fittings Bags
T
S
Handle (F418) x 10
Pre-mounted
hinge (F419) x 12
436mm long
Drawer Brace (F427) x 3
U
M
VCR Runner (F609) x 3
b
DL Runner (F610) x 3
Vc
CL Runner (F608) x 3
Va
DR Runner (F611) x 3
Vd
450mm long
CR
CL
DR
DL
Overbalance protector
kit (F474) x 2
R
Rule
Tools required
Rule
ScissorsSquare
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Step
ladder
Electric drill
(only use
when drilling
into walls)

6
Step 1
Assembly Instructions
Step 2
Fit the drawer sides
to the 3 drawer fronts
Push the left drawer
sides . and right
drawer sides . down
onto the back of the 3
drawer fronts .
Turn the large locking
cam nuts clockwise
as far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
2
1
3
Prepare the drawer
sides
a: Insert a large locking
cam nut into the left
drawer sides and the
right drawer sides .
Note: The arrow on the
locking cam nut must
point towards the
hole in the end of the
panel.
b: Push 1 of the quickfit
dowels as far as it will
go into the left drawer
sides and the right
drawer sides .
Note: Only the plastic
thread of the quickfit
dowel sticks out from the
panel.
A
2
3
B
2
3
x 3
11 1
3
B
B
a:
b:
B
x 3 x 3
23
BB
A
x 3 x 3
23
AA
Use the Drawer Fittings Bag marked ‘drw kit’ for Steps 1 - 7
2
hps://www.youtube.com/watch?v=HclfJdkm-Lg
Standard Drawer Box Assembly

Assembly Instructions
7
Step 3
Fit the drawer bases
Slide a drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 4
Fit the drawer backs
Fit a drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
5
32
1
4
2 3
5
4
4
C
2 3
x 3
x 3
x 3
Step 5
Fit the handles
Attach 2 handles to
each drawer front
using screws .
S
D
1
D
S
D
S
1
1
3
2
5
3
5
C
C
2
C
C
4

8
Step 6
Assembly Instructions
x 3
Fit the drawer braces
Turn the 3 drawer
assemblies over and
hook a drawer brace
onto the bottom edge of
the drawer back .
Fix it to the drawer front
. and drawer back
using 2 screws .
U
E
U
E
U
E
E
E
U
x 3
V d
Fit runners to the
drawers
Fit the DL runner to
the bottom edge of the
left drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front . Use a bradawl
to mark the fixing
positions, then secure
with 2 screws .
Fit the DR runner to
the bottom edge of the
right drawer side
using the same method.
3
V c
2
1
F
V d
DR
Step 7
3
2
1
DL
F
F
F
F
V c
DL
4
4
1 4
Runners must be
pushed up against
the drawer front
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Fixing Bottom Mounted Runners
1

Finished
front edge
Finished
front edge
Finished
front edge
9
Step 8
Assembly Instructions
Prepare the left divider
a: Fit 3 CL runners
to the left divider .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the hole at the top of the
runner .
Fit a rail holder to the
left divider through
the top hole with screw
and into the mark hole
drilled in the left divider.
Make sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
c: Insert 2 large locking
cam nuts into the left
divider .
Push 2 of the quickfit
dowels as far as they
will go into the left
divider .
Tap 6 wooden dowels
into the left divider .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
V a
10
G
G
F
B
10
10
V a a:
b:
c:
A
M
10
K
F
F
10
V a
G1st
screw
Finished
front edge
CL
Finished
front edge
F
Use the Main Fittings Bag for Steps 8 - end
CL
G
V a
G
G
CL
G
V a
G
G
CL
G
V a
G
G
CL
F
CL
F
CL
F
CL
CL
CL
AM
MM
A
B
B
10
10
10
M
M
M
F
K
FK
F
F
K
10mm
M
A
B
V a
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Fixing Bottom Mounted Runners

10
Step 9
Assembly Instructions
a:
b:
c:
V b
G
1st
screw
Finished
front edge
CR
Finished
front edge
F
A
B
CR
G
V b
G
G
CR
G
V b
G
G
CR
G
V b
G
G
Prepare the right
divider
a: Fit 3 CR runners
to the right divider .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the hole at the top of the
runner .
Fit a rail holder to the
right divider through
the top hole with screw
and into the mark hole
drilled in the right divider.
Make sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
c: Insert 2 large locking
cam nuts into the
right divider .
Push 2 of the quickfit
dowels as far as they
will go into the right
divider .
Tap 6 wooden dowels
into the right divider .
V b
11
G
G
F
B
11
11
V b
A
M
11
K
F
F
11
11
Finished
front edge
CR
F
CR
F
CR
F
CR
CR
CR
AM
MM
A
B
B
M
M
M
F
F
K
11
Finished
front edge
11
Finished
front edge

Finished
front edge
11
Step 10
Assembly Instructions
Prepare just 1 of the
horizontals
Insert 4 large locking
cam nuts into 1 of the
horizontals .
B
B
B
B
Finished
front edge
B
16
16
Finished
front edge
F
F
K
F
F
K
Prepare the other
surface of the dividers
Turn the left divider
and right divider over
Fit a rail holder to the
left divider and the
right divider through
the top hole with screw
and into the mark hole.
Make sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
K
F
F
10
11
Turn both of the dividers over
10
11
Step 11

O
O
N
N
N
Finished
front edge
12
Step 12
Assembly Instructions
Fit the horizontal to
the right divider
Push the horizontal
onto the right divider .
Tap 2 double metal
dowels through the
right divider and into
the horizontal until
they ‘’bottom out’’.
Turn the 2 large locking
cam nuts fitted to the
horizontal clockwise
as far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
16
11
Fit 3 large wooden
dowels
Tap 3 large wooden
dowels through the
right divider and into
the horizontal until
they ‘’bottom out’’.
O
B
CR
11
CR
11
N
11
16
Finished
front edge
16
11
16
16
16
Step 13
OB
B

13
Step 14
Assembly Instructions
CR
Finished
front edge
16
11
Fit the horizontal to
the right divider
Push the horizontal
onto the right divider .
Turn the 2 large locking
cam nuts fitted to the
horizontal clockwise
as far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
16
11
B
16
N
N
Fit the cross rail
Push the cross rail up
against the right divider
. .
Tap 2 large wooden
dowels through the
right divider and into
cross rail until they
‘’bottom out’’.
N
11
13
11
13
CR
11
13
Finished
front edge
Prepare the other
horizontal
Insert 4 large locking
cam nuts into the
horizontal .
Push 4 of the quickfit
dowels as far as they
will go into the horizontal
. .
Tap 6 wooden dowels
into the horizontal .
B
16
16
16
A
A
M
M
M
A
A
M
M
M
A
B
B
B
B
Finished
front edge
16
A
B
M
hps://www.youtube.com/watch?v=9C7tgv5xnbE
Carcase Assembly
Step 16
Step 15

Finished
front edge
14
Step 17
Assembly Instructions
Step 19
CR
13
Fit the left divider
Push the left divider
onto the assembly.
Tap 2 double metal
dowels through the
left divider and into
the horizontal at the
top of the unit until they
‘’bottom out’’.
Turn the 4 large locking
cam nuts fited to the
2 horizontals
clockwise as far as
they will go to secure
the panels.
Important: Make
sure there is no gap
between the fitted
panels.
10
B
16
16
10
16
CR
13
16
10
N
N
N
Fit 3 more large
wooden dowels
Tap 3 large wooden
dowels through the
left divider and into
the horizontal until
they ‘’bottom out’’.
N
10
16
Step 18
Fit 2 large wooden
dowels
Tap 2 large wooden
dowels through the
left divider and into
the cross rail until
they ‘’bottom out’’.
N
10
13
O
O
CR
13
N
N
16
16
10
O
10
16
Top of unit
13

15
Step 20
Assembly Instructions
Step 21
Prepare 1 of the
narrow shelves
Insert 4 large locking
cam nuts into the
narrow shelf .
Push 2 of the quickfit
dowels as far as they
will go into the narrow
shelf .
Tap 3 wooden dowels
into the narrow shelf .
B
15
15
15
A
Step 22
M
Finished
front edge
15
A
M
M
M
A
B
B
B
B
Prepare the 2 top rails
Tap 2 wooden dowels
into each of the 2 top
rails .
M
17 M
M
Finished
front edge
x 2
x 1
17
Finished
front edge
17
Fit the 2 top rails
Push 1 of the top rails
onto the left divider .
Push the other top rail
onto the right divider .
CR
13
10
Finished
front edge
17
17
10
17
11
11

Finished
front edge
15
M
M
A
A
M
16
Step 23
Assembly Instructions
Step 25
Fit the narrow shelf
Push the narrow shelf
onto the left divider .
Turn the 2 large locking
cam nuts fited to the
narrow shelf
clockwise as far as they
will go to secure the
panels.
Important: Make
sure there is no gap
between the fitted
panels.
Prepare the other
narrow shelf
Insert 4 large locking
cam nuts into the
narrow shelf .
Push 2 of the quickfit
dowels as far as they
will go into the narrow
shelf .
Tap 3 wooden dowels
into the narrow shelf .
B
15
15
15
A
Step 24
M
Finished
front edge
15
B
B
CR
13
10 15
15
10
B
15
CR
13
11
B
B
Fit the narrow shelf
Push the narrow shelf
onto the right divider .
Turn the 2 large locking
cam nuts fited to the
narrow shelf
clockwise as far as they
will go to secure the
panels.
Important: Make
sure there is no gap
between the fitted
panels.
15
11
B
15

M
A
Finished
front edge
A
M
M
M
A
17
Step 26
Assembly Instructions
Step 27
A
M
M
M
A
B
B
B
B
Finished
front edge
7
Prepare the base
Insert 4 large locking
cam nuts into the
base .
Push 4 of the quickfit
dowels as far as they
will go into the base .
Tap 6 wooden dowels
into the base .
B
7
7
7
A
M
CR
13
Fit the base
Push the base onto
the assembly and secure
it using 4 screws .
H
H
H
H
7
H
7
Prepare the back rails
Insert 2 large locking
cam nuts into each of
the 2 back rails .
Push 2 of the quickfit
dowels as far as they
will go into each of the 2
back rails .
Tap 2 wooden dowels
into each of the 2 back
rails .
B
14
14
14
A
M
Step 28
M
A
BFinished
front edge
14
B
x 2
Note: To make it easier to fit the
top and base panels, place
polystyrene blocks from the
packaging underneath the divider
panels to raise the assembly.
Polystyrene
block

Finished
front edge
18
Step 29
Assembly Instructions
Step 30
AM
MM
B
B
A
Prepare the right side
Fit a rail holder to the
right side through the
top hole with screw
and into the mark hole
drilled in the right side.
Make sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
c: Insert 2 large locking
cam nuts into the
right side .
Push 2 of the quickfit
dowels as far as they
will go into the right side
. .
Tap 3 wooden dowels
into the right side .
F
F
K
K
F
F
9
B
9
9
A
M
9
Finished
front edge
Finished
front edge
Fit the back rail to the
right side
Push the back rail
onto the right side .
Turn the large locking
cam nut fitted to the
back rail clockwise
as far as it will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
14
9
B
14
14
9
9