Argos Misaki 632/4546 User manual

MADE IN
BRITAIN
Dimensions
Width - 141cm
Length - 199cm
Height - 75.5cm
Misaki - Double Bed
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 09/12/10
Important - Please read these instructions fully before starting assembly
632/4546
632/4553
ALR2560

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 63kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
Please check you have all the panels listed below
2
1
80%
x 3
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
End Panel (D0690A)
(1403 x 312mm) x 2
2Side Rail (D0691A)
(1904 x 133mm) x 2
3
Drawer Back (D0701A)
(1360 x 119mm) x 2
Mid Rail (D0692A)
(1904 x 275mm)
5
Footboard (D0693A)
(1411 x 390mm)
Headboard (D0694A)
(1411 x 390mm)
9
6Headboard Strut (D0695A)
(600 x 123mm) x 3
Drawer Front (D0698A)
(1395 x 162mm) x 3
10
Blanking Panel (D0696A)
(504 x 177mm) x 2
Left Drawer End (D0699A)
(650 x 120mm) x 2
13
Right Drawer End (D0700A)
(650 x 120mm) x 2
Drawer Bottom Supports (D0702A)
(634.5 x 123mm) x 3
Drawer Base (X783)
(1370 x 644.5mm) x 2
12
14
4
7
11
Blanking Return (D0697A)
(652.5 x 177mm) x 2
8

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 22
B
Metal dowel (F901) x 38
D E
60mm screw (F888) x 6
F
G H I
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
see malibu fitment mk2 for large number of panels and fittings
Large locking
nut (F900) x 38
C
45mm Screw (F65) x 19 Barrel nut (F1047) x 6
19mm Screw (F461) x 16
Handle (F855) x 6
Connecting Sleeve (F432) x 4
K
Castor (F627)
x 12
13mm Screw (F63) x 24
L
Flat-head
screwdriver
J
38mm Screw (F81) x 12
M
Allen Key (F36) x 1

A
A
A
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Prepare the mid rail
Push 2 barrel nuts
into the mid rail .
Screw a metal dowel
into the mid rail .
Note: Tighten metal
dowels up fully against
the panels.
Tap 4 wooden dowels
into the mid rail as
shown.
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Turn the mid rail over
Screw a metal dowel
into the mid rail .
E
B
Step 1
Prepare the 2
blanking returns
Insert 3 large locking
nuts into each of the
blanking returns as
shown.
Note: The arrow on the
locking nuts must point
towards the holes in the
edge of the panel.
Tap 2 wooden dowels
into each of the blanking
returns as shown.
Step 2
80%x 2
90%x 1
80%x 1
B
E
B
3
3
B
3
E3
A
A
10mm
A
A
3
C
C
C
F
C
8
8
A
A
8
A
C
C
C
8
A
This hole is
not used
This hole is
not used
B
3
Turn the mid rail over

A
Assembly Instructions
5
Step 3
3
Step 2
Join the mid rail and
an end panel
Push the mid rail
onto an end panel .
Note: Make sure that
the slot in the barrel nut
. is horizontal.
Screw through the end
panel using bolt
and on into the barrel nut
. in the mid rail .
Step 3
1
E
3
1
E
E
1F
3
F
3
B
C
3
8
8
Join the mid rail and
blanking returns
Push the 2 blanking
returns onto the mid
rail .
Use a screwdriver to
tighten the large locking
nut fitted to each of
the blanking returns
as shown.
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
8
3
C
8
C
CC
BB
Prepare the 2
blanking panels
Insert 2 large locking
nuts into each of the
blanking panels .
Screw 2 metal dowels
into each of the blanking
panels .
Tap a wooden dowel
into each of the blanking
panels .
Step 4
Fit the blanking
panels
Push the 2 blanking
panels onto the
blanking returns .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
each of the blanking
returns as shown.
Step 5
C
7
B
7
A
7
7
7
7
8
8
7
8
C
8
x 2
A
C
C
C
8
A
A
C
C
C
8
A
This hole is
not used
This hole is
not used
This lower hole
is not used
This upper hole
is not used

Assembly Instructions
6
Step 6
1
Prepare 1 of the end
panels
Screw 4 metal dowels
into only 1 of the end
panels .
Fit an end panel
Push the end panel
onto the assembly.
Note: Make sure that
the slot in the barrel nut
. is horizontal in the
mid rail .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
each of the blanking
panels as shown.
Screw through the end
panel using bolt
and allen key and on
into the barrel nut in
the mid rail .
Step 7
B
B
B
B
B
1
1
E
F
M
x 1
7
7
1
E
3
C
7
3
1
3
E
F
M

F
F
1
Assembly Instructions
7
Step 8
Prepare the 2 side
rails
Push 2 barrel nuts
into each side rail .
Tap 4 wooden dowels
into each side rail .
A
A
A
A
E
2
A
2
Fit the side rails
Push the side rails
onto the end panel .
Screw through the end
panel using bolts
and allen key and on
into the barrel nut in
the side rails .
Note: Support the side
rails until the other end
panel has been fitted in
the next step.
Step 9
2
1
1
2
F
E
2
Fit the other end
panel
Push the other end panel
. onto the assembly.
Screw through the end
panel using bolts
and on into the barrel
nuts fitted in the mid
rail and side rails .
F
F
F
2
3
2
1
1
1F
E
32
Fit the footboard
Fit the footboard by
screwing into its 4 holes
through the matching
holes in the end panel
using screws .
Step 3
4
4
1
1
E
x 2
E
E
2
2
M
M

Assembly Instructions
Step 10
2
2
F
F
F
Fit the other end
panel
Push the other end panel
. onto the assembly.
Screw through the end
panel using bolts
and allen key and on
into the barrel nuts
fitted in the mid rail
and side rails .
1
1F
E
3
2
Step 11
1
M
M
3
Fit the footboard
Fit the footboard by
screwing into its 4 holes
through the matching
holes in the end panel
using screws .
4
1
D
4
1
D
D
D
D
8

Assembly Instructions
9
Step 12
D
G
G
6
6
6
G
G
Fit the headboard
struts
Fit the middle
headboard strut
using 2 screws .
To fit the other 2
headboard struts ,
push the connecting
sleeves into the holes
and then screw the
screws in from the
other side.
6
D
6
H
G
H
H
H
H
Fit the headboard
Fix the headboard by
screwing into its 6 holes
through the holes in the
headboard struts
using screws.
Step 13
6
6
6
5
5
6
L
L
L
L
L
L